227 lines
7.1 KiB
ReStructuredText
227 lines
7.1 KiB
ReStructuredText
.. _nrf52840dk_nrf52840:
|
|
|
|
nRF52840 DK
|
|
###########
|
|
|
|
Overview
|
|
********
|
|
|
|
The nRF52840 Development Kit (PCA10056) hardware provides support for the
|
|
Nordic Semiconductor nRF52840 ARM Cortex-M4F CPU and the following devices:
|
|
|
|
* :abbr:`ADC (Analog to Digital Converter)`
|
|
* CLOCK
|
|
* FLASH
|
|
* :abbr:`GPIO (General Purpose Input Output)`
|
|
* :abbr:`I2C (Inter-Integrated Circuit)`
|
|
* :abbr:`MPU (Memory Protection Unit)`
|
|
* :abbr:`NVIC (Nested Vectored Interrupt Controller)`
|
|
* :abbr:`PWM (Pulse Width Modulation)`
|
|
* RADIO (Bluetooth Low Energy and 802.15.4)
|
|
* :abbr:`RTC (nRF RTC System Clock)`
|
|
* Segger RTT (RTT Console)
|
|
* :abbr:`SPI (Serial Peripheral Interface)`
|
|
* :abbr:`UART (Universal asynchronous receiver-transmitter)`
|
|
* :abbr:`USB (Universal Serial Bus)`
|
|
* :abbr:`WDT (Watchdog Timer)`
|
|
|
|
.. figure:: img/nrf52840dk_nrf52840.jpg
|
|
:align: center
|
|
:alt: nRF52840 DK
|
|
|
|
nRF52840 DK (Credit: Nordic Semiconductor)
|
|
|
|
More information about the board can be found at the `nRF52840 DK website`_.
|
|
The `Nordic Semiconductor Infocenter`_ contains the processor's information
|
|
and the datasheet.
|
|
|
|
|
|
Hardware
|
|
********
|
|
|
|
nRF52840 DK has two external oscillators. The frequency of the slow clock
|
|
is 32.768 kHz. The frequency of the main clock is 32 MHz.
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The nrf52840dk_nrf52840 board configuration supports the following
|
|
hardware features:
|
|
|
|
+-----------+------------+----------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+======================+
|
|
| ADC | on-chip | adc |
|
|
+-----------+------------+----------------------+
|
|
| CLOCK | on-chip | clock_control |
|
|
+-----------+------------+----------------------+
|
|
| FLASH | on-chip | flash |
|
|
+-----------+------------+----------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+----------------------+
|
|
| I2C(M) | on-chip | i2c |
|
|
+-----------+------------+----------------------+
|
|
| MPU | on-chip | arch/arm |
|
|
+-----------+------------+----------------------+
|
|
| NVIC | on-chip | arch/arm |
|
|
+-----------+------------+----------------------+
|
|
| PWM | on-chip | pwm |
|
|
+-----------+------------+----------------------+
|
|
| RADIO | on-chip | Bluetooth, |
|
|
| | | ieee802154 |
|
|
+-----------+------------+----------------------+
|
|
| RTC | on-chip | system clock |
|
|
+-----------+------------+----------------------+
|
|
| RTT | Segger | console |
|
|
+-----------+------------+----------------------+
|
|
| SPI(M/S) | on-chip | spi |
|
|
+-----------+------------+----------------------+
|
|
| UART | on-chip | serial |
|
|
+-----------+------------+----------------------+
|
|
| USB | on-chip | usb |
|
|
+-----------+------------+----------------------+
|
|
| WDT | on-chip | watchdog |
|
|
+-----------+------------+----------------------+
|
|
|
|
Other hardware features have not been enabled yet for this board.
|
|
See `nRF52840 DK website`_ and `Nordic Semiconductor Infocenter`_
|
|
for a complete list of nRF52840 Development Kit board hardware features.
