When the physical USB device is disconnected before DM's emulation
is ready, the virtual connection state is not cleared properly. This
will cause the DM refuse to do emulation for future physical connection.
This patch clears those states mentioned above and hence fix the issue.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1367
When USB hub is disconnected, its connection status is not cleared
in the DM, this defect will cause the related assigned port could
not be used any more.
This patch is used fix this issue.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1365
Previous implementation binds libusb (in other words: usbfs) with
native device when DM receives the Enable Slot command. But according
to xHCI spec 4.6.5, the binding relationship is decided when the
Address Device command is received, so this implementation is not
consistent with hardware behaviors.
And this incompatible could induce following issue. When two or more
USB devices are connected at the same time, eg, connecting two devices
before Guest OS is booted, the virtual slot id may bind to wrong root
hub port.
This patch will do the binding when Address Device command is received
and related issues will be fixed.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1366
According to xHCI spec, the Stop Endpoint command should execute
no matter the endpoint is in halted state or not, but current
implementation just refuse do the command and return error to
Guest OS. It is wrong and this patch is used to fix it.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1366
One additional command parameter is added for virtio-net to support
vhost net. The command line for vhost net is as follows:
-s n,virtio-net,tap_xxx,vhost
Tracked-On: #1329
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
vhost proxy interacts with vhost kernel thru vhost char dev. Internal
interfaces are implemented based on ioctls of vhost char dev in this
patch.
Tracked-On: #1329
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
There are 2 eventfds for one virtqueue, one is for kick and the other
is for notify. eventfd used for kick is associated with a PIO/MMIO
region. eventfd used for notify is associated with a MSIx/INTx. The
eventfd pair is registered to VHM thru VHM char dev.
VHM irqfd currently only support MSIx. If INTx is used, vhost proxy
uses mevent to poll the call fd from vhost then inject interrupt to
guest.
Tracked-On: #1329
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
vhost kernel driver needs the information of memory mapping between
GPA and the virtual addresses in device model process. This is
required for virtqueue related operations. This patch gets memory
mapping information from vmctx then conveys to vhost.
Tracked-On: #1329
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
vhost_vq related interfaces are implemented in this patch. They are
vhost_vq_init/vhost_vq_deinit/vhost_vq_start/vhost_vq_stop.
Tracked-On: #1329
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch adds the vhost support to the device model virtio. A vhost
proxy is implemented based on the virtio framework and vhost char dev.
Key data structures and external interfaces are implemented in this
patch.
Tracked-On: #1329
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Some virtio ring structures and virtio feature bits are using the
same name/definition as those in kernel header files(linux/
virtio_ring.h, linux/virtio_config.h). Kernel header files must
be included to perform ioctls to support vhost. There are
compiling errors due to duplicated definitions. In this patch
the following renamings are done:
VRING_DESC_F_NEXT -> ACRN_VRING_DESC_F_NEXT
VRING_DESC_F_WRITE -> ACRN_VRING_DESC_F_WRITE
VRING_DESC_F_INDIRECT -> ACRN_VRING_DESC_F_INDIRECT
VRING_AVAIL_F_NO_INTERRUPT -> ACRN_VRING_AVAIL_F_NO_INTERRUPT
VRING_USED_F_NO_NOTIFY -> ACRN_VRING_USED_F_NO_NOTIFY
VIRTIO_F_NOTIFY_ON_EMPTY -> ACRN_VIRTIO_F_NOTIFY_ON_EMPTY
VIRTIO_RING_F_INDIRECT_DESC -> ACRN_VIRTIO_RING_F_INDIRECT_DESC
VIRTIO_RING_F_EVENT_IDX -> ACRN_VIRTIO_RING_F_EVENT_IDX
VIRTIO_F_VERSION_1 -> ACRN_VIRTIO_F_VERSION_1
vring_avail -> virtio_vring_avail
vring_used -> virtio_vring_used
vring_size -> virtio_vring_size
Tracked-On: #1329
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Netmap/vale attempts to speed up network communication by bypassing the
TCP/IP network stack, which requires patching the physical NIC driver so
that applications developed based on netmap can interact directly with
the physical NIC driver. It may make sense for some specific scenarios
which requres very high bandwith (10Gb/s or 100Gb/s), we can even put up
with the complexity and compatibility introduced by this techology.
