Fix possible race conditions when state and results are written
by locking the registry, so a first write does not cause Notify
message to be send too early.
Signed-off-by: Juha Heiskanen <juha.heiskanen@nordicsemi.no>
Rename the STM32H7 FDCAN node labels to match to naming used in the ST
reference manuals. This also matches the naming used in the STM32H7 FDCAN
clock and pinctrl macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the STM32H7 FDCAN driver Kconfig symbol and implementation file to
match the naming used in the ST reference manuals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the STM32 FDCAN node labels to match to naming used in the ST
reference manuals. This also matches the naming used in the STM32 FDCAN
pinctrl macros.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the STM32 FDCAN driver Kconfig symbol and implementation file to
match the naming used in the ST reference manuals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the STM32 bxCAN driver DTS compatible, Kconfig symbol, and
implementation file to match the naming used in the ST reference manuals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fold the contents of the private header for the STM32 bxCAN driver into the
implementation file.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The compile script was modified to fully parallelize
all bsim test images builds.
This speed up the build time, but as we are
building ~80 images, the average load on the system
will skyrocket to over 200.
For CI systems we are seeing in quite many cases,
the CI server loosing connection with the CI runner,
while this part of the job is run, and suspect it is
due to this load.
Nice the job down (by the default +10),
as this should alleviate this problem without slowing
down the job.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
When the protocol layer like TCP is blocking transmission, the socket
layer will attempt and wait for a maximum amount of time before returning
with an ENOBUFS error.
This change allows to set the maximum waiting time from the configuration
file instead of using a fixed 10 second value.
Signed-off-by: Sjors Hettinga <s.a.hettinga@gmail.com>
Qualification test CSIS/SR/SP/BV-03-C [Lock Timeout]
Specification: Coordinated Set Identification Service Revision v1.0.1
Section 5.3.1.1.
When the server and the client are not bonded and they disconnect when
the value of the Set Member Lock characteristic is set to Locked, the
server shall set the value of the Set Member Lock characteristic to
Unlocked immediately after the disconnection.
Signed-off-by: Henrik Eriksen <heri@demant.com>
Qualification test MICS/SR/SPE/BI-01-C [Invalid Mute Value]
Specification: Microphone Control Service Revision v1.0 Section 3.1.1
If the client writes a value of Disabled or RFU to the Mute
characteristic, the server shall return an ATT Error Response with the
ATT error code Value Not Allowed (0x13) as defined in Assigned Numbers.
Signed-off-by: Henrik Eriksen <heri@demant.com>
The timing_max parameters defined in the stm32 bxcan driver don't match the
register description in the reference manuals.
- sjw does have only 2 bits representing 1 to 4 tq.
- phase_seg1 and phase_seg2 max is one tq higher.
I have checked the following reference manuals and all match:
- RM0090: STM32F405, F415, F407, F417, F427, F437 AND F429
- RM0008: STM32F101, F102, F103, F105, F107 advanced arm-based mcus
- RM0351, RM0394: all STM32L4
- RM0091: all STM32F0 with CAN support
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The API was never implemented.
The channel type can also be obtained using bt_iso_chan_get_info().
If we would have to implement this API, it would share a lot of the
implementation with bt_iso_chan_get_info().
Removing the API makes the ISO APIs more similar to the ACL APIs
where we don't have a special API to fetch the role.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
RD-client tests should wait longer for expected events.
Also the stubbed service worker should be stopped properly
after tests.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Bootstrap executable cause socket to be closed, so
it requires some delay for Ack to be send out as well.
Similarly, add small delay for Update trigger, so the
possible Ack goes out before the actual update message.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
When BOOTSTRAP FINNISH message was received, it caused
engine to immediately switch to BOOTSTRAP_TRANS_DONE state
which then closed the connection.
Ack packet was still on the send-queue so it never got send before close().
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Some state changes were do by directly writing into
client.engine_state variable, followed by call next_event_at(0);
This causes hard-to-find side effects.
Refactor all state transitions to use set_sm_state() to have better
control for it.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Following #60410, the NXP S32 external interrupt controller device
initializes after the core interrupt controller. Bump the NXP S32 intc
init level to initialize after the core intc and before the GPIO
device driver.
Fixes#61218
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Test fixed group address acceptance condition, which has been clarified
in Mesh Protocol 1.1: A node shall deliver a message to the model
subscribed to a fixed group address even if the corresponding feature
is disabled.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Reduce the main clock frequency from 150MHz to 144MHz which allows meeting
the full range of CAN bitrates.
Fixes: #60811
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
adds dts support for general purpose timer to accomodate timer driver
bringup on aglex and agilex5
Signed-off-by: Balsundar Ponnusamy <balsundar.ponnusamy@intel.com>
We use ZTEST_DMEM and ZTEST_BMEM for running tests with memory shared
between userspace and kernelspace. This ought to be documented.
Document ZTEST_DMEM and ZTEST_BMEM.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
The command did no longer set the user specified data if the user
specified more than 1 AD field.
We were using the return value of ad_init() to set the number
of AD fields. This did not take into account the number of
existing data fields. By chance this usually returned 1.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
In case a TCP connection should be established with a specific source
IP address (e.g., by calling bind() prior to connect() on the socket),
we have to actually place the address in the outgoing packet.
Signed-off-by: Tobias Frauenschläger <t.frauenschlaeger@me.com>
To prevent failure stopping a ticker node after starting it within the
same ticker_job execution (queued operations), defer the stopping until
after start. This will sequence the operations correctly and prevent
failures.
Signed-off-by: Morten Priess <mtpr@oticon.com>
For config CONFIG_BT_CTLR_CONN_ISO_RELIABILITY_POLICY, set
CIG_Sync_Delay fixed as high as possible, and calculate FT by iteration.
This favors utilizing as much as possible of the Max_Transport_latency,
and spreads out payloads over multiple CIS events (if necessary).
Add exit with cleanup as ll_cig_parameters_commit may fail after
creating new CIG/CIS instances.
Fixes issue #59605.
Fixes EBQ test HCI/CIS/BI-12-C.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Juha Heiskanen