Refine find_ptirq_entry by hashing instead of walk each of the PTIRQ entries one by one.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong<eddie.dong@Intel.com>
RTVM (with lapic PT) boots hang when maxcpus is
assigned a value less than the CPU number configured
in hypervisor.
In this case, vlapic_state(per VM) is left in TRANSITION
state after BSP boot, which blocks interupts to be injected
to this UOS.
Tracked-On: #4803
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Li, Fei <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There's no need to look up MSI ptirq entry by virtual SID any more since the MSI
ptirq entry would be removed before the device is assigned to a VM.
Now the logic of MSI interrupt remap could simplify as:
1. Add the MSI interrupt remap first;
2. If step is already done, just do the remap part.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong<eddie.dong@Intel.com>
Reviewed-by: Grandhi, Sainath <sainath.grandhi@intel.com>
If HV relocation is enabled, either ACRN efi-stub or GRUB relocates
hypervisor image above HPA 256MB, thus we put hvlog and ramoops buffer
under 256MB to avoid conflict with hypervisor owned address.
This patch hardcodes these addresses:
0xa00000 - 0xdfffff: 4MiB for ramoops buffer
0xe00000 - 0xffffff: 2MiB for hvlog buffer
However, user can customize them to other addresses as long as it's under
256MB, available in host e820, and SOS bootarg "nokaslr" is not specified.
If HV relocation is disabled, need to make sure that these buffer
addresses are not between HV_RAM_START and HV_RAM_START + HV_RAM_SIZE.
Tracked-On: #4760
Signed-off-by: Zide Chen <zide.chen@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
For post-launched VMs, the configured CPU affinity could be different
from the actual running CPU affinity. This new field acrn_vm->cpu_affinity
recognizes this difference so that it's possible that CREATE_VM
hypercall won't overwrite the configured CPU afifnity.
Change name cpu_affinity_bitmap in acrn_vm_config to cpu_affinity.
This is read-only in run time, never overwritten by acrn-dm.
Remove vm_config->vcpu_num, which means the number of vCPUs of the
configured CPU affinity. This is not to be confused with the actual
running vCPU number: vm->hw.created_vcpus.
Changed get_vm_bsp_pcpu_id() to get_configured_bsp_pcpu_id() for less
confusion.
Tracked-On: #4616
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
ACRN syncs PIR to vIRR in the software in cases the Posted
Interrupt notification happens while the pCPU is in root mode.
Sync can be achieved by processor hardware by sending a
posted interrupt notiification vector.
This patch sends a self-IPI, if there are interrupts pending in PIR,
which is serviced by the logical processor at the next
VMEnter
Tracked-On: #4777
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
CDP is an extension of CAT. It enables isolation and separate prioritization of
code and data fetches to the L2 or L3 cache in a software configurable manner,
depending on hardware support.
This commit adds a Kconfig switch "CDP_ENABLED" which depends on "RDT_ENABLED".
CDP will be enabled if the capability available and "CDP_ENABLED" is selected.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
Reviewed-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This commit makes some RDT code cleanup, mainling including:
- remove the clos_mask and mba_delay validation check in setup_res_clos_msr(), the check will be done in pre-build;
- rename platform_clos_num to valid_clos_num, which is set as the minimal clos_mas of all enabled RDT resouces;
- init the platform_clos_array in the res_cap_info[] definition;
- remove the unnecessary return values and return value check.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
A RDT resource could be CAT or MBA, so only one of struct rdt_cache and struct rdt_membw
would be used at a time. They should be a union.
This commit merge struct rdt_cache and struct rdt_membw in to a union res.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
Reviewed-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com
#AC should be normally enabled for slpitlock detection, however,
community developers may want to run ACRN on buggy system.
In this case, CONFIG_ENFORCE_TURNOFF_AC can be used to turn off the
#AC, to let the guest run without #AC.
Tracked-On: #4765
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The virtual MSI information could be included in ptirq_remapping_info structrue,
there's no need to pass another input paramater for this puepose. So we could
remove the ptirq_msi_info input.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
We look up PTIRQ entru only by SID. So _by_sid could removed.
And refine function name to verb-obj style.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
For return value of local_gpa2hpa, either INVALID_HPA or NULL
means the EPT walking failure. Current code only take care of
NULL return and leave INVALID_HPA as correct case.
In some cases (if guest page table is filled with invalid memory
address), it could crash ACRN from guest.