However for ACRN, a virtualization solution for IoT, there is no need to
support this backend. For 1Gb NICs or below, the VBS-U/tap solution
can already achieve near-native bandwidth. To keep simplicity and
improve compatibility, remove the netmap/vale support in dm.
Tracked-On: #1313
Signed-off-by: Jie Deng <jie.deng@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
CAVS audio driver depends on the NHLT table to get topology info.
Enable NHLT table in DM for audio passthrough.
Also increase the size reserved for NHLT in ACPI table from 2048B to 2560B.
Tracked-On: #1284
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
This is temperory workaround for DM crash when doing fastboot
reboot. In fastboot, it will disable USB host functionality by
disable device respsone to one PCI bar. While DM code just release
the bar in this case. Which break the reboot functionality.
The workaround is to remove the assert to avoid DM abort. This is
safe because reboot will remove all memory range registered.
We will have offiical fixing later.
Tracked-On: #1277
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
USB device is connected before UOS is booted up, this scenario is
called 'cold plug' for easy to refer.
Under 'cold plug' situation, the libusb will not report 'connect'
event to device model, hence UOS will not discover 'cold plugged'
device.
This patch add support to fix this issue.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1242
Flat Mode for hub emulation means DM emulates USB devices under hub but
hide hub itself. Under this design the Guest OS cannot see any emulated
hub. So in the perspective of Guest OS, all the emulated devices are
under root hub.
This patch is used to enable feature as mentioned above. And please NOTE,
it is the initial version of hub flat Mode hub emulation, there are one
limitation: only one physical hub is supported. If second physical hub is
connected, the connect and disconnect behavior in second hub may affect
the function of first emulated hub.
The USB HUB device model should be the final long term solution, but it is
very complex. Use flat mode HUB emulation as the short term solution first
to support some USB touch devices which integrated internal HUB.
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Reviewed-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1243
In current code, when read/write msix table, it first handle the case
the offset is in pba range when msix talbe and pba share the same bar.
But the code didn't add the condition whether pba bar equals msix table
bar. It will cause problems for the passthrugh devices,whose pba and msix
table don't share the same bar.
Tracked-On: #1209
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
This patch implements RTC feature that UOS can set RTC wakeup timer
to IOC firmware with a specific time before enter S3/S5. IOC mediator
also needs to indicate RTC wakeup reason to UOS after exit S3/S5.
Tracked-On: #1213
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
In the current implementation sigev_notify is configured as
SIGEV_THREAD. When timer expires an async thread is created and
the registered timer callback is called in the context of this
thread. vrtc_update_timer will access the global data vrtc. There
is a race condition that vrtc is freed when deinit and then a timer
expires. In this case vrtc_update_timer will access a freed buffer
which causes problem such as heap corruption and segment fault.
In this patch signal model is used when timer is created. The signal
is masked and a signalfd is used to poll on it with mevent. This avoids
the race condition.
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Tracked-On: #1185
if some pci devices behind gvt got failures when initlizing at init_pci(), gvt
instance have no chance to be destroied even acrn-dm exits.
NOTE: this patch can not work standalone, a following patch to kernel
side(643d40961cf: "vhm: init client->kthread_exit true") is requied as well,
otherwise it will stucks during destroying gvt instance.
Tracked-On: #1141
Signed-off-by: Li Zhijian <zhijianli88@163.com>
Unmap ptdev BAR when deinit to comply with native system, who zap out
all pre-allocated BARs.
Tracked-On: #1146
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1. In default prescaler, the wdt clock is 1 KHz for a 20-bit counter,
which means approximate 1 second for 10 bits;
2. the default reset timer in seconds need to left shift 10 bits to
represent the value that set to i6300esb register;
Tracked-On: #1142
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
To align with the configuration of the HOST tool, the SW masters
are organized in slices of 8 masters each.
The slice is also the minimal unit to allocate the SW masters for
each UOS.
The patch is to update the parameter checking function.
Tracked-On: #1138
Signed-off-by: Zhi Jin <zhi.jin@intel.com>
Reviewed-by: Chen Gang <gang.c.chen@intel.com>
This patch fixes an issue that CBC signal channel
is inactive after SOS resuming, it leads to IOC mediator
cannot transfer any signals between UOS and SOS. So IOC
mediator sends the open channel command to activate CBC
signal channel after resuming.
Tracked-On: #1115
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The whole vmctx will be cleared during cold reset.
cmos data should not be cleared during cold reset.
Move cmos data out of vmctx.
