Introduce NXP LCDIC driver using MIPI DBI class. This peripheral
supports 8080 and SPI 3/4 wire mode, although only SPI 4 wire support is
currently implemented. The driver supports DMA and interrupt driven
transfers.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add devicetree binding for NXP LCDIC. This controller is capable of
driving displays in 8080 or SPI 3/4 wire mode, and optionally swapping
endianness of display data as it sends it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Resolved a data race in shell.c by copying the user-provided
prompt-string into a private buffer within the shell, ensuring
proper synchronization with the shell-thread.
Fixes: #64972
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@verkada.com>
The soc_secure_* function are used by the non-secure application
to access hardware resources which are mapped as secure.
Using these functions for hardware resources mapped as non-secure
is missleading.
We have some soc_secure_* functions which read FICR values.
In nRF91 and nRF53 platforms this made sense since FICR
has hardware fixed mapping as secure.
For nRF54 though the FICR has hardware fixed mapping as non-secure.
This change refactors the soc_secure.h to exclude the functions
which read FICR values from being included when FICR is mapped as
non-secure.
Also updates the hwinfo and ieee802154 drivers to adjust to this change.
Signed-off-by: Georgios Vasilakis <georgios.vasilakis@nordicsemi.no>
Adds an option that allows for locking all interrupts when reading
the data from this sensor, this can be used alongside systems like
Bluetooth to vastly increase chances of getting a reading from the
sensor successfully, at the risk of losing Bluetooth packets.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Add pinctrl and board enablement for LPUART2, which is broken out to
P4_2 and P4_3 on the FRDM board.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add EDMA channels for LPUART RX and TX to LPFLEXCOMM 2 and 4, as these
nodes are enabled with the UART driver
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
For demonstration purposes add a way to capture some arbitrary
data and send it in cooked mode for analysis.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If there are multiple tunnels, then use the tunnel device name
to select the correct one. Note that this tunnel is only used
for network packet capture in this sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
User is able to enable packet capture for low level HDLC data
frames received from and sent to network. This data can sent to
remote system for analysis. The captured data is encapsulated
into Linux cooked mode SLL packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If user created the capture device using the API and not via
the shell, then the device name was not set. Use the default
capture device in this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The event NET_EVENT_CAPTURE_STARTED is generated when the
capture is enabled, and NET_EVENT_CAPTURE_STOPPED when capture
is disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
As user might not know the capture device name, allow
net_capture_is_enabled() to be called with a NULL device name.
Currently it then uses the hardcoded device name, but we could
change that in the future so that the function could figure out
the correct name itself.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The net_capture_pkt() does not return information what happened
to the net_pkt because the packet was always cloned. With cooked
capture we can avoid the cloning in which case we need to know
the capture status in order to unref the packet if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add support for capturing arbitrary data via the cooked mode (sll)
capture API. The actual packet capture is done using net_capture_data()
function, the packet capture infrastructure does not need any changes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add ETH_P_CAN, ETH_P_CANFD and ETH_P_HDLC protocol types so that they
can be used in following commits.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Allow user to create a kitchen sink pseudo a.k.a any network
interface that one is only able to write to. This might seem
unnecessary, but it is possible to attach virtual network
interfaces on top of this pseudo interface. These virtual
interfaces could then process the data for example for
packet capture purposes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
For debugging purposes it would be nice to see the verdict
printed as a string instead of number.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add a recv callback to dummy API. After this it is possible to
receive data by a dummy network interface. This is only useful
if one attaches a virtual interface on top of the dummy one.
One such example is the cooked mode capture interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The CONFIG_MAX_THREAD_BYTES=3 needs to be set for multiple
boards like mr_canhubk3 and xiao_ble when running in usermode.
Too many thread objects (18)
Increase CONFIG_MAX_THREAD_BYTES to 3
Fixes#70955
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
The native_posix compilations fail with various socket
errors like this:
samples/net/sockets/echo_server/src/udp.c:45:26: error: implicit \
declaration of function ‘socket’ [-Werror=implicit-function-declaration]
45 | data->udp.sock = socket(bind_addr->sa_family, SOCK_DGRAM,
| IPPROTO_UDP);
Disable the native_posix board from networking samples so that CI can pass.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Improve Twister command line arguments for memory footprint:
* group and order footprint arguments meaningfully,
* clearer help descriptions,
* resolve logical inconsistences for combinations of arguments,
in particular:
`--last-metrics` now forces `--enable-size-report`,
`--show-footprint` now controls only detailed log output of
footprint deltas in comparison modes.
* align twister tests accordingly.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Improve code consistency and fix CONFIG_POSIX_API=n compatibility with use
of ZSOCK_* and DNS_* macros.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Refactor the skip collaborator logic to add log messages when a
collaborator is skipped because they self removed of not part of the
org.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The "frdm_k64f" is referred as frdm_k64f and ``frdm_k64f`` in
places, update them to ":ref:`Freedom-K64F <frdm_k64f>`" or
``frdm_k64f``.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Change 'Hawkbit' and 'hawkbit' to 'hawkBit' wherever
makes sense, and a bit of touch ups here and there.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The initial version of an input driver for Cirque Pinnacle ASIC supports:
* Setting sensitivity
* Choosing between relative and absolute modes
* Relative mode
* Primary tap
* Swapping X and Y
* Absolute mode
* Setting number of idle packets
* Clipping coordinates outside of active range
* Scaling coordinates
* Inverting X and Y coordinates
Signed-off-by: Ilia Kharin <akscram@gmail.com>
Add harness as twister by default looks into ztest results and
in bluetooth configuration they won't be find.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
To prevent postponing data flush until filling fifo. Now the flush will
occur at the scheduled time, regardless of subsequent poll_out reqs.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Daniel DeGrasse