This patch is to add support for the WaRP7 board which has an i.MX7
Solo SoC.
The Zephyr is running on the Cortex M4 core and the following features
were validated on this board:
* GPIO: User Switch detection and sensors interrupt
* UART: Zephyr console
* I2C: Communication with fxos8700 and fxas21002 sensors
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Move to more generic tracing hooks that can be implemented in different
ways and do not interfere with the kernel.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix in command line parsing common functions, to prevent
a possible segfault when handling string type arguments
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added an entry in drivers/Kconfig for audio
Added an entry in drivers/audio/Kconfig for audio codec
Added an Kconfig file in drivers/audio/ for TLV320DAC
Enabled audio coded in Intel S1000 CRB defconfig
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
PR #8729 removed the old GPIO_NRF5 driver in favor of an
nrfx-based one. The reel_board still references the old one,
causing CI failures.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As reported in issue #9494, BT samples are using the off-chip
UART-based BT controller on 52810. But the on-chip BT controller is
supported on 52810, so this is the reasonable default when BT is
enabled.
This patch enables BT_CTLR by default when BT is enabled.
This resolves#9494.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
I removed GPIO configuration from board files and enabled them
as default in driver Kconfig file. All boards had GPIO ports
enabled that is why I decided to enable it by default.
Power management example was changed to use new driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
This patch adds support for Ethernet in the STM32F2 family of
microcontrollers and enables it for the the Nucleo-F207ZG.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
A design flaw of 'gsource' is that there's no way to require at least
one file to match the glob pattern. This could lead to silent errors.
Switch to a new design, where a plain 'source' is globbing and requires
at least one file to match. A separate 'osource' (optional source)
statement is available for cases where it's okay for a pattern (or plain
filename) to not match any files.
'orsource' combines 'osource' and 'rsource' (relative source).
This commit search-replaces 'gsource' with 'source', but backwards
compatibility with 'gsource' is still maintained by making it an alias
for 'osource' (and by making 'grsource' an alias for 'orsource').
The three Kconfig files arch/{nios2,posix,xtensa}/Kconfig source
arch/{nios2,posix,xtensa}/soc/*/Kconfig, which doesn't match any files.
Use 'osource' for those. The soc/*/Kconfig files seem to be for
additional SoC-specific symbols, only none exist yet on those ARCHes.
Also use 'osource' for the source of $ENV_VAR_BOARD_DIR/Kconfig in
boards/Kconfig, which doesn't exist for all boards.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A bug in the jlink application made it impossible to use OpenSDA
firmware with the mimxrt1052 device name, so we used the generic
Cortex-M7 device name as a workaround. This bug was fixed in jlink
V6.32h (2018-07-05), so now we can use the more specific device name.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface for the nRF52840-DK board (nrf52840_pca10056).
They include the following settings when MODEM_WNCM14A2A is selected:
- UARTE1 pin setup
- DTS / DTS fixup additions for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface instead of ethernet.
They include the following settings when MODEM_WNCM14A2A is selected:
- UART 2 setup
- Avoid ETH_0 setup due to pin conflicts
- DTS addition for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
A few function prototypes were missing in the native_posix
board and its drivers.
Let's add them.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
For each driver/model with command line options.
Move its code for the board file into the driver/model file.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Allow command line arguments to be registered dynamically
instead of being statically defined.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Some drivers or tests need to execute some code before Zephyr is
booted, dynamically register command line arguments, etc.
For this purpose, we generalize the NATIVE_EXIT_TASK to also
provide hooks to run a function at a given point during the startup
of native_posix.
Also, test/boards/native_posix/exit_tasks is generalized to cover
this new functionality.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The board config has been verified to boot with serial console
on the Atom version of the UP Squared board. So the references
to Pentium/Celeron can be removed. Moreover, add some notes on
BIOS settings, as it may change the MMIO addresses for various
IP blocks.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add the necessary bits to enable the I2C controllers on
the UP Squared board. Only the ones exposed through the HAT
connector(s) are enabled by default.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This enables the cc3220sf_launchxl to automatically
reconnect to the last good known access point (AP).
This method avoids the need to:
- perform a wifi scan for access points on bootup (saving power);
- include hard-coded SSID/passwords in the wifi application.
- include the wifi shell in the wifi application.
- rely on more complex provisioning methods;
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Enable the support for the 3 I2C buses of the STM32F723E-DISCO board,
connected respectively to the WM8994, the Arduino V3/STMOD+ and the
touch panel.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For native_posix:
Added the option to control the speed of the simualated time vs
the real(host) time.
Added a model of a real time clock with an API.
In the documentation we clarify the relationship between simulated
time and real time, and include documentaion of this new RTC.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Until now, command line options switches which matched the
begining of other options with argumentes needed to be listed
after those. After this fix this is not neccessary anymore.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Let the HW events which would have executed right at the
stop-at time happen, as this produces a more intuitive runtime.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Due to bug #9054 this boards is being disable from sanitycheck
temporarily.
Revert when the board is fixed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Mark this board as simulation board to be run with nsimdrv.
See documentation for how to get nsimdrv.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Wayne Ren