90 lines
4.0 KiB
Plaintext
90 lines
4.0 KiB
Plaintext
/**
|
|
@page RCC_ClockConfig RCC Clock Config example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file RCC/RCC_ClockConfig/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the RCC Clock Config example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Configuration of the system clock (SYSCLK) and modification of the clock settings in Run mode, using the RCC HAL API.
|
|
|
|
In this example, after startup SYSCLK is configured to the max frequency using the PLL with
|
|
HSI48 as clock source, the User push-button (connected to EXTI_Line0) will be
|
|
used to change the PLL source:
|
|
- from HSI to HSI48
|
|
- from HSI48 to to HSI
|
|
|
|
Each time the User push-button is pressed; EXTI_Line0 interrupt is generated and in the ISR
|
|
the PLL oscillator source is checked using __HAL_RCC_GET_PLL_OSCSOURCE() macro:
|
|
|
|
|
|
- If the HSI oscillator is selected as PLL source, the following steps will be followed to switch
|
|
the PLL source to HSI48 oscillator:
|
|
a- Switch the system clock source to HSI to allow modification of the PLL configuration
|
|
b- Enable HSI48 Oscillator, select it as PLL source and finally activate the PLL
|
|
c- Select the PLL as system clock source and configure the HCLK and PCLK1 clocks dividers
|
|
d- Disable the HSI oscillator (optional, if the HSI is no more needed by the application)
|
|
|
|
- If the HSI48 oscillator is selected as PLL source, the following steps will be followed to switch
|
|
the PLL source to HSI oscillator:
|
|
a- Switch the system clock source to HSI48 to allow modification of the PLL configuration
|
|
b- Enable HSI Oscillator, select it as PLL source and finally activate the PLL
|
|
c- Select the PLL as system clock source and configure the HCLK and PCLK1 clocks dividers
|
|
d- Disable the HSI48 oscillator (optional, if the HSI48 is no more needed by the application)
|
|
|
|
In this example the SYSCLK is outputted on the MCO1 pin(PA.08).
|
|
|
|
LED3 is toggled with a timing defined by the HAL_Delay() API.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- RCC/RCC_ClockConfig/Inc/stm32f0xx_hal_conf.h HAL configuration file
|
|
- RCC/RCC_ClockConfig/Inc/stm32f0xx_it.h Interrupt handlers header file
|
|
- RCC/RCC_ClockConfig/Inc/main.h Header for main.c module
|
|
- RCC/RCC_ClockConfig/Src/stm32f0xx_it.c Interrupt handlers
|
|
- RCC/RCC_ClockConfig/Src/main.c Main program
|
|
- RCC/RCC_ClockConfig/Src/system_stm32f0xx.c STM32F0xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F072xB devices.
|
|
|
|
- This example has been tested with STM32F072B-Discovery RevC
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|