This commit configures ETM/TPIU clock upon startup in case SWO logger
backend is enabled on Atmel SAM E70 SoC.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The Cortex-M7 CPU included in the SAM e70 SoCs has a data cache that
significantly boost the performances. However the SAM GMAC Ethernet
driver is using a scatter-gather technique to exchange data with the
Ethernet driver. This requires the use use of a non-cached memory area.
This is currently not supported on Zephyr, but support for it is being
discussed in PR#11199.
In the meantime, enable the data cache during the SoC initialization,
unless the SAM GMAC Ethernet driver is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The Cortex-M7 CPU included in the SAM e70 SoCs has an instruction cache
that significantly boost the performances. Enable it during the SoC
initialization.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch adds a flash driver for the Atmel SAM E70 SoC. The driver has
been kept simple by considering that the flash is only composed of 8-KiB
blocks. Indeed an area at the beginning of the flash might be erased
with a smaller granularity, and the other blocks can also be erased with
a higher granularity. It also only handles the global read/write
protection, not the 128-KiB lock regions. A write error is returned if
a region is locked.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
All drivers require DTS for their primary SPI settings.
Removing SPI_[0-9]_NAME config option added some more samples changes.
Usage of these options there was anyway not relevant.
Fixes#11064
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The majority of cases of CONFIG_I2C_x_IRQ_PRI should be
DT_I2C_x_IRQ_PRI. So go ahead and fix them up. Only the i2c_nios
driver still uses Kconfig for getting priority.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The majority of bits where already in place, but some minor support
get the driver name from DTS was needed. Now we select HAS_DTS_WDT
for the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to using Kconfig (like other Atmel SAM drivers do) to specify the
pinmux setting for SAMe70 SoCs. Updated the sam_e70_xplained board to
set the default in Kconfig.defconfig instead of via board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds a USB device driver for the USBHS device that can be
found on Atmel SAM E70 SoC family. Only the FIFO mode is supported
(as opposed to DMA). It supports LS, FS and HS modes, but defaults to
FS mode as Zephyr does not fully support HS mode yet.
Tested examples on an Atmel SMART SAM E70 Xplained Board:
* usb/cdc_acm
* usb/hid-mouse
* usb/mass
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This commit introduces CPU_HAS_ARM_MPU and CPU_HAS_NXP_MPU options,
which indicate which flavour of MPU is supported by given SoC family.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Piotr Mienkowski