Add INVALID_HPA return check as well.
Also add @pre assumptions for some gpa2hpa usages.
Tracked-On: #4730
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
When boot ACRN hypervisor from grub multiboot, HV will be loaded at
CONFIG_HV_RAM_START since relocation is not supported in grub
multiboot1. The CONFIG_HV_RAM_SIZE in industry scenario will take
~330MB(0x14000000), unfortunately the efi memmap on NUC7i7DNB is
truncated at 0x6dba2000 although it is still usable from 0x6dba2000. So
from grub point of view, it could not find a continuous memory from
0x6000000 to load industry scenario. Per efi memmap, there is a big
memory area available from 0x40400000, so put CONFIG_HV_RAM_START to
0x41000000 is much safe for NUC7i7DNB.
Tracked-On: #4641
Signed-off-by: Victor Sun <victor.sun@intel.com>
The original stack used in CPU booting is: ld_bss_end + 4KB;
which could be out of the RAM size limit defined in link_ram file.
So add a specific stack space in link_ram file, and used in
CPU booting.
Tracked-On: #4738
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
According to SDM Vol 3, Chap 10.4.7.2 Local APIC State After It Has Been Software Disabled,
The mask bits for all the LVT entries are set when the local APIC has been software disabled.
So there's no need to mask all the LVT entries one by one.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Currently the vcpu_affinity[] array fixes the vCPU to pCPU mapping.
While the new cpu_affinity_bitmap doesn't explicitly sepcify this
mapping, instead, it implicitly assumes that vCPU0 maps to the pCPU
with lowest pCPU ID, vCPU1 maps to the second lowest pCPU ID, and
so on.
This makes it possible for post-launched VM to run vCPUs on a subset of
these pCPUs only, and not all of them.
acrn-dm may launch post-launched VMs with the current approach: indicate
VM UUID and hypervisor launches all VCPUs from the PCPUs that are masked
in cpu_affinity_bitmap.
Also acrn-dm can choose to launch the VM on a subset of PCPUs that is
defined in cpu_affinity_bitmap. In this way, acrn-dm must specify the
subset of PCPUs in the CREATE_VM hypercall.
Additionally, with this change, a guest's vcpu_num can be easily calculated
from cpu_affinity_bitmap, so don't assign vcpu_num in vm_configuration.c.
Tracked-On: #4616
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add FADT table support to support guest S5 setting.
According to ACPI 6.3 Spec, OSPM must ignored the DSDT and FACS fields if them're zero.
However, Linux kernel seems not to abide by the protocol, it will check DSDT still.
So add an empty DSDT to meet it.
Tracked-On: #4623
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Remove sdc2 scenario since the VM launch requirement under this scenario
could be satisfied by industry scenario now;
Tracked-On: #4661
Signed-off-by: Victor Sun <victor.sun@intel.com>
In industry scenario, hypervisor will support 1 post-launched RT VM
and 1 post-launched kata VM and up to 5 post-launched standard VMs;
Tracked-On: #4661
Signed-off-by: Victor Sun <victor.sun@intel.com>
The patch enables CPU sharing feature by default, the default scheduler is
set to SCHED_BVT;
Tracked-On: #4661
Signed-off-by: Victor Sun <victor.sun@intel.com>
The current logic puts hpa2 above GPA 4G always, which is incorrect. Need
to set gpa start of hpa2 right after hpa1 when hpa1 size is less then 2G;
Tracked-On: #4458
Signed-off-by: Victor Sun <victor.sun@intel.com>
On most board the MCFG base is set to 0xe0000000, so modify this value in
platform_acpi_info.h for generic boards;
The description of ACPI_PARSE_ENABLED is modified also to match its usage.
Tracked-On: #4157
Signed-off-by: Victor Sun <victor.sun@intel.com>
CONFIG_MAX_KATA_VM_NUM is a scenario specific configuration, so it is better
to put the MACRO in scenario folder directly, to instead the Kconfig item in
Kconfig file which should work for all scenarios;
Tracked-On: #4616
Signed-off-by: Victor Sun <victor.sun@intel.com>
Basicly ACRN scenario is a configuration name for specific usage. By giving
scenario name ACRN will load corresponding VM configurations to build the
hypervisor. But customer might have their own scenario name, change the
scenario type from choice to string is friendly to them since Kconfig source
file change will not be needed.
