When CONFIG_SYS_POWER_DEEP_SLEEP is enabled, spi_qmsi_ss will
keep entering deep sleep because it needs to wait until the
current transfer completes, which blocks the current thread.
The system keeps entering deep sleep again and again and the
transfer will never complete.
Add device_busy_set() to spi_qmsi_ss driver to indicate that
the device is busy and block the system from entering deep
sleep during transaction.
Jira: ZEP-1488
Change-Id: I5a4456933249def93eaa529b30b99d730af74482
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
Enable arc to access the spi controller on I/O fabric.
There are two spi controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the spi controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add spi_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1190
Change-Id: I40a5d423d4b7986a897834d1a3831938005eda6f
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Device sync APIs are actually wrappers for semaphores.
Let's replace them with semaphores.
Jira: ZEP-1411
Change-Id: I02c7cba21d21ff9288e452121e3b7ebb7d251bb4
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch fixes RX overflow error in the k64 SPI driver.
Jira: ZEP-1351
Jira: ZEP-1352
Several circumstances lead to an RX overflow:
The RFOF_RE (RX fifo overflow) must not be set as default.
The flag is only set when rx_buf is available. Also it must
be checked inside spi_k64_isr whether RFOF_RE has been set or not.
If the rx_buf is not available and the incoming data
should be ignored, then MCR_ROOE need to be set.
Since it is not possible to change the MCR register
during the transfer, RX fifo must be emptied
if rx_buf_len < tx_buf_len.
The driver also uses spi_data.xfer_len now,
the variable was already defined. Now, transfers are also
possible if tx_buf_len < rx_buf_len (e.g. read slave device register).
spi_k64_push_data has been adjusted accordingly.
The patch simplifies the handling of interrupts.
The interrupts are also switched off in the event of an error.
The patch also fixes a few coding style issues.
Change-Id: I6ce81f595bb1edbbf2253b6595602896ca652762
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Remove non existent CONFIG_SPI_DEBUG and replace cnt
with DBG_COUNTER_* macros.
Jira: ZEP-1351
Jira: ZEP-1352
Change-Id: I1fba7aaead1ad0b36297b069e5a83e25b7991588
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Clear RX and TX FIFO before starting transfer fixing RX overflow issue
on FRDM K64F board.
Change-Id: I9345a0058a6c7958a6ecf3dc23b99fe7bff18796
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Logging in spi_k64 driver is based on printf-like functions and does
not make sense with syslog which adds additional information like
function name and new line already.
Change-Id: I84a81ebf5c3cc94b311a2e41bdb5f014432d2b09
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use configured init priority same way it is used for other SPI
drivers. Default priority initializes SPI before console hiding
possible errors and debug messages.
Change-Id: Iddc9c783290d852caa8a9385de4ab114f8f7a2e3
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fixes following error:
...
drivers/spi/spi_k64.c:717:86: error: 'cnt' undeclared (first use in
this function)
...
Change-Id: If49fa4838265cd39a6f72eb265388ff7faae9a9e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add function return value check. This was caught by
Coverity.
Coverity-CID: 157124
Change-Id: I93b23325d657dc787300908b9117b6976617fdba
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This commit updates the spi_qmsi_ss driver by adding save/restore
context functionality for power management, using the corresponsing
QMSI APIs.
Jira: ZEP-664
Change-Id: I9e62729f91c4808eb557d8a64c0f10955f5456f3
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This commit updates the spi_qmsi driver by removing the temporary Zephyr
save/restore context implementation and using the new QMSI APIs.
Jira: ZEP-997
Change-Id: I70c6838025253d13d6ebe690ec90dfc1b18bfcea
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
Update the QMSI drop we maintain in Zephyr, and fix the build where
needed:
- QM_SCSS_INT is renamed to QM_INTERRUPT_ROUTER;
- every member of QM_INTERRUPT_ROUTER was renamed as well;
- QM_IRQ_* renamed too, mostly added _INT at the end;
- some isr functions were renamed to keep their names consistent;
- build for x86 needs to define QM_LAKEMONT, as QM_SENSOR was for ARC.
Change-Id: I459029ca0d373f6c831e2bb8ebd52402a55994d1
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Change e4b89571aa renamed the variable
to an undeclared one, without breaking verify but daly breaks.
A local variable of type spi_intel_data was missing on this
function.
