117 lines
1.8 KiB
Plaintext
117 lines
1.8 KiB
Plaintext
/*
|
|
* Copyright (c) 2018 AJ Palmer
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/f7/stm32f746Xg.dtsi>
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32F746ZG-NUCLEO board";
|
|
compatible = "st,stm32f746zg-nucleo", "st,stm32f746";
|
|
|
|
chosen {
|
|
zephyr,console = &usart3;
|
|
zephyr,shell-uart = &usart3;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
zephyr,dtcm = &dtcm;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
green_led: led_0 {
|
|
gpios = <&gpiob 0 GPIO_INT_ACTIVE_HIGH>;
|
|
label = "User LD1";
|
|
};
|
|
blue_led: led_1 {
|
|
gpios = <&gpiob 7 GPIO_INT_ACTIVE_HIGH>;
|
|
label = "User LD2";
|
|
};
|
|
red_led: led_2 {
|
|
gpios = <&gpiob 14 GPIO_INT_ACTIVE_HIGH>;
|
|
label = "User LD3";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button_0 {
|
|
label = "User";
|
|
gpios = <&gpioc 13 GPIO_INT_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &green_led;
|
|
led1 = &blue_led;
|
|
led2 = &red_led;
|
|
sw0 = &user_button;
|
|
};
|
|
};
|
|
|
|
arduino_serial: &usart6 {};
|
|
arduino_i2c: &i2c1 {};
|
|
arduino_spi: &spi1 {};
|
|
|
|
&usart3 {
|
|
current-speed = <115200>;
|
|
pinctrl-0 = <&usart3_pins_b>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&usart6 {
|
|
current-speed = <115200>;
|
|
pinctrl-0 = <&usart6_pins_a>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&usbotg_fs {
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&timers1 {
|
|
status = "okay";
|
|
|
|
pwm {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&spi1 {
|
|
/*
|
|
* WARNING: The pin PA7 will conflict on selection of SPI_1 and
|
|
* ETH_STM32_HAL. See pinmux.c for further details.
|
|
*/
|
|
status = "okay";
|
|
};
|
|
|
|
&iwdg {
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|
|
|
|
&can1 {
|
|
bus-speed = <125000>;
|
|
sjw = <1>;
|
|
prop-seg = <0>;
|
|
phase-seg1 = <6>;
|
|
phase-seg2 = <5>;
|
|
status = "okay";
|
|
};
|
|
|
|
&adc1 {
|
|
status = "okay";
|
|
};
|