With this change, CONFIG_$(SCENARIO) will not exist in kconfig file and will
be instead of CONFIG_SCENARIO, so the Makefile need to be changed accordingly;
Tracked-On: #4616
Signed-off-by: Victor Sun <victor.sun@intel.com>
Currently the vm uuid and severity is initilized separately in
vm_config struct, developer need to take care both items carefuly
otherwise hypervisor would have trouble with the configurations.
Given the vm loader_order/uuid and severity are binded tightly, the
patch merged these tree settings in one macro so that developer will
have a simple interface to configure in vm_config struct.
Tracked-On: #4616
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
If CPU has MSR_TEST_CTL, show an emulaued one to VCPU
Tracked-On: #4496
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Yan, Like <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
If CPU support rise #AC for Splitlock Access, then enable this
feature at each CPU.
Tracked-On: #4496
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Yan, Like <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When the destination of an atomic memory operation located in 2
cache lines, it is called a Splitlock Access. LOCK# bus signal is
asserted for splitlock access which may lead to long latency. #AC
for Splitlock Access is a CPU feature, it allows rise alignment
check exception #AC(0) instead of asserting LOCK#, that is helpful
to detect Splitlock Access.
This feature is enumerated by MSR(0xcf) IA32_CORE_CAPABILITIES[bit5]
Add helper function:
bool has_core_cap(uint32_t bitmask)
Tracked-On: #4496
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Yan, Like <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
remove unnecessary state check and
add pre-condition for vcpu APIs.
Tracked-On: #4320
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
check the vm state in hypercall api,
add pre-condition for vm api.
Tracked-On: #4320
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
now it will call pause_vm in shutdown_vm,
move it out from shutdown_vm to reduce coupling.
Tracked-On: #4320
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch wrapps a common function to initialize physical
CPU for the second phase to reduce redundant code.
Tracked-On: #861
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
ACRN disables Snoop Control in VT-d DMAR engines for simplifing the
implementation. Also, since the snoop behavior of PCIE transactions
can be controlled by guest drivers, some devices may take the advantage
of the NO_SNOOP_ATTRIBUTE of PCIE transactions for better performance
when snoop is not needed. No matter ACRN enables or disables Snoop
Control, the DMA operations of passthrough devices behave correctly
from guests' point of view.
This patch is used to clean all the snoop related code.
Tracked-On: #4509
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
Due to the fact that i915 iommu doesn't support snoop, hence it can't
access memory when the SNOOP bit of Secondary Level page PTE (SL-PTE)
is set, this will cause many undefined issues such as invisible cursor
in WaaG etc.
Current hv design uses EPT as Scondary Leval Page for iommu, and this
patch removes the codes of setting SNOOP bit in both EPT-PTE and SL-PTE
to avoid errors.
And according to SDM 28.2.2, the SNOOP bit (11th bit) will be ignored
by EPT, so it will not affect the CPU address translation.
Tracked-On: #4509
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
Waag will send NMIs to all its cores during reboot. But currently,
NMI cannot be injected to vcpu which is in HLT state.
To fix the problem, need to wakeup target vcpu, and inject NMI through
interrupt-window.
Tracked-On: #4620
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Align the implementation to SDM Vol.3 4.1.1.
Also this patch fixed a bug that doesn't check paging status first
in some cpu mode.
Tracked-On: #4628
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Currently vlapic_build_id() uses vcpu_id to retrieve the lapic_id
per_cpu variable:
vlapic_id = per_cpu(lapic_id, vcpu->vcpu_id);
SOS vcpu_id may not equal to pcpu_id, and in that case it runs into
problems. For example, if any pre-launched VMs are launched on PCPUs
whose IDs are smaller than any PCPU IDs that are used by SOS.
This patch fixes the issue and simplify the code to create or get
vapic_id by:
- assign vapic_id in create_vlapic(), which now takes pcpu_id as input
argument, and save it in the new field: vlapic->vapic_id, which will
never be changed.
- simplify vlapic_get_apicid() by returning te saved vapid_id directly.
- remove vlapic_build_id().
- vlapic_init() is only called once, merge it into vlapic_create().
