127 lines
3.1 KiB
C
127 lines
3.1 KiB
C
/*
|
|
*
|
|
* Copyright (c) 2017 Linaro Limited.
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
|
|
#include <soc.h>
|
|
#include <stm32_ll_bus.h>
|
|
#include <stm32_ll_pwr.h>
|
|
#include <stm32_ll_rcc.h>
|
|
#include <stm32_ll_utils.h>
|
|
#include <zephyr/drivers/clock_control.h>
|
|
#include <zephyr/sys/util.h>
|
|
#include <zephyr/drivers/clock_control/stm32_clock_control.h>
|
|
#include "clock_stm32_ll_common.h"
|
|
|
|
#if defined(STM32_PLL_ENABLED)
|
|
|
|
/**
|
|
* @brief Return PLL source
|
|
*/
|
|
__unused
|
|
static uint32_t get_pll_source(void)
|
|
{
|
|
if (IS_ENABLED(STM32_PLL_SRC_HSI)) {
|
|
return LL_RCC_PLLSOURCE_HSI;
|
|
} else if (IS_ENABLED(STM32_PLL_SRC_HSE)) {
|
|
return LL_RCC_PLLSOURCE_HSE;
|
|
}
|
|
|
|
__ASSERT(0, "Invalid source");
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* @brief get the pll source frequency
|
|
*/
|
|
__unused
|
|
uint32_t get_pllsrc_frequency(void)
|
|
{
|
|
if (IS_ENABLED(STM32_PLL_SRC_HSI)) {
|
|
return STM32_HSI_FREQ;
|
|
} else if (IS_ENABLED(STM32_PLL_SRC_HSE)) {
|
|
return STM32_HSE_FREQ;
|
|
}
|
|
|
|
__ASSERT(0, "Invalid source");
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* @brief Set up pll configuration
|
|
*/
|
|
__unused
|
|
void config_pll_sysclock(void)
|
|
{
|
|
LL_RCC_PLL_ConfigDomain_SYS(get_pll_source(),
|
|
pllm(STM32_PLL_M_DIVISOR),
|
|
STM32_PLL_N_MULTIPLIER,
|
|
pllp(STM32_PLL_P_DIVISOR));
|
|
|
|
#if defined(CONFIG_SOC_SERIES_STM32F7X)
|
|
/* Assuming we stay on Power Scale default value: Power Scale 1 */
|
|
if (CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC > 180000000) {
|
|
/* Enable the PLL (PLLON) before setting overdrive. Skipping the PLL
|
|
* locking phase since the system will be stalled during the switch
|
|
* (ODSW) but the PLL clock system will be running during the locking
|
|
* phase. See reference manual (RM0431) §4.1.4 Voltage regulator
|
|
* Sub section: Entering Over-drive mode.
|
|
*/
|
|
LL_RCC_PLL_Enable();
|
|
|
|
/* Set Overdrive if needed before configuring the Flash Latency */
|
|
LL_PWR_EnableOverDriveMode();
|
|
while (LL_PWR_IsActiveFlag_OD() != 1) {
|
|
/* Wait for OverDrive mode ready */
|
|
}
|
|
LL_PWR_EnableOverDriveSwitching();
|
|
while (LL_PWR_IsActiveFlag_ODSW() != 1) {
|
|
/* Wait for OverDrive switch ready */
|
|
}
|
|
|
|
/* The PLL could still not be locked when returning to the caller
|
|
* function. But the caller doesn't know we've turned on the PLL
|
|
* for the overdrive function. The caller will try to turn on the PLL
|
|
* And start waiting for the PLL locking phase to complete.
|
|
*/
|
|
}
|
|
#endif /* CONFIG_SOC_SERIES_STM32F7X */
|
|
}
|
|
|
|
#endif /* defined(STM32_PLL_ENABLED) */
|
|
|
|
#ifdef STM32_PLLI2S_ENABLED
|
|
|
|
/**
|
|
* @brief Set up PLL I2S configuration
|
|
*/
|
|
__unused
|
|
void config_plli2s(void)
|
|
{
|
|
#if DT_HAS_COMPAT_STATUS_OKAY(st_stm32f4_plli2s_clock)
|
|
LL_RCC_PLLI2S_ConfigDomain_I2S(get_pll_source(),
|
|
pllm(STM32_PLLI2S_M_DIVISOR),
|
|
STM32_PLLI2S_N_MULTIPLIER,
|
|
plli2sr(STM32_PLLI2S_R_DIVISOR));
|
|
#elif DT_HAS_COMPAT_STATUS_OKAY(st_stm32f412_plli2s_clock)
|
|
LL_RCC_PLL_ConfigDomain_I2S(get_pll_source(),
|
|
plli2sm(STM32_PLLI2S_M_DIVISOR),
|
|
STM32_PLLI2S_N_MULTIPLIER,
|
|
plli2sr(STM32_PLLI2S_R_DIVISOR));
|
|
#endif
|
|
}
|
|
|
|
#endif /* STM32_PLLI2S_ENABLED */
|
|
|
|
/**
|
|
* @brief Activate default clocks
|
|
*/
|
|
void config_enable_default_clocks(void)
|
|
{
|
|
/* Power Interface clock enabled by default */
|
|
LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_PWR);
|
|
}
|