95 lines
2.3 KiB
Plaintext
95 lines
2.3 KiB
Plaintext
# Kconfig - Bluetooth drivers configuration options
|
|
|
|
#
|
|
# Copyright (c) 2016 Intel Corporation
|
|
#
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
#
|
|
|
|
comment "Bluetooth HCI Driver Options"
|
|
|
|
config BT_UART
|
|
bool
|
|
|
|
choice BT_HCI_BUS_TYPE
|
|
prompt "Bluetooth HCI driver"
|
|
|
|
config BT_H4
|
|
bool "H:4 UART"
|
|
select UART_INTERRUPT_DRIVEN
|
|
select BT_UART
|
|
select BT_RECV_IS_RX_THREAD
|
|
depends on SERIAL
|
|
help
|
|
Bluetooth H:4 UART driver. Requires hardware flow control
|
|
lines to be available.
|
|
|
|
config BT_H5
|
|
bool "H:5 UART [EXPERIMENTAL]"
|
|
select UART_INTERRUPT_DRIVEN
|
|
select BT_UART
|
|
depends on SERIAL
|
|
help
|
|
Bluetooth three-wire (H:5) UART driver. Implementation of HCI
|
|
Three-Wire UART Transport Layer.
|
|
|
|
config BT_SPI
|
|
bool "SPI HCI"
|
|
depends on SPI
|
|
help
|
|
Supports Bluetooth ICs using SPI as the communication protocol.
|
|
HCI packets are sent and received as single Byte transfers,
|
|
prepended after a known header. Headers may vary per device, so
|
|
additional platform specific knowledge may need to be added as
|
|
devices are.
|
|
|
|
config BT_STM32_IPM
|
|
bool "IPM HCI"
|
|
select USE_STM32_HAL_CORTEX
|
|
select HAS_STLIB
|
|
help
|
|
TODO
|
|
|
|
config BT_USERCHAN
|
|
bool "HCI User Channel based driver"
|
|
depends on BOARD_NATIVE_POSIX
|
|
help
|
|
This driver provides access to the local Linux host's Bluetooth
|
|
adapter using a User Channel HCI socket to the Linux kernel. It
|
|
is only intended to be used with the native POSIX build of Zephyr.
|
|
The Bluetooth adapter must be powered off in order for Zephyr to
|
|
be able to use it.
|
|
|
|
config BT_NO_DRIVER
|
|
bool "No default HCI driver"
|
|
help
|
|
This is intended for unit tests where no internal driver
|
|
should be selected.
|
|
|
|
endchoice
|
|
|
|
config BT_UART_ON_DEV_NAME
|
|
string "Device Name of UART Device for Bluetooth"
|
|
default "$(dt_str_val,DT_BT_UART_ON_DEV_NAME)" if HAS_DTS
|
|
default "UART_0"
|
|
depends on BT_UART
|
|
help
|
|
This option specifies the name of UART device to be used
|
|
for Bluetooth.
|
|
|
|
if BT_SPI
|
|
|
|
config BT_BLUENRG_ACI
|
|
bool "Enable ACI message with with BlueNRG-based devices"
|
|
help
|
|
Enable support for devices compatible with the BlueNRG Bluetooth
|
|
Stack. Current driver supports: ST BLUENRG-MS.
|
|
|
|
config BT_SPI_BLUENRG
|
|
bool "Enable compatibility with BlueNRG-based devices"
|
|
help
|
|
Enable support for devices compatible with the BlueNRG Bluetooth
|
|
Stack. Current driver supports