118 lines
2.0 KiB
Plaintext
118 lines
2.0 KiB
Plaintext
/*
|
|
* Copyright (c) 2018 Seitz & Associates
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/f3/stm32f302X8.dtsi>
|
|
#include <st/f3/stm32f302r(6-8)tx-pinctrl.dtsi>
|
|
#include "arduino_r3_connector.dtsi"
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32F302R8-NUCLEO board";
|
|
compatible = "st,stm32f302r8-nucleo";
|
|
|
|
chosen {
|
|
zephyr,console = &usart2;
|
|
zephyr,shell-uart = &usart2;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
green_led_2: led_2 {
|
|
gpios = <&gpiob 13 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD2";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button {
|
|
label = "User";
|
|
gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &green_led_2;
|
|
sw0 = &user_button;
|
|
};
|
|
};
|
|
|
|
&clk_hse {
|
|
hse-bypass;
|
|
clock-frequency = <DT_FREQ_M(8)>; /* STLink 8MHz clock */
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
prediv = <1>;
|
|
mul = <9>;
|
|
clocks = <&clk_hse>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rcc {
|
|
clocks = <&pll>;
|
|
clock-frequency = <DT_FREQ_M(72)>;
|
|
ahb-prescaler = <1>;
|
|
apb1-prescaler = <2>;
|
|
apb2-prescaler = <1>;
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb9>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&spi2 {
|
|
pinctrl-0 = <&spi2_sck_pb13 &spi2_miso_pb14 &spi2_mosi_pb15>;
|
|
pinctrl-names = "default";
|
|
cs-gpios = <&gpiob 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart1 {
|
|
pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa10>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
&usart2 {
|
|
pinctrl-0 = <&usart2_tx_pa2 &usart2_rx_pa3>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
&usart3 {
|
|
pinctrl-0 = <&usart3_tx_pc10 &usart3_rx_pc11>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&timers2 {
|
|
status = "okay";
|
|
|
|
pwm2: pwm {
|
|
status = "okay";
|
|
pinctrl-0 = <&tim2_ch1_pa0>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|
|
|
|
&adc1 {
|
|
pinctrl-0 = <&adc1_in1_pa0>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|