Jira: ZEP-1095
Change-Id: Ie410933c2472378d4a6f24d6ca932ac203e3b08c
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Mutable driver state relocated from config_info to driver_info. This
driver supports PCI enumeration. We drop code that attempts to update
irq_num based on PCI enumeration because the interrupt found by PCI
enumeration must always be the same as the statically configured IRQ
number.
Change-Id: I97198ae9603505606a872b07824d6c61688f0ced
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Make pointers to struct config_info const in prepration for a const
config_info.
Change-Id: I1ca9e999840a6ad81dc369b56b1da554f3c1cb49
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Make pointers to struct config_info const in prepration for a const
config_info.
Change-Id: I71bcfa48b31934bc683a344d40bb03f5247bbbec
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Make pointers to struct config_info const in prepration for a const
config_info.
Change-Id: I28789a7f1f26e4a0d499f5a89a567ae8c61eae51
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@gmail.com>
Update the power sample and drivers with the new device driver power
management API using the existing logic
Jira: ZEP-954
Change-Id: Idd94232e458767635973e94e9fc673c01612c1e2
Signed-off-by: Amir Kaplan <amir.kaplan@intel.com>
This patch implements suspend/resume routines which
preserve SPI master 0 and 1 context in SYS_PM_DEEP_SLEEP.
The following parameters are suspended/resumed:
- All non-sticky RW registers for the SPI device which
are not related to a transfer.
- The SPI MASK registers (interrupt routing register).
The suspend/resume functionality is implemented in
the QMSI shim layer as a fast and temporary solution,
it will be removed and migrated to QMSI later.
Change-Id: Ib60317ca41013a3e794820e9c3ef34f35d108209
Signed-off-by: Dragan Cvetic <dragan.cvetic@intel.com>
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Also, SPI 0 isn't specific to Intel, make it a generic message. This patch
only fixes the cosmetics w/o changing undering Kconfig option names.
Change-Id: Ia58f9537c594004a1b5fb8b4af21d7e8b729efb7
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Drivers that implement power management should use the preferred
device_pm_ops method instead.
Change-Id: I337722b1e06afe8508b5c84c00c3542571232e07
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The suspend and resume hooks in the spi_driver_api struct are relics
from before the current power management infrastructure was in place.
The correct way to implement this now is through the device_pm_ops
struct, by way of the DEFINE_DEVICE_PM_OPS and DEVICE_AND_API_INIT_PM
macros, which make the hooks available through a generic mechanism for
all devices, rather than using per-type APIs.
Since the existing spi_suspend() and spi_resume() functions don't check
if the driver_api hooks are NULL, there's now a place holder function
to prevent breaking functionality until the hooks are removed.
Change-Id: I48287c58e9a8649d3e1be7547e3d0d293c84327a
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The suspend and resume hooks in the spi_driver_api struct are relics
from before the current power management infrastructure was in place.
The correct way to implement this now is through the device_pm_ops
struct, by way of the DEFINE_DEVICE_PM_OPS and DEVICE_AND_API_INIT_PM
macros, which make the hooks available through a generic mechanism for
all devices, rather than using per-type APIs.
Since the existing spi_suspend() and spi_resume() functions don't check
if the driver_api hooks are NULL, there's now a place holder function
to prevent breaking functionality until the hooks are removed.
Change-Id: I6a3e3db370860ad46f428d287943b1ca58a80ae1
Signed-off-by: Iván Briano <ivan.briano@intel.com>
QMSI 1.1 Beta is available on Github:
https://github.com/01org/qmsi/releases/tag/v1.1.0-beta
Update the QMSI drop we maintain in Zephyr and
keep the modification to qm_soc_regs.h introduced on commit
6b88a6b945 "ext qmsi: Add USB base and interrupt defines" since
that patch hasn't made into the QMSI 1.1-Beta release in time.
Also, fix the build where needed:
- add hard dependency from qm_i2c to qm_dma
- fix spi_qmsi_ss.c due to new parameter naming
- fix adc_qmsi.c and adc_qmsi_ss.c due to a new parameter
Change-Id: I01388c787f5ee6ee97fece2e42b24a717522207f
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
SPI drivers for K64 is now using system log.
Change-Id: Ifd0d321e2ff84c581261b7cb3a7a4485afbd67f6
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
JIRA: ZEP-311
This will allow the driver to be fiber and task safe
Jira: ZEP-410
Change-Id: I61d3d9e4128bae781f1c86c07af79eb6e43ebeda
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Qiu Peiyang