Tracked-On: #4268
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Maintain a per-pCPU array of vCPUs (struct acrn_vcpu *vcpu_array[CONFIG_MAX_VM_NUM]),
one VM cannot have multiple vCPUs share one pcpu, so we can utilize this property
and use the containing VM's vm_id as the index to the vCPU array:
In create_vcpu(), we simply do:
per_cpu(vcpu_array, pcpu_id)[vm->vm_id] = vcpu;
In offline_vcpu():
per_cpu(vcpu_array, pcpuid_from_vcpu(vcpu))[vcpu->vm->vm_id] = NULL;
so basically we use the containing VM's vm_id as the index to the vCPU array,
as well as the index of posted interrupt IRQ/vector pair that are assigned
to this vCPU:
0: first vCPU and first posted interrupt IRQs/vector pair
(POSTED_INTR_IRQ/POSTED_INTR_VECTOR)
...
CONFIG_MAX_VM_NUM-1: last vCPU and last posted interrupt IRQs/vector pair
((POSTED_INTR_IRQ + CONFIG_MAX_VM_NUM - 1U)/(POSTED_INTR_VECTOR + CONFIG_MAX_VM_NUM - 1U)
In the posted interrupt handler, it will do the following:
Translate the IRQ into a zero based index of where the vCPU
is located in the vCPU list for current pCPU. Once the
vCPU is found, we wake up the waiting thread and record
this request as ACRN_REQUEST_EVENT
Tracked-On: #4506
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@Intel.com>
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
This is a preparation patch for adding support for VT-d PI
related vCPU scheduling.
ACRN does not support vCPU migration, one vCPU always runs on
the same pCPU, so PI's ndst is never changed after startup.
VCPUs of a VM won’t share same pCPU. So the maximum possible number
of VCPUs that can run on a pCPU is CONFIG_MAX_VM_NUM.
Allocate unique Activation Notification Vectors (ANV) for each vCPU
that belongs to the same pCPU, the ANVs need only be unique within each
pCPU, not across all vCPUs. This reduces # of pre-allocated ANVs for
posted interrupts to CONFIG_MAX_VM_NUM, and enables ACRN to avoid
switching between active and wake-up vector values in the posted
interrupt descriptor on vCPU scheduling state changes.
A total of CONFIG_MAX_VM_NUM consecutive IRQs/vectors are reserved
for posted interrupts use.
The code first initializes vcpu->arch.pid.control.bits.nv dynamically
(will be added in subsequent patch), the other code shall use
vcpu->arch.pid.control.bits.nv instead of the hard-coded notification vectors.
Rename some functions:
apicv_post_intr --> apicv_trigger_pi_anv
posted_intr_notification --> handle_pi_notification
setup_posted_intr_notification --> setup_pi_notification
Tracked-On: #4506
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@Intel.com>
Fill in posted interrupt fields (vector, pda, etc) and set mode to 1 to
enable VT-d PI (posted mode) for this ptdev.
If intr_src->pi_vcpu is 0, fall back to use the remapped mode.
Tracked-On: #4506
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@Intel.com>
Given the vcpumask, check if the IRQ is single destination
and return the destination vCPU if so, the address of associated PI
descriptor for this vCPU can then be passed to dmar_assign_irte() to
set up the posted interrupt IRTE for this device.
For fixed mode interrupt delivery, all vCPUs listed in vcpumask should
service the interrupt requested. But VT-d PI cannot support multicast/broadcast
IRQs, it only supports single CPU destination. So the number of vCPUs
shall be 1 in order to handle IRQ in posted mode for this device.
Add pid_paddr to struct intr_source. If platform_caps.pi is true and
the IRQ is single-destination, pass the physical address of the destination
vCPU's PID to ptirq_build_physical_msi and dmar_assign_irte
Tracked-On: #4506
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@Intel.com>
Add platform_caps.c to maintain platform related information
Set platform_caps.pi to true if all iommus are posted interrupt capable, false
otherwise
If lapic passthru is not configured and platform_caps.pi is true, the vm
may be able to use posted interrupt for a ptdev, if the ptdev's IRQ is
single-destination
Tracked-On: #4506
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@Intel.com>
PCI devices with 64-bit MMIO BARs and requiring large MMIO space
can be assigned with physical address range at the very high end of
platform supported physical address space.
This patch uses the board info for 64-bit MMIO window as programmed
by BIOS and constructs 1G page tables for the same.
As ACRN uses identity mapping from Linear to Physical address space
physical addresses upto 48 bit or 256TB can be supported.
Tracked-On: #4586
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add 64-bit MMIO window related MACROs to the supported board files
in the hypervisor source code.
Tracked-On: #4586
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Mingqiang Chi