Update driver to use DTS-generated #defines for port names,
and not obsolete Kconfig variables.
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
L4 write access requires 64 bits alignment
while L4 read access does not require any alignment.
To support specific check according to read/write,erase
a parameter is added to stm32_valid_range.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
L4 have 64 bits write access.
The cast to 64 bits data address in write_dword
requires 3 right shifts on i (byte index) else the
data taken are wrong for i different from 0
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The porting of the TI CC2650 SoC introduces the need to
write a specific configuration area (CCFG) at the end of the
flash. It is read by the bootloader ROM of the SoC.
For now, this is a quick hack and not a generic solution;
similar needs may arise with other hardware.
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Clearing fields in the region descriptor attributes doesn't always have
the expected effect of revoking permissions. In the case of bus master
supervisor mode fields (MxSM), setting to zero actually enables read,
write, and execute access.
When we reworked handling of region descriptor 0, we inadvertently
enabled execution from RAM by clearing the MxSM fields and enabling the
descriptor. This caused samples/mpu_test run to throw a usage fault
instead of an MPU-triggered bus fault.
Fix this by setting all the MxSM fields to 2'b11, which gives supervisor
mode the same access as user mode.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We need to make sure that __NVIC_PRIO_BITS & CONFIG_NUM_IRQ_PRIO_BITS
are set to the same value. Add a simple build time check to ensure
this is the case. This is to catch future cases of issues like
ZEP-2243. This is a stop gap til we resolve ZEP-2262, which covers use
of both __NVIC_PRIO_BITS & CONFIG_NUM_IRQ_PRIO_BITS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch fixes the LOAD_OFFSET calculation to use the actual offset
of the partition. This assumes the reg entry in the DTS for that
partition is in relative offset to the flash base address.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Use globally available find_lsb_set in Zephyr instead of a
custom find first set function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Moving the net_buf_pool objects to a dedicated area lets us access
them by array offset into this area instead of directly by pointer.
This helps reduce the size of net_buf objects by 4 bytes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The net_pkt_split() was incorrectly checking fragA pointer
even before it was allocated.
The unit test is fixed and converted to ztest.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
llvm complains about char* -> u8_t* type conversion.
tests/net/ipv6_fragment/src/main.c:645:52: warning:
passing 'char [11]' to parameter of type 'const u8_t *' (aka
'const unsigned char *') converts between pointers to integer
types with different sign [-Wpointer-sign]
bool written = net_pkt_append_all(pkt, data_len, data,
Jira: ZEP-2274
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
1. Changed _tsc_read() to k_cycles_get_32(). Thus reading the
time stamp will be agnostic of the architecutre used.
2. Changed the variable names from *_tsc to *_time_stamp.
JIRA: ZEP-1426
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Recent changes (69255043, 91f67a13, 84628e8b, fa4a3932) add support
for a partition table in the flash. Add support for this to the nxp
k6x dtsi file. By default, code will occupy the entire flash. By
setting a chosen node in an application, the code can be linked into
one of the partitions. For example, and app could create a
'frdm_k64f.overlay' file at the top of their project with:
/ {
chosen {
zephyr,code-partition = &slot0_partition;
};
};
to place an application in slot 0.
Signed-off-by: David Brown <david.brown@linaro.org>
Misspelled @brief and a couple names were different than
what was in the doxygen comments (generated warnings)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Update the arm.conf to enable CONFIG_FLOAT for the float test and use a
filter on that so we only run/build the test on SoCs/boards that support
floating point hardware.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch changes the config target to use the config-sanitycheck
target. The config-sanitycheck target gets not only the Kconfig
options, but also the DTS generated options.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds a separate target for config-sanitycheck that will
generate a .config-sanitycheck file that contains both Kconfig and DTS
config information.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
- board name olimex_stm32_e407
- CPU STM32F407ZGT6 Cortex M4
- LED/BUTTON support
- Console on USART1 with 8n1 115200 baud
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
gatt-unregister-service can be used to remove the test service at
runtime causing service changed to be indicated:
00:1b:dc:07:31:88 (public)> gatt-unregister-service
[bt] [DBG] gatt_indicate: (0x0011e100) conn 0x0011d880 handle 0x0008
[bt] [DBG] bt_att_req_send: (0x0011e100) conn 0x0011d880 req 0x0011db00
[bt] [DBG] att_send_req: (0x0011e100) req 0x0011db00
Unregistering test vendor service
< ACL Data TX: Handle 3585 flags 0x00 dlen 11
ATT: Handle Value Indication (0x1d) len 6
Handle: 0x0008
Data: 0a001000
> ACL Data RX: Handle 3585 flags 0x02 dlen 5
ATT: Handle Value Confirmation (0x1e) len 0
Jira: ZEP-2225
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
With the introduction of Service Changed support it is now possible to
unregister services at runtime.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds bt_gatt_register_service using bt_gatt_service which contains
the attribute array that is then added to the database saving a pointer
in each and every attribute declared.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GATT is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
GAP is mandatory service and now that the db can only be build
dynamically there is no reason to keep the applications registering it.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes applications able to select the value used for the
GAP appearance attribute.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Removes CONFIG_BLUETOOTH_GATT_DYNAMIC_DB in preparation to the
introduction of bt_gatt_unregister.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In certain cases a response may happen even before number of complete
packets is generated by the controller:
[bt] [DBG] att_req_destroy: (0x0011cfe0) req 0x0011daa0
[bt] [DBG] att_process: (0x0011cfe0)
[bt] [DBG] att_req_sent: (0x0011d780) conn 0x0011d820 att 0x0011d9a0
att->req 0x00000000
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In preparation towards Privacy 1.2, move implementation that
swapped scan response PDU double buffer to same place as
where adv data PDU double buffer is swapped. So that, change
in AdvA in adv data PDU can be reflected in scan response
PDU buffer.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added fix to avoid adv data set function call from
corrupting a ADV_EXT_IND PDU under LE Extended Advertising.
Also, avoid redundant code execution under directed
advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
David B. Kinder