Tracked-On: #1118
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
This patch is used to fix a potential issue resulted from typo.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
CMOS offset from 0x20 to 0x9F is used to store rpmb key information.
vsbl loader will init vrpmb key in CMOS when boot/reboot.
vsbl loader will not init vrpmb key during S3 resume.
vsbl will read vrpmb key via CMOS interface.
After reading, the key value is cleared in CMOS. So the key can only be
read once until next boot.
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
When reset VBS-K status should be set to VIRTIO_DEV_INIT_SUCCESS
because at the time the char dev of VBS-K is still opened and
when set_status callback is called later, it depends on
VIRTIO_DEV_INIT_SUCCESS to resume.
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
A new ioctl is introduced in VBS-K to issue reset command to kernel
VBS-K driver. This is used to support VBS-K S3. When FE enters S3
reset command is sent to device model. Backend driver in device model
should use this ioctl to inform the VBS-K drvier in kernel.
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
RPMB frontend driver in UOS kernel has fixed unstable issue,
which requires BE for update as well. E.g. structure adjustment,
definition modification and so on.
Signed-off-by: Deng Wei <wei.a.deng@intel.com>
Signed-off-by: Huang Yang <yang.huang@intel.com>
Acked-by: Zhu Bing <bing.zhu@intel.com>
This patch enable the support for SOS S3 from the perspective
of USB xHCI.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The xHCI emulation greatly depends on the user space library libusb
which is based on the usbfs module in Linux kernel. The libusb will
bind usbfs to physical USB device which makes hardware control over
libusb in user space possible.
The pci_xhci_dev_create is called in pci_xhci_native_usb_dev_conn_cb
which is a callback function triggered by physical USB device plugging.
This function will bind the physical USB device to usbfs in SOS, which
we depend to create the communication between UOS xHCI driver with
physical USB device.
This design will fail if the reconnection happened in the SOS, which
will bind class driver to the physical USB device instead of usbfs,
hence the libusb device handle in DM is invalid.
Currently, the native S3 will disable the vbus for all xHCI ports and
re-drive during S3 resume. This behavior cause native USB driver unbind
the usbfs and bind to related class driver, then made the DM lost
control and failed to continue emulation.
To fix this issue, place the pci_xhci_dev_create in the function
pci_xhci_cmd_enable_slot. According to the xHCI spec 4.5.3 Figure 10,
the UOS always send Enable Slot command when a device is attached or
recovered from errors (by Disable Slot command). So every time the SOS
can't resuming normally or some unexpected disconnection happens, this
desigen will always survive by Disable Slot and Enable Slot command
series from UOS xHCI driver.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Replace 'native_assign_ports' with 'port_map_tbl' to be more accurate
for the role of this variable plays.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The variable native_assign_ports in struct pci_xhci_vdev is used
to record wether certain root hub port in SOS is assigned to UOS.
The logic uses zero to express 'not assigned' and nonzero to express
'assigned'. In this patch, use macro to replace number to express
better.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Currently the maximum number of bus and port for xHCI are
both set to 255, it is theoretically possible but in fact
not neccessary. This patch changes those two values to be
more proper: 4 buses and 20 ports.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current design cannot get physical USB device information without
the creation of pci_xhci_dev_emu. This brings some difficulties in
certain situations, hence struct usb_native_devinfo is introduced
to describe neccessary information to solve this trouble.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
PORTSC (Port Status and Control Register) register play a very
important role in USB sub-system. This patch is used to refine
related manipulation functions.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current DM design use two variables to do the indexing of xHCI
Event Ring: er_enq_idx and er_events_cnt. They are members of
the struct pci_xhci_rtsregs.
In UOS, during the process of xHCI resuming, the xHCI driver
will restore the ERSTBA (Event Ring Segment Table Base Address)
register to be the value before suspending. And at this point,
the old DM implementation will set both er_enq_idx and
er_events_cnt to be zero, so the DM will access the Event Ring
from the start position in the buffer. But at the same time the
UOS xHCI driver still wants to access the old position in the
Event Ring before suspending, which will result of unexpected
errors.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This device model is to configure the virtual IPU PCI device.
In order to execute this DM the lauch script needs to add
virtio-ipu as parameter to acrn-dm
For e.g. -s 21,virtio-ipu
Signed-off-by: Bandi,Kushal <kushal.bandi@intel.com>
Randomness sourced from /dev/random which does not block
once it has been seeded at bootup and you will always get
something when you read from that file. This is true on
Freebsd but unfortunately things are not the same on Linux.
