Names that begin with an underscore are reserved by the C standard.
This patch does not change names of functions defined and implemented
in header files.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This adds Enable advertising with Node Identity BTP command and
it's implementation.
This command is needed to pass PTS MESH/NODE/CFG/NID/BV-02-C
test case.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This command has been agreed and implemented in tester application.
The patch updates BTP document only.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
The current script relies on a hardware reset pin to release the chip
from reset. Software reset is also possible and even required in case
the reset pin hasn't been wired to the J-Link connector on the board.
This patch adds an additional command line switch to nrfjprog.py that
uses the software reset mechanism of nrfjprog instead of pin reset.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
btusb_bulk_out() reads the EPOUT buffer in multiple of 4 bytes because
of Quark's USB FIFO size limitation. But this has later been taken care
internally in the DW driver making it redundant in hci_usb.
Remove Quark specific handling and read the whole EPOUT buffer at once.
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
try_write() writes the whole net buffer to USB which sometimes is larger
than the maximum packet size of an endpoint.
Use the ret_bytes param to know how much has been written to the USB bus
and write the remaining chunks in the subsequent calls.
Usually the USB driver write doesn't happen immediately in cases where
the usb_write() is not synchronous. In such cases, USB driver returns
-EAGAIN.
If driver returns -EAGAIN, yield so as to give other threads a chance
to run while waiting for previous USB write to complete.
Signed-off-by: Sundar Subramaniyan <sundar.subramaniyan@gmail.com>
This patch reworks the current ARM __swap() function into a C function.
Due to some issues with using svc calls withing fault handlers, we
needed to change the way we initiate a swap by removing the dependence
on svc #0.
Before __swap() is called, the system has already done an irq_lock().
Upon return from __swap(), the equivalent of an irq_lock() is done due
to restoration of the key value from the irq_lock preceeding the call.
For ARM V6M (M0/M0+), the pendsv bit is toggled and the irqs are
enabled. There is no priority masking in v6m, so it's just a global
enable. For ARM V7M, the priority mask has to be set to 0x0 to allow
for the pendsv IRQ to be taken. This is done for both via a call to
irq_unlock(0).
After this unlock, a pendsv irq will be taken, either at the tail end
of the current irq handling if we are in handler mode, or immediately
due to the pendsv being asserted (no other outstanding irqs). The next
thread will be scheduled.
Upon return from the context switch to the original
thread, the priority mask will already be correct due to the pendsv
processing.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the missing 'max_num_pending_alerts' argument to the
K_ALERT_DEFINE used in the "Signaling an Alert" code example.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
As USB port is present on the board, and pinmux configured,
add USB support in board dts file.
Configure Ethernet oer USB as default net i/f
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename variable zpkt to cpkt to complete the move from ZoAP to CoAP.
Remove unused tests/net/lib/zoap/CMakeLists.txt file.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Update VERSION file to 1.11.0-rc3. This should have been done for the
earlier 1.11.0-rcX releases but was forgotten.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixed spelling and formatting issues (a blank line is required before
the first item in a list, or sublist).
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
To comply with Zephyr Contributing guidelines regarding
ext/ components, update README for STM32L4 series
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To comply with Zephyr Contributing guidelines regarding
ext/ components, update README for STM32F7 series
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To comply with Zephyr Contributing guidelines regarding
ext/ components, update README for STM32F4 series
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To comply with Zephyr Contributing guidelines regarding
ext/ components, update README for STM32F3 series
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To comply with Zephyr Contributing guidelines regarding
ext/ components, update README for STM32F1 series
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To comply with Zephyr Contributing guidelines regarding
ext/ components, update README for STM32F0 series
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit fixes a bug in the ARM HardFAult handler, which
prevented from dumping the right UsageFault flags, after a
UsageFault had escalated to HardFault.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
* the bug comes out when a context switch happens in interrupt
* the bug only affects the em7d in emsk 2.3
* the bug is caused by
* wrong operations of stack
* wrong setting of SEC_STAT's IRM bit
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Change TICKS_PER_SEC from 1000 to 100
* em_starterkit is a FPGA board with cores running at max 30 Mhz.
1000 ticks per second is a little heavy for it.
* the tests/kernel/common requires 200 ticks per second at most,
or the testcase will stall.
disable the generation of bin file.
* there is no flash in em_starterkit
* there is huge gap between ICCM and DCCM which will cause the bin
file too large, alomst 2GB
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Keyword FLASH_HAS_PAGE_LAYOUT is related to flash and should
be declared in its Kconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
It was possible to have enable flash module while no flash driver
implementation was enabled. This cause coverity issues and unnecessary
initialization call.
This pat introduce FLASH_HAS_DRIVER_ENABLED Kconfig keyword which is
selected once any flash driver is enabled. flash_map switch its
dependency to this keyword.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Loop counter was type of signed int while it was compared
to unsigned lvalue in loop condition.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Test of f. flash_area_get_sectors was failing because parameter for
passing capacity of the sectors array was uninitialized.
This patch fix this bug.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
All Sphinx-generated pages for tagged release documentation include the
release version number in the breadcrumb header. This patch adds this
to the "Latest" daily doc build results that are the default pages seen
when visiting docs.zephyrproject.org
Fixes: #6432
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
pthread_setschedparam() uses k_thread_priority_set()
to set pthread priority. There is an error in argument
in k_thread_priority_seti() due to which system correct
priority was not set. Correcting this error.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
timer_gettime() internally uses k_timer_remaining_get()
to get time remaining to expire. Time unit for
k_timer_remaining_get is msec not ticks.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
When using the LE Create Connection Cancel command, the controller is
supposed to return a Command Complete first and then an LE Connection
Complete Event after. Since the Link Layer does not generate an event in
this case emulate the behavior in the HCI layer instead.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Michael Hope