171 lines
3.4 KiB
Plaintext
171 lines
3.4 KiB
Plaintext
menuconfig BMG160
|
|
bool "Bosch BMG160 gyroscope support"
|
|
depends on SENSOR
|
|
depends on I2C
|
|
default n
|
|
help
|
|
Enable Bosch BMG160 gyroscope support.
|
|
|
|
config BMG160_SYS_LOG_LEVEL
|
|
int "BMG160 Log level"
|
|
depends on SYS_LOG && BMG160
|
|
default 0
|
|
range 0 4
|
|
help
|
|
Sets log level for BMG160 driver.
|
|
Levels are:
|
|
0 OFF, do not write
|
|
1 ERROR, only write SYS_LOG_ERR
|
|
2 WARNING, write SYS_LOG_WRN in adition to previous level
|
|
3 INFO, write SYS_LOG_INF in adition to previous levels
|
|
4 DEBUG, write SYS_LOG_DBG in adition to previous levels
|
|
|
|
config BMG160_INIT_PRIORITY
|
|
int
|
|
prompt "BMG160 Init priority"
|
|
default 70
|
|
depends on BMG160
|
|
help
|
|
Device driver initialization priority.
|
|
As the device is connected to SPI bus, its driver has
|
|
to be initialized after the SPI one.
|
|
|
|
config BMG160_DRV_NAME
|
|
string "Driver's name"
|
|
depends on BMG160
|
|
default "bmg160"
|
|
help
|
|
Name for the BMG160 driver which will be used for binding.
|
|
|
|
config BMG160_I2C_PORT_NAME
|
|
string "I2C master controller port name"
|
|
depends on BMG160
|
|
default "I2C_0"
|
|
help
|
|
Master I2C port name through which BMG160 chip is accessed.
|
|
|
|
config BMG160_I2C_ADDR
|
|
hex "BMG160 I2C address"
|
|
depends on BMG160
|
|
default 0x68
|
|
help
|
|
BMG160 chip's I2C address. Chip supports two addresses: 0x68 and 0x69 (if
|
|
SDO pin is pulled to GND).
|
|
|
|
choice
|
|
prompt "BMG160 I2C bus speed"
|
|
default BMG160_I2C_SPEED_STANDARD
|
|
depends on BMG160
|
|
|
|
config BMG160_I2C_SPEED_STANDARD
|
|
bool "Standard"
|
|
help
|
|
Standard bus speed of up to 100kHz.
|
|
|
|
config BMG160_I2C_SPEED_FAST
|
|
bool "Fast"
|
|
help
|
|
Fast bus speed of up to 400KHz.
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Trigger mode"
|
|
depends on BMG160
|
|
default BMG160_TRIGGER_GLOBAL_FIBER
|
|
help
|
|
Specify the type of triggering to be used by the driver.
|
|
|
|
config BMG160_TRIGGER_NONE
|
|
bool
|
|
prompt "No trigger"
|
|
|
|
config BMG160_TRIGGER_GLOBAL_FIBER
|
|
bool "Use global fiber"
|
|
depends on SYSTEM_WORKQUEUE
|
|
select BMG160_TRIGGER
|
|
|
|
config BMG160_TRIGGER_OWN_FIBER
|
|
bool "Use own fiber"
|
|
select BMG160_TRIGGER
|
|
endchoice
|
|
|
|
config BMG160_TRIGGER
|
|
bool
|
|
depends on BMG160
|
|
|
|
config BMG160_FIBER_PRIORITY
|
|
int "Own fiber priority"
|
|
depends on BMG160 && BMG160_TRIGGER_OWN_FIBER
|
|
default 10
|
|
help
|
|
The priority of the fiber used for handling interrupts.
|
|
|
|
config BMG160_FIBER_STACK_SIZE
|
|
int "Own fiber stack size"
|
|
depends on BMG160 && BMG160_TRIGGER_OWN_FIBER
|
|
default 1024
|
|
help
|
|
The fiber stack size.
|
|
|
|
config BMG160_GPIO_PORT_NAME
|
|
string "GPIO controller port name"
|
|
depends on BMG160 && BMG160_TRIGGER
|
|
default "GPIO_0"
|
|
help
|
|
The gpio controller the interrupt pin is atteched to.
|
|
|
|
config BMG160_INT_PIN
|
|
hex "BMG160 INT PIN"
|
|
depends on BMG160 && BMG160_TRIGGER
|
|
default 2
|
|
help
|
|
BMG160 interrupt pin.
|
|
|
|
choice
|
|
prompt "Gyroscope range setting."
|
|
depends on BMG160
|
|
default BMG160_RANGE_RUNTIME
|
|
|
|
config BMG160_RANGE_RUNTIME
|
|
bool "Set at runtime."
|
|
|
|
config BMG160_RANGE_2000DPS
|
|
bool "2000 DPS"
|
|
|
|
config BMG160_RANGE_1000DPS
|
|
bool "1000 DPS"
|
|
|
|
config BMG160_RANGE_500DPS
|
|
bool "500 DPS"
|
|
|
|
config BMG160_RANGE_250DPS
|
|
bool "250 DPS"
|
|
|
|
config BMG160_RANGE_125DPS
|
|
bool "125 DPS"
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Gyroscope sampling frequency."
|
|
depends on BMG160
|
|
default BMG160_ODR_RUNTIME
|
|
|
|
config BMG160_ODR_RUNTIME
|
|
bool "Set at runtime."
|
|
|
|
config BMG160_ODR_100
|
|
bool "100 Hz"
|
|
|
|
config BMG160_ODR_200
|
|
bool "200 Hz"
|
|
|
|
config BMG160_ODR_400
|
|
bool "400 Hz"
|
|
|
|
config BMG160_ODR_1000
|
|
bool "1000 Hz"
|
|
|
|
config BMG160_ODR_2000
|
|
bool "2000 Hz"
|
|
endchoice
|