Most cases, you can't read anything from /dev/random especially
on current acrn platform which lacking random events.
virtio_rnd inherted from freebsd doesn't work anymore.
This patch makes virtio_rnd working on Linux based SOS. It uses
blocking IO to sevice the front-end random driver and delays the
read operation into a new thread to avoid blocking the main
notify thread.
Signed-off-by: Jie Deng <jie.deng@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
1. support "writeback" and "writethru" mode toggling for virtio-blk
conditionally. When starting DM with "writethru" parameter in
virtio-blk, guest OS could not toggle cache mode. When starting DM
with "writeback" parameter in virtio-blk, guest OS could toggle
cache mode.
------------------------------
DM cmdline | toggle support
------------+-----------------
writeback | yes
writethru | no
------------------------------
2. To toggle cache mode, run below command in guest OS:
echo "write back" > /sys/devices/xxx/vdx/cache_type
OR
echo "write through" > /sys/devices/xxx/vdx/cache_type
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
currently, each virtio device has their own virtio_ops implementation.
Take virtio-blk for example:
static struct virtio_ops virtio_blk_ops = {
"virtio_blk",
1,
sizeof(struct virtio_blk_config),
virtio_blk_reset,
virtio_blk_notify,
virtio_blk_cfgread,
virtio_blk_cfgwrite,
NULL,
NULL,
VIRTIO_BLK_S_HOSTCAPS,
};
If start DM with two virtio-blk, this global variable will be
assigined to two virtio-blk instances. Changing hv_caps for one
instance will affect others. But different instances may need
different capabilities.
To support this requirement, we suggest to move hv_caps to
virtio_base structure, and each instance can return their own
capabilities.
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
In writethru mode, guest storage write are reported completed only
when the data has been written to physical storage.
In writeback mode, guest storage write are reported completed when
data is placed in SOS page cache. Needs to be flushed to the
physical storage.
USAGE:
-s x,virtio-blk,<filepath>,writeback
-s x,virtio-blk,<filepath>,writethru
The default mode is *writethru*
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
With latest FW, ethernet/wifi BDF changes from 3:0.0/4:0.0 to
2:0.0/3:0.0.
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch resolves one arcn-dm crash issue when rebooting UOS.
The rootcause is that uart releases unopened backend tty.
One reproduced case is that the board does not support IOC but IOC
feature is enabled in the acrn-dm. After rebooting UOS, crash will
happen.
NOTE: This issue is not related to IOC, it also can be reproduced
with NON-IOC scenario. Just set one invalid PTY to the lpc, then
this issue should be reproduced.
We need re-visit the whole policy for such scenario in future.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
mevent is added only if uart backend fd refers TTY in uart_opentty.
So we should only delete mevent if uart backend fd refers TTY in uart_closetty.
This issue can be reproduced by below steps
1) acrnd starts UOS
2) run poweroff command in UOS
3) crash happens
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
We do:
- pause target vm
- suspend all virtual devices
- wait for resume notification
- resume all virtual devices
- reset target vm
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When guest enter/exit S3, we need to do
1. stop watchdog timer when guest enter S3 to avoid watchdog
timer reset guest when guest is in S3 state.
2. reset watchdog timer when guest exit from S3.
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch adds new signals about parking brake and Hvac in the signal
definition and signal whitelist.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch resolves IOC mediator deinit function is blocked due to IOC mediator
core thread enters into sleep by epoll_wait, then pthread_join cannot return.
Trigger an event to wakeup core thread when IOC mediator deinit is invoked.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Enable isochronous transfer to support related USB devices
Change-Id: Id9fe0714e937fafc47de090ba6d349713cbe1b8b
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
In the process of implementation for USB isochronous transfer, the
timeout (100ms) is not enough for Plantronics USB headset. So pass
longer timeout (300ms) to function libusb_control_transfer will
make USB headset of Plantronics work.
This change only results a longer execution time in ENUMERATION process
for few devices like Plantronics USB headset which need more time to do
its internal operations. For most USB devices, time less than 100ms are
enough to complete the execution of libusb_control_transfer. So basically
it will not affect the whole system performance.
In the long term, a better solution (eg: async control transfer) will be
introduced to replace current implementation.
Change-Id: I380e0cc337ec5741b1e4ce989abacce826b7dde4
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
BCD code is USB Specification Release Number in Binaray-Coded
Decimal. Add some BCD codes for some USB devices.
Change-Id: I40f04ef2ebaf5b0da554ff8f432415e8e3cebe01
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Add microframe index register support, which is an important timing
component for isochronous transport.
Change-Id: I615664275b539cfb713d7795edd3f213b0302b92
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Handle the LIBUSB_TRANSFER_STALL error comes from libusb.
Change-Id: Id6911e9aaffafb256def5265a0ed9778b147d99a
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current ring buffer processing logic assumes every transaction
will be submited to physical device before next transaction
coming. So it use two states 0 (free) and 1 (used) to represent
the state of every data block in the ring buffer. With the help
of the two state, the ring buffer could accept and process data
normally.
But this logic is not proper for ISOC transfer, which generally
submits many transactions even none of them arrive the physical
device. So this patch uses three values to represent the state
of data block in the ring buffer:
USB_XFER_BLK_FREE: this block could be filled with new data;
USB_XFER_BLK_HANDLING: this block is submited to physical device
but response from device is still not received;
USB_XFER_BLK_HANDLED: this block has been processed by physical
device.
The new logic will do different things for each state, which will
make the ISOC transfer work successfully.
Change-Id: I5559cae24c739633289742d64dd51751797b81a7
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The xHCI speed emulation is not right, which will cause failure
during enumeration of certain USB device. This patch is used to
fix it.
Change-Id: I2d996298983882ed6921a75a10dec9e8684a393e
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Refine the logic of usb interface state transition.
The libusb uses two pair of APIs to deal with usb interface:
1. libusb_claim_interface & libusb_detach_kernel_driver;
2. libusb_release_interface & libusb_attach_kernel_driver.
The calling sequences of those APIs are very important, so this
patch add some error handling code to make this process more
robust.
Change-Id: I0f7950aae806dee9a21f16cc293f51609eede0d8
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch is used to add support for USB 3.0 devices. Currently
USB 3.0 disk is supported and tested successfully.
Change-Id: I3fbfbe9c28bc4b14af0417104f8fa822f9758908
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
There are many 'short packet' warnings in the UOS kernel dmesg output,
which are result from bad short packet identification algorithm. This
patch is used to fix it.
Change-Id: Idfa0b87fc96893b80d5c9fe8dab4db35aa5bfe84
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Original code will reset the whole USB device when xHCI Reset
Endpoint command is received, this behavior is not right. This
patch is used to fix it.
And according to xhci spec 4.6.8, if the endpoint is not in the
halted state, xHC should reject to execute this command and the
Context State Error should be returned. This patch also add this
logic.
Change-Id: I55a5918148d82d103fb3eb27d582f9676f9f61d3
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Mainly change the logs for transfer submission and completion,
which are very important parts in USB emulation code.
Change-Id: I4e04f1426e164ca3693e70946ed51380201e49ee
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch correct the USB request type which set wrong direction in
original code. It caused these important usb control transfer packets
send to phsical USB devices via libusb_control_transfer instead of
calling standard libusb APIs, likes libusb_set_configuration. From
libusb document, this is not the correct way:
"You should always use this function rather than formulating your own
SET_CONFIGURATION control request. This is because the underlying
operating system needs to know when such changes happen."
Change-Id: I7a6aade326220bee3b685086584920dacd37f87c
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This function add high level reset_vdev function. Which is
implemented to call deinit/init pairing to emulate the virtual
device reset operation.
This patch also add the system reset which keep the UOS RAM
content functionality to DM.
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Guest has erquirement to support system/full reboot and S3. Which could
trigger different reset path in guest
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
We should keep variable name in function declaration. It makes
things clearer and easier to be understood.
Signed-off-by: Jie Deng <jie.deng@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
There has one new DRD driver followed usb role framework which is just
upstreamed to Linux community. This patch updates the xHCI DM to be
compatible with it. DM DRD code follows DRD spec to implement and make
it more reasonable.
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Reviewed-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
For dedicated xHCI extended capability, it need set corresponding PCI VID/PID.
This patch sets the Intel Apollo Lake platform PCI VID/PID for DRD
capability which will be checked for enabling DRD fucntion in new DRD
driver. Besides, this patch refines the PCI VID/PID related code.
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Reviewed-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
6300esb has bit in its register to show whether the watchdog
timeout is hit.
This patch adds this bit support. So the guest could query
whether last reset is triggered by watchdog reset.
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Reviewed-by: Cao Minggui <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Tested-by: Binbin Wu <binbin.wu@intel.com>
The lpc dm causes that UOS can't boot if the parameters are set incorrectly,
it is not friendly to users.
This patch optimizes the lpc error handle flow. UOS always can boot successfully
whatever the lpc settings are.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
When XSDT is created by DM, if audio passthru is enabled for
audio device (0:e:0), an entry is added in XSDT that references
the NHLT table. With this fix, NHLT appears in the kernel boot
log for ACPI and entry can be seen in /sys/firmware/acpi/tables/NHLT.
Signed-off-by: Madeeha Javed <madeeha_javed@mentor.com>
An immediate reset or power down will cause a loss of write content.
The cause is the data write to disk is at cache within a short
time window before it's synced to storage media.
An explicit fsync() forces to sync the data to storage to prevent
the data loss of such immediate reset.
Signed-off-by: Huang Yang <yang.huang@intel.com>
Signed-off-by: duminx <minx.du@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
WIFI dev has no FLR, so 'reset' in sysfs calls secondary bus reset,
which cause PCI configuration mess(all FF) then passthrough failure.
To fix it, this patch makes no reset before passthrough by default,
until append this option.
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Current option of removing vGSI capability is global, which exposes
vIOAPIC link for all ptdev even only one need this. This patch makes
it as ptdev local option to lower the system level impact. To keep
vGSI for MSI capable ptdev, just explicitly append ",keep_gsi" in
option list, like "-s 14,passthru,0/e/0,keep_gsi"
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Previously, either rnd->fd or vbs_k->fd isn't be closed in some cases.
this patch will close them in time.
V2: fix vbs_k->fd leak as well
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
- hardcode the devices' GSI info based on the platform
- reject the passthrough if the following requirement is not met
all the PCI devices that are sharing the same GSI should be assigned
to same VM to avoid physical GSI sharing between multiple VMs.
v4 -> v5
* Move the gsi_dev_mapping_tables definition in a separate file
* Add the GSI info that might be used by GPIO
* Update the HW name
v3 - > v4
* Refine the format of raw data to improve the readability
* Remove the redundant code when adding the new dev into the gsi
sharing group
v2 -> v3
* Add the MSI/MSI-x capability check
Do not add the device which supports MSI/MSI-x to the GSI sharing
group.
v1 -> v2
* Update the GSI raw data based on SBL
* Free the resources when gsi sharing violation occurs
* Move the MACRO PCI_BDF(b, d, f) to pci_core.h since passthrough.c
and gsi_sharing.c are both using it
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
Reviewed-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The device model is a userspace application on SOS to config the
PCI devices for the UOS. Audio mediator device model is to config
the virtual audio PCI device.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
When enabling GPU passthru for guest, stolen memory needs to be
disabled. This change disables stolen memory in passthru mode.
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Reviewed-by: Gong Zhipeng <zhipeng.gong@intel.com>
To enable GPU passthru, BAR2 allocation had problems when the allocation
is above the 4GB memory.This change is to accomodate the 256MB aperture
allocation in BAR2 to a more managable address.
v2: changed the MEMBASE64 address instead of increasing the mem_size.
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Reviewed-by: Gong Zhipeng <zhipeng.gong@intel.com>
This patch implements VM monitor operations including stop/suspend/resume.
For other VM monitor operations(pause/unpause/query), IOC mediator would not
register callbacks for them since there is no requirements from VM Manager.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
acrn-dm runs to segmentation fault when failed to create VMs with
improper parameters.
If vdevs failed to be created, they are still be freed in deinit(),
and dereference the null pointers leads to segfault.
Signed-off-by: Xinyun Liu <xinyun.liu@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Some APIs of Openssl 1.0 are deprecated in Openssl 1.1+.
Two different API implementations are adaptable to both
Openssl 1.1- and 1.1+.
Fixes: #305
Signed-off-by: Huang Yang <yang.huang@intel.com>
Signed-off-by: Du Min <minx.du@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch fix some potential crash issues, like wild
pointers access, buffer overflow and etc.
Change-Id: Iddd8e1820da426adc6b9b4d9da9e44017d9f365c
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
With current implementation:
vm_init_vdevs only handles the negative error code, while passthru_init
returns positive error code when error occurs.
This causes unexpected dm crash since the real error is not being
handled properly.
What this patch does:
Change the error code to be negative value in passthru_init because it
is common in Linux kernel to return negative value when error occurs.
v2 -> v3
* add more comments about the reason to convert the return value
v1 -> v2:
* add a wrapper API to convert the error returned from pci_system_init
to the ERROR we defined in DM
* use the defined errno as the return value rather than -1
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The Intel Trace Hub (aka. North Peak, NPK) is a trace aggregator for
Software, Firmware, and Hardware. On the virtualization platform, it
can be used to output the traces from SOS/UOS/Hypervisor/FW together
with unified timestamps.
There are 2 software visible MMIO space in the npk pci device. One is
the CSR which maps the configuration registers, and the other is the
STMR which is organized as many Masters, and used to send the traces.
Each Master has a fixed number of Channels, which is 128 on GP. Each
channel occupies 64B, so the offset of each Master is 8K (64B*128).
Here is the detailed layout of STMR:
M=NPK_SW_MSTR_STP (1024 on GP)
+-------------------+
| m[M],c[C-1] |
Base(M,C-1) +-------------------+
| ... |
+-------------------+
| m[M],c[0] |
Base(M,0) +-------------------+
| ... |
+-------------------+
| m[i+1],c[1] |
Base(i+1,1) +-------------------+
| m[i+1],c[0] |
Base(i+1,0) +-------------------+
| ... |
+-------------------+
| m[i],c[1] |
Base(i,1)=SW_BAR+0x40 +-------------------+
| m[i],c[0] | 64B
Base(i,0)=SW_BAR +-------------------+
i=NPK_SW_MSTR_STRT (256 on GP)
CSR and STMR are treated differently in npk virtualization because:
1. CSR configuration should come from just one OS, instead of each OS.
In our case, it should come from SOS.
2. For performance and timing concern, the traces from each OS should
be written to STMR directly.
Based on these, the npk virtualization is implemented in this way:
1. The physical CSR is owned by SOS, and dm/npk emulates a software
one for the UOS, to keep the npk driver on UOS unchanged. Some CSR
initial values are configured to make the UOS npk driver think it
is working on a real npk. The CSR configuration from UOS is ignored
by dm, and it will not bring any side-effect. Because traces are the
only things needed from UOS, the location to send traces to and the
trace format are not affected by the CSR configuration.
2. Part of the physical STMR will be reserved for the SOS, and the
others will be passed through to the UOS, so that the UOS can write
the traces to the MMIO space directly.
A parameter is needed to indicate the offset and size of the Masters
to pass through to the UOS. For example, "-s 0:2,npk,512/256", there
are 256 Masters from #768 (256+512, #256 is the starting Master for
software tracing) passed through to the UOS.
CSR STMR
SOS: +--------------+ +----------------------------------+
| physical CSR | | Reserved for SOS | |
+--------------+ +----------------------------------+
UOS: +--------------+ +---------------+
| sw CSR by dm | | mapped to UOS |
+--------------+ +---------------+
Here is an overall flow about how it works.
1. System boots up, and the npk driver on SOS is loaded.
2. The dm is launched with parameters to enable npk virtualization.
3. The dm/npk sets up a bar for CSR, and some values are initialized
based on the parameters, for example, the total number of Masters for
the UOS.
4. The dm/npk sets up a bar for STMR, and maps part of the physical
STMR to it with an offset, according to the parameters.
5. The UOS boots up, and the native npk driver on the UOS is loaded.
6. Enable the traces from UOS, and the traces are written directly to
STMR, but not output by npk for now.
7. Enable the npk output on SOS, and now the traces are output by npk
to the selected target.
8. If the memory is the selected target, the traces can be retrieved
from memory on SOS, after stopping the traces.
Signed-off-by: Zhi Jin <zhi.jin@intel.com>
Reviewed-by: Zhang Di <di.zhang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
To avoid PTY device symbol link failure due to non-exist directory passed from
parameter. Add check_dir function to check the directory and create it if not
exist.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In virtio_heci struct there have deiniting/pending_reset/resetting
variables. All these variables represent the status of virtio heci devices.
Change them into one enum type variable for vheci status.
Signed-off-by: Long Liu <long.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
NHLT table is used by some audio driver for topology data, but current
default audio driver doens't depend on it. Disable it by default due
to possible boot failure with different SOS firmware.
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Jason Chen CJ