222 lines
6.5 KiB
ReStructuredText
222 lines
6.5 KiB
ReStructuredText
.. _stm32f072b_disco_board:
|
|
|
|
ST STM32F072B-DISCO
|
|
###################
|
|
|
|
Overview
|
|
********
|
|
|
|
The STM32F072B-DISCO Discovery kit features an ARM Cortex-M0 based STM32F072RB
|
|
MCU with everything required for beginners and experienced users to get
|
|
started quickly. Here are some highlights of the STM32F072B-DISCO board:
|
|
|
|
- STM32 microcontroller in LQFP64 package
|
|
- Extension header for LQFP64 I/Os for a quick connection to the prototyping
|
|
board and easy probing
|
|
- On-board ST-LINK/V2, debugger/programmer with SWD connector
|
|
- Board power supply: through USB bus or from an external 5 V supply voltage
|
|
- External application power supply: 3 V and 5 V
|
|
|
|
- Six LEDs:
|
|
|
|
- LD1 (red/green) for USB communication
|
|
- LD2 (red) for 3.3 V power on
|
|
- Four user LEDs: LD3 (orange), LD4 (green), LD5 (red) and LD6 (blue)
|
|
|
|
- Two push-buttons: USER and RESET
|
|
- USB USER with Mini-B connector
|
|
- L3GD20, ST MEMS motion sensor, 3-axis digital output gyroscope
|
|
- One linear touch sensor or four touch keys
|
|
- RF EEprom daughter board connector
|
|
|
|
.. image:: img/en.stm32f072b_disco.jpg
|
|
:width: 272px
|
|
:align: center
|
|
:height: 551px
|
|
:alt: STM32F072B-DISCO
|
|
|
|
More information about the board can be found at the
|
|
`STM32F072B-DISCO website`_.
|
|
|
|
Hardware
|
|
********
|
|
|
|
STM32F072B-DISCO Discovery kit provides the following hardware components:
|
|
|
|
- STM32F072RBTT6 in LQFP64 package
|
|
- ARM |reg| 32-bit Cortex |reg| -M0 CPU
|
|
- 48 MHz max CPU frequency
|
|
- VDD from 2.0 V to 3.6 V
|
|
- 128 KB Flash
|
|
- 16 KB SRAM
|
|
- GPIO with external interrupt capability
|
|
- 12-bit ADC with 39 channels
|
|
- 12-bit D/A converters
|
|
- RTC
|
|
- General Purpose Timers (12)
|
|
- USART/UART (4)
|
|
- I2C (2)
|
|
- SPI (2)
|
|
- CAN
|
|
- USB 2.0 full speed interface
|
|
- DMA Controller
|
|
- 24 capacitive sensing channels for touchkey, linear and rotary touch sensors
|
|
|
|
More information about STM32F072RB can be found here:
|
|
- `STM32F072RB on www.st.com`_
|
|
- `STM32F072xB reference manual`_
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The Zephyr stm32f072b_disco board configuration supports the following hardware
|
|
features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+-------------------------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+-------------------------------------+
|
|
| CLOCK | on-chip | reset and clock control |
|
|
+-----------+------------+-------------------------------------+
|
|
| WATCHDOG | on-chip | independent watchdog |
|
|
+-----------+------------+-------------------------------------+
|
|
| I2C | on-chip | i2c controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| SPI | on-chip | SPI controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| CAN | on-chip | CAN controller |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
.. note:: CAN feature requires CAN transceiver, such as `SK Pang CAN breakout board`_.
|
|
|
|
Other hardware features are not yet supported in this Zephyr port.
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
|
|
``boards/arm/stm32f072b_disco/stm32f072b_disco_defconfig``
|
|
|
|
|
|
Pin Mapping
|
|
===========
|
|
|
|
STM32F072B-DISCO Discovery kit has 6 GPIO controllers. These controllers are
|
|
responsible for pin muxing, input/output, pull-up, etc.
|
|
|
|
For mode details please refer to `STM32F072B-DISCO board User Manual`_.
|
|
|
|
Default Zephyr Peripheral Mapping:
|
|
----------------------------------
|
|
- UART_1_TX : PB6
|
|
- UART_1_RX : PB7
|
|
- I2C1_SCL : PB8
|
|
- I2C1_SDA : PB9
|
|
- I2C2_SCL : PB10
|
|
- I2C2_SDA : PB11
|
|
- SPI1_SCK : PB3
|
|
- SPI1_MISO : PB4
|
|
- SPI1_MOSI : PB5
|
|
- USER_PB : PA0
|
|
- LD3 : PC6
|
|
- LD4 : PC8
|
|
- LD5 : PC9
|
|
- LD6 : PC7
|
|
- CAN_RX : PB8
|
|
- CAN_TX : PB9
|
|
|
|
System Clock
|
|
============
|
|
|
|
STM32F072B-DISCO System Clock could be driven by internal or external
|
|
oscillator, as well as main PLL clock. By default System clock is driven
|
|
by PLL clock at 72 MHz, driven by internal 8 MHz oscillator.
|
|
|
|
Serial Port
|
|
===========
|
|
|
|
STM32F072B-DISCO Discovery kit has up to 4 UARTs. The Zephyr console output
|
|
is assigned to UART 1. Default settings are 115200 8N1.
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Applications for the ``stm32f072b_disco`` board configuration can be built and
|
|
flashed in the usual way (see :ref:`build_an_application` and
|
|
:ref:`application_run` for more details).
|
|
|
|
Flashing
|
|
========
|
|
|
|
STM32F072B-DISCO board includes an ST-LINK/V2 embedded debug tool interface.
|
|
This interface is supported by the openocd version included in the Zephyr SDK.
|
|
|
|
|
|
Flashing an application to STM32F072B-DISCO
|
|
-------------------------------------------
|
|
|
|
First, connect the STM32F072B-DISCO Discovery kit to your host computer using
|
|
the USB port to prepare it for flashing. Then build and flash your application.
|
|
|
|
Here is an example for the :ref:`hello_world` application.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: stm32f072b_disco
|
|
:goals: build flash
|
|
|
|
Run a serial host program to connect with your board. A TTL(3.3V) serial
|
|
adapter is required.
|
|
|
|
.. code-block:: console
|
|
|
|
$ minicom -D /dev/<tty device>
|
|
|
|
Replace <tty_device> with the port where the serial adapter can be found.
|
|
For example, under Linux, /dev/ttyUSB0.
|
|
|
|
You should see the following message on the console:
|
|
|
|
.. code-block:: console
|
|
|
|
Hello World! arm
|
|
|
|
|
|
Debugging
|
|
=========
|
|
|
|
You can debug an application in the usual way. Here is an example for the
|
|
:ref:`hello_world` application.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: stm32f072b_disco
|
|
:goals: debug
|
|
|
|
References
|
|
**********
|
|
|
|
.. target-notes::
|
|
|
|
.. _STM32F072B-DISCO website:
|
|
http://www.st.com/en/evaluation-tools/32f072bdiscovery.html
|
|
|
|
|
|
.. _STM32F072B-DISCO board User Manual:
|
|
http://www.st.com/resource/en/user_manual/dm00099401.pdf
|
|
|
|
.. _STM32F072RB on www.st.com:
|
|
http://www.st.com/en/microcontrollers/stm32f072rb.html
|
|
|
|
.. _STM32F072xB reference manual:
|
|
http://www.st.com/resource/en/reference_manual/dm00031936.pdf
|
|
|
|
.. _SK Pang CAN breakout board:
|
|
http://skpang.co.uk/catalog/canbus-can-fd-breakout-board-5v-p-242.html
|