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
LED
|
|
---
|
|
|
|
* LED1 (green) = P0.13
|
|
* LED2 (green) = P0.14
|
|
* LED3 (green) = P0.15
|
|
* LED4 (green) = P0.16
|
|
|
|
Push buttons
|
|
------------
|
|
|
|
* BUTTON1 = SW1 = P0.11
|
|
* BUTTON2 = SW2 = P0.12
|
|
* BUTTON3 = SW3 = P0.24
|
|
* BUTTON4 = SW4 = P0.25
|
|
* BOOT = SW5 = boot/reset
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Applications for the ``nrf52840dk_nrf52840`` board configuration can be
|
|
built, flashed, and debugged in the usual way. See
|
|
:ref:`build_an_application` and :ref:`application_run` for more details on
|
|
building and running.
|
|
|
|
Flashing
|
|
========
|
|
|
|
Follow the instructions in the :ref:`nordic_segger` page to install
|
|
and configure all the necessary software. Further information can be
|
|
found in :ref:`nordic_segger_flashing`. Then build and flash
|
|
applications as usual (see :ref:`build_an_application` and
|
|
:ref:`application_run` for more details).
|
|
|
|
Here is an example for the :ref:`hello_world` application.
|
|
|
|
First, run your favorite terminal program to listen for output.
|
|
|
|
.. code-block:: console
|
|
|
|
$ minicom -D <tty_device> -b 115200
|
|
|
|
Replace :code:`<tty_device>` with the port where the board nRF52840 DK
|
|
can be found. For example, under Linux, :code:`/dev/ttyACM0`.
|
|
|
|
Then build and flash the application in the usual way.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: nrf52840dk_nrf52840
|
|
:goals: build flash
|
|
|
|
Debugging
|
|
=========
|
|
|
|
Refer to the :ref:`nordic_segger` page to learn about debugging Nordic boards with a
|
|
Segger IC.
|
|
|
|
|
|
Testing the LEDs and buttons in the nRF52840 DK
|
|
***********************************************
|
|
|
|
There are 2 samples that allow you to test that the buttons (switches) and LEDs on
|
|
the board are working properly with Zephyr:
|
|
|
|
.. code-block:: console
|
|
|
|
samples/basic/blinky
|
|
samples/basic/button
|
|
|
|
You can build and flash the examples to make sure Zephyr is running correctly on
|
|
your board. The button and LED definitions can be found in
|
|
:zephyr_file:`boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840.dts`.
|
|
|
|
Using UART1
|
|
***********
|
|
|
|
The following approach can be used when an application needs to use
|
|
more than one UART for connecting peripheral devices:
|
|
|
|
1. Add devicetree overlay file to the main directory of your application:
|
|
|
|
.. code-block:: devicetree
|
|
|
|
&pinctrl {
|
|
uart1_default: uart1_default {
|
|
group1 {
|
|
psels = <NRF_PSEL(UART_TX, 0, 14)>,
|
|
<NRF_PSEL(UART_RX, 0, 16)>;
|
|
};
|
|
};
|
|
/* required if CONFIG_PM_DEVICE=y */
|
|
uart1_sleep: uart1_sleep {
|
|
group1 {
|
|
psels = <NRF_PSEL(UART_TX, 0, 14)>,
|
|
<NRF_PSEL(UART_RX, 0, 16)>;
|
|
low-power-enable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
compatible = "nordic,nrf-uarte";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
pinctrl-0 = <&uart1_default>;
|
|
pinctrl-1 = <&uart1_sleep>;
|
|
pinctrl-names = "default", "sleep";
|
|
};
|
|
|
|
In the overlay file above, pin P0.16 is used for RX and P0.14 is used for TX
|
|
|
|
2. Use the UART1 as ``DEVICE_DT_GET(DT_NODELABEL(uart1))``
|
|
|
|
See :ref:`set-devicetree-overlays` for further details.
|
|
|
|
Selecting the pins
|
|
==================
|
|
|
|
Pins can be configured in the board pinctrl file. To see the available mappings,
|
|
open the `nRF52840 Product Specification`_, chapter 7 'Hardware and Layout'.
|
|
In the table 7.1.1 'aQFN73 ball assignments' select the pins marked
|
|
'General purpose I/O'. Note that pins marked as 'low frequency I/O only' can only be used
|
|
in under-10KHz applications. They are not suitable for 115200 speed of UART.
|
|
|
|
References
|
|
**********
|
|
|
|
.. target-notes::
|
|
|
|
.. _nRF52840 DK website: https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52840-DK
|
|
.. _Nordic Semiconductor Infocenter: https://infocenter.nordicsemi.com
|
|
.. _J-Link Software and documentation pack: https://www.segger.com/jlink-software.html
|
|
.. _nRF52840 Product Specification: http://infocenter.nordicsemi.com/pdf/nRF52840_PS_v1.0.pdf
|