$ENV{ZEPHYR_BASE} was recently search-replaced with ${ZEPHYR_BASE},
but some CMake code, like usage.cmake, is run by a seperate CMake
build system that does not have access to the CMake variable
ZEPHYR_BASE.
This patch reverts the usage of ${ZEPHYR_BASE} back to use
$ENV{ZEPHYR_BASE} in usage.cmake.
This has been proven to work on both Windows and Linux.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Actually set Zephyr's default DNS server based on the corresponding
DHCP option received. This makes DHCP-based setup Zephyr complete:
now it's possible to connect Zephyr DHCP-enabled system to a typical
router, and it will fully auto-configure to access Internet.
This initial implementation uses just first DNS server address as
returned in DHCP message, it may need to be extended in the future
based on the need.
Signed-off-by: John Andersen <john.s.andersen@intel.com>
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In some cases, we need to initialize DNS servers from a binary
addresses, e.g. in case of DHCP processing. With existing API,
such addresses would need to be converted to strings, just to
be converted back to struct sockaddr in dns_resolve_init().
This is not efficient, and with a number of addresses quite
cumbersome. So instead, allow to pass DNS server either as
strings, or as struct sockaddr's (or both).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This commit refactors the nRF5 radio driver of Bluetooth controller
to use symbolic names for PPIs. It also revisits the Radio hardware
timing constants to align with experimental measurements.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add configuration for zperf sample allowing to build USB dongle with
zperf for testing.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
At the moment CONFIG_SYS_LOG_USB_LEVEL name does not specify that this
is log level for the Device Stack. Make it clear renaming to the
proper name.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove SPI_*_IRQ_PRI from tests and samples.
Using DT to get the *_IRQ_PRI, we can't
override it using Kconfig.
If needed, use a BOARD_NAME.overlay file to
override default values.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This commits adds the "least common denominator" in the
stm32fX.dtsi files and fills the additional SPI nodes
in stm32fXYZ.dtsi files, only for the SOCs where boards
use the additional SPI peripheral.
We could add the rest SPI nodes in the stm32fXYZ.dtsi
files when we add SPI support to other boards.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This reverts commit 5e545e47fb.
This is breaking some tests, needs to be retested with latest master.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The _vector_start was placed before the CONFIG_TEXT_SECTION_OFFSET, thus
adding the offset in the relocated vector table, making the table
invalid when relocated with a non null CONFIG_TEXT_SECTION_OFFSET.
This was tested using MCUboot with a 0x200 offset for the image header.
Fixes: eb48a0a73c ("arm: armv6-m: Support relocating vector table")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reusing the k_thread structure requires a cleanup of all essential
info. We need to remove the ztest_thread information from the timeout_q.
If left untouched, when a tick occurs the thread's delta_ticks_from_prev
would be corrupted. This inturn causes a chain reaction of problems.
Thus once the unit test is completed the timeout_q is scrubbed.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This issuse is found in arch/arc's memory domain api support.
For arc, dwarf-2 is used to keep compatible with synopsys metaware
mdb debugger. However, the gen_kobject_list.py cannot generate the
correct information from dwarf-2, because loc.form's value is
DW_FORM_block1.
If dwarf-4 is adopted, there is no issuse.
Other arch and tools may use dwarf-2 and face the same issuse, so
this commit is created.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Run Kconfig on every reconfigure but with different fragments
depending on the situation.
When .config is missing or when a file from merge_config_file has been
modified use the merge_config_file's as input, otherwise use .config
as input.
This should match the behaviour before kconfiglib.py was introduced
and fixes#5673.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Fix in the prj.conf so the test will also work in boards which
by default compile a BT controller.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The new native Windows development environment no longer relies on MSYS2
or WSL at all. Instead it uses a standard Command Prompt and Windows
native tools. Document the installation and setup process in order to be
able to compile and develop.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
'conf' is part of the zephyr SDK or need to be built and installed in
the path. We now using python for Kconfig processing, so this is not a
strict requirement and we should be able to build without it. If the
binary is not found, just go on with our business.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The offset of the IP header in a received packet depends on the L2
header size. For Ethernet this is 14 bytes which puts the u32 IPv4
addresses on a non-u32 byte boundary. This causes chips that don't
support unaligned access (like the Cortex-M0) to fault.
The fixes in this patch are enough to ping the board and run the
http_server sample.
Signed-off-by: Michael Hope <mlhx@google.com>
Make it possible to run in other posix boards.
By default, if the POSIX board does not define the TICK_IRQ
just run without that part of the test, printing a note.
The place where other POSIX boards should define it, is also
clear, and should be easy to keep those lines free from merge
conflicts in the future.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This test should be blacklisted for any board based
on the POSIX arch, not just the native_posix board
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When checking if a testcase passed or failed, allow there
to be prefixes or postfixes in the line, around
PROJECT EXECUTION SUCCESSFUL/FAILED
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
BT does use a semaphore, which does cause the count of sempahores to
fail, disable BT here to only keep locally created objects.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The jquery provided by Sphinx 1.5.5 has a bug dealing with the
coordinates returned for offset().top for empty <span> tags, generated
by Sphinx for intra-document labels used to create hyperlink anchor
targets. As reported in PR #5591, some browsers (chrome for example)
don't scroll to the right spot in the document when we link to these
intra-document label points. jquery v3.1.2 fixes this. (When Sphinx
updates the jquery included in its release, we can remove our copy that
is overriding the copy installed in the generated output by Sphinx.)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Update tags.sh tool to generate appropriate files to use with cscope and
ctags programs.
Current implementation generates tags for all but samples and it's
possible to filter by architecture.
Signed-off-by: Juan Manuel Torres Palma <j.m.torrespalma@gmail.com>
Due to a chicken-and-egg problem, it's not possible to call
board_runner_args() directly from an application CMakeLists.txt and
have it take effect:
- if the board_runner_args() call appears before including the
boilerplate file, then the function is undefined and an error
occurs.
- if the call appears after including the boilerplate file, then
board_finalize_runner_args() has already been called by the
relevant runner.board.cmake file, so it won't take effect.
Similarly to the way set_conf_file() works, allow applications to
declare additional runner args by checking if they have provided a
macro named app_set_runner_args(), which contains calls to
board_runner_args(). Using a macro means that we can invoke it with
the definition of board_runner_args() in scope.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Sebastian Bøe