MCP794XX supports digital trimming that periodically adds or subtracts
clock cycles, resulting in small adjustments in the internal timing.
This way inaccuracies of clock source can be compensated.
This commit adds option to set the trimming register for MCP794XX.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds configuration option CONFIG_MCP794XX_DATETIME_UTC.
If set, the datetime is stored in UTC instead of local time. The
default value is kept at local time to keep backwards compatibility
with devices currently using the RTC.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Embedded flash can have user signature area on SAMv7. This is a 512
bytes large page whose data are not erased by asserting ERASE pin or by
software ERASE command.
This commit adds arch to board interface for this area. It is possible
to perform read, write and erase operation. SAMV7_USER_SIGNATURE option
has to be set in the configuration.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This temporary fix is just to unblock CI errors:
```
Configuration/Tool: imx93-evk/bootloader
...
aarch64-none-elf-ld: region `ocram' overflowed by 88 bytes
```
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
The definition of nxsched_process_cpuload_ticks uses clock_t, which is
portable across uint32_t and uint64_t timers, and works if CONFIG_SYSTEM_TIME64 is
defined.
DAC driver uses CONFIG_DAC_FIFOSIZE, but this is not configurable
from Kconfig. This adds the missing option and allows to set DAC
FIFO size from the configuration.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
only when first time change state can hold WFI for enough time thresh,
allow second time goto target state,
suitable for the case when wakeup from sleep too slow, etc.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
By default U(S)ART clocks are enabled in sam_lowput.c but
configuration check from sam_config.h may override USART configuration
and prevent clocks from been enabled.
This commit fix inconsistency in U(S)ART pinmux and clock configuration
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
In "psock_send_eventhandler",when retransmit count bigger TCP_MAXRTX nuttx will set release wrb. But before this it will also set "conn->tx_unacked = 0" if we only retransmit one packet(conn->tx_unacked == sent),and In func "tcp_timer" only "conn->tx_unacked > 0" will close the tcp conn. So app will never close if nuttx retransmit over max timers.
Signed-off-by: meijian <meijian@xiaomi.com>
This is to fix issue in [this log](https://github.com/apache/nuttx/actions/runs/9173629303/job/25222879619):
```
Configuration/Tool: esp32c3-generic/twai esp32c6-devkitm/twai esp32c6-devkitc/twai esp32h2-devkit/twai
Error: common/espressif/esp_twai.c:242:7: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
```
Signed-off-by: Yanfeng Liu <yfliu2008@qq.com>
Search and replace ARCH_BOOT_EL3 with more generic
ARCH_ARM64_EXCEPTION_LEVEL that holds the EL level
in an integer variable.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides a capable bootloader that may be run from OCRAM.
The OCRAM contains regions that are always zero, so the linker
file avoids those with best effort.
iMX9 infrastructure expects:
- 0x20480000 (Start of OCRAM, AHAB)
- 0x2049a000 (NuttX or SPL)
- 0x204e0000 (ARM Trustzone, not used)
When started from SD-card, the offsets are:
- 0x1f000 with AHAB
- 0xa000 without AHAB
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Value 1021, when read from ICC_IAR0_EL1 means:
"The GIC returns this value in response to a read of ICC_IAR0_EL1 or ICC_HPPIR0_EL1 at EL3,
to indicate that the interrupt being acknowledged is one which is expected to be handled at
Non-secure EL1 or EL2. This INTID is only returned when the PE is executing at EL3 using
AArch64 state, or when the PE is executing in AArch32 state in Monitor mode."
When this happens:
- FIQ is fired on group0
- IRQ is pending at group1
So simply check and handle the interrupt. In short, this provides interrupt support for
EL3.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides means to run NuttX completely in EL3. This may
be useful with NuttX based bootloaders that are executed from
OCRAM. Instead of SPL/U-boot combo, NuttX may replace SPL
completely.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Huang Qi