OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/boards/arm/mimxrt1050_evk/mimxrt1050_evk.yaml

24 lines
293 B
YAML
Raw Normal View History

boards: arm: Add NXP mimxrt1050_evk Adds support for the NXP MIMXRT1050-EVK board, an entry-level development board for the new mimxrt1052 Cortex-M7 SoC. Adds pinmuxing, dts, documentation, and jlink debug support for the new board. Note that pinmuxing uses the mcux pinmux driver directly rather than the Zephyr pinmux interface. The mimxrt1052 SoC has complicated pinmuxing that may require changing the Zephyr pinmux interface to support, so for now let's use the mcux driver directly. We are also not yet configuring the external flash, therefore a debugger is required to load code to the internal sram. The on-board OpenSDA circuit with jlink firmware is sufficient, and the 'make debug' build target is supported. Samples tested include: hello_world, philosophers, synchronization, basic/blinky, and basic/button. Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
2017-08-12 03:46:04 +08:00
#
# Copyright (c) 2017, NXP
#
# SPDX-License-Identifier: Apache-2.0
#
identifier: mimxrt1050_evk
name: NXP MIMXRT1050-EVK
type: mcu
arch: arm
toolchain:
- zephyr
build: Replace GCC ARM Embedded with GNU Arm Embedded The old GCC ARM Embedded website on launchpad (https://launchpad.net/gcc-arm-embedded) has been superseeded by the new GNU Arm Embedded one (https://developer.arm.com/open-source/gnu-toolchain/gnu-rm). This also means a change of name from "GCC" to "GNU". Reflect this in the enviroment variables so that the proper term is used henceforth. Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
2018-08-03 23:11:23 +08:00
- gnuarmemb
boards: arm: Add xtools as a supported toolchain Update all ARM boards to have xtools as a supported toolchain. Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
2019-01-10 00:25:16 +08:00
- xtools
mimxrt1050_evk: default external flash and sdram Moved from ITCM and DTCM to HyperFlash and SDRAM. Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
2019-01-31 18:33:27 +08:00
ram: 32768
flash: 65536
mimxrt1050_evk: Configure an lpspi instance and pins Enables an instance of the lpspi peripheral, configures the pinmuxes, and updates the board documentation accordingly. Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
2018-09-15 05:23:27 +08:00
supported:
boards: mimxrt1050_evk: Enable mcux elcdif driver and pins Enables the mcux elcdif shim driver and pin muxes on the mimxrt1050_evk board. Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
2019-01-03 03:51:51 +08:00
- display
boards: mimxrt1050_evk: Enable mcux lpi2c driver and pins Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1050_evk board. Updates the board documentation and yaml supported list accordingly. Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
2019-01-17 21:07:24 +08:00
- i2c
mimxrt1050_evk: Configure an lpspi instance and pins Enables an instance of the lpspi peripheral, configures the pinmuxes, and updates the board documentation accordingly. Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
2018-09-15 05:23:27 +08:00
- spi
mimxrt1050_evk: enabling networking hardware Enables Networking hardware on i.MX-RT 1050-EVKB board. Pinout enabled board specific etherenet connection, also pin initialization was moved later to PRE_KERNEL_2 in order to have sysclock initialized before. Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
2018-11-16 00:28:47 +08:00
- netif:eth
drivers: hwinfo: add driver support for NXP i.mx RT device ID Add driver support for NXP i.mx RT ID device. This device has an ID of 8 bytes. Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
2019-02-05 02:53:59 +08:00
- hwinfo
boards: mimxrt1050_evk: configure USB device EHCI driver for rt1050 set usbd1 status as OK in mimxrt1050_evk.dts add usb_device supported information in rt1050 yaml file. Signed-off-by: Mark Wang <yichang.wang@nxp.com>
2019-05-05 13:20:49 +08:00
- usb_device