94 lines
2.0 KiB
C
94 lines
2.0 KiB
C
/* nrf51-pm.c Power Management for nrf51 chip */
|
|
|
|
/*
|
|
* Copyright (c) 2016 Intel Corporation
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#include <zephyr.h>
|
|
#include <gpio.h>
|
|
#include <uart.h>
|
|
|
|
#define BT_DBG_ENABLED IS_ENABLED(CONFIG_BLUETOOTH_DEBUG_HCI_DRIVER)
|
|
#include <bluetooth/log.h>
|
|
#include <errno.h>
|
|
|
|
#define NBLE_SWDIO_PIN 6
|
|
#define NBLE_RESET_PIN NBLE_SWDIO_PIN
|
|
#define NBLE_BTWAKE_PIN 5
|
|
|
|
static struct device *nrf51_gpio;
|
|
|
|
int nrf51_wakeup(void)
|
|
{
|
|
return gpio_pin_write(nrf51_gpio, NBLE_BTWAKE_PIN, 1);
|
|
}
|
|
|
|
int nrf51_allow_sleep(void)
|
|
{
|
|
return gpio_pin_write(nrf51_gpio, NBLE_BTWAKE_PIN, 0);
|
|
}
|
|
|
|
int nrf51_init(struct device *dev)
|
|
{
|
|
u8_t c;
|
|
int ret;
|
|
|
|
nrf51_gpio = device_get_binding("GPIO_0");
|
|
if (!nrf51_gpio) {
|
|
BT_ERR("Cannot find GPIO_0");
|
|
return -ENODEV;
|
|
}
|
|
|
|
ret = gpio_pin_configure(nrf51_gpio, NBLE_RESET_PIN, GPIO_DIR_OUT);
|
|
if (ret) {
|
|
BT_ERR("Error configuring pin %d", NBLE_RESET_PIN);
|
|
return -ENODEV;
|
|
}
|
|
|
|
/* Reset hold time is 0.2us (normal) or 100us (SWD debug) */
|
|
ret = gpio_pin_write(nrf51_gpio, NBLE_RESET_PIN, 0);
|
|
if (ret) {
|
|
BT_ERR("Error pin write %d", NBLE_RESET_PIN);
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* Drain the fifo */
|
|
while (uart_fifo_read(dev, &c, 1)) {
|
|
continue;
|
|
}
|
|
|
|
/**
|
|
* NBLE reset is achieved by asserting low the SWDIO pin.
|
|
* However, the BLE Core chip can be in SWD debug mode,
|
|
* and NRF_POWER->RESET = 0 due to, other constraints: therefore,
|
|
* this reset might not work everytime, especially after
|
|
* flashing or debugging.
|
|
*/
|
|
|
|
/* sleep 1ms depending on context */
|
|
k_sleep(1);
|
|
|
|
ret = gpio_pin_write(nrf51_gpio, NBLE_RESET_PIN, 1);
|
|
if (ret) {
|
|
BT_ERR("Error pin write %d", NBLE_RESET_PIN);
|
|
return -EINVAL;
|
|
}
|
|
|
|
/* Set back GPIO to input to avoid interfering with external debugger */
|
|
ret = gpio_pin_configure(nrf51_gpio, NBLE_RESET_PIN, GPIO_DIR_IN);
|
|
if (ret) {
|
|
BT_ERR("Error configuring pin %d", NBLE_RESET_PIN);
|
|
return -ENODEV;
|
|
}
|
|
|
|
ret = gpio_pin_configure(nrf51_gpio, NBLE_BTWAKE_PIN, GPIO_DIR_OUT);
|
|
if (ret) {
|
|
BT_ERR("Error configuring pin %d", NBLE_BTWAKE_PIN);
|
|
return -ENODEV;
|
|
}
|
|
|
|
return nrf51_wakeup();
|
|
}
|