The board has a SPI NOR flash enabled by default but was missing
the "zephyr,flash-controller" in DTS. This prevents the flash
shell sample to compile. So add the DTS entry.
Fixes#26764
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix warnings of the following form:
unit-address and first reg (0x30000) don't match for partition@10000
unit-address and first reg (0x200000) don't match for partition@1F0000
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert to the new GPIO API using logical access, including setting the
GPIO line as active low in the Device Tree source.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As a precursor to the new GPIO API in which GPIO_DIR_OUT isn't a dts
flag move setting of GPIO_DIR_OUT from the dts to explicitly in the
code. We remove setting the flag in intel_s1000_crb.dts as part of this
cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This was always intended to be a bytestring rather than an array, but
full support was missing. Since that has been addressed switch it to
the preferred format.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The JEDEC API defines the hardware page, sector, and block sizes.
Deprecate the Kconfig settings, remove the `erase-size-block` property,
and add `has-be32k` to indicate that 32K-byte erase is supported.
Rework the driver to use the constants instead of configured values.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit adds 'clock-frequency' property to the cpu nodes.
The clock frequency specified in the added property is used
during platform configuration. Examples:
- The SWO logger uses clock frequency to configure SWO output.
- Plenty of platforms need CPU clock specified for their HAL.
- Most of devices with USB needs information about CPU clock
in order to configure USB clock source.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Somehow these were getting generated as `FLASH_foo_BLOCK_SIZE` even
though there's no specification for them in the original yaml. Put them
back until we can figure out what's going on.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Change compatible, move the JEDEC ID from Kconfig to DTS, convert DTS
size from bytes to bits, remove unreferenced DTS properties. Remove DTS
fixups.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Fix the following dtc warnings on S1000:
Warning (simple_bus_reg): /soc/pinmux@81C30: simple-bus unit
address format error, expected "81c30"
Warning (alias_paths): /aliases: aliases property name must
include only lowercase and '-'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patchset introduces partitioning of flash in terms of blocks
(flash page layout) for s1000. This partitioning is currently to
be used for mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Add the codec reset GPIO to intel_s1000_crb's DTS
Update the DTS fixup for intel_s1000_crb accordingly
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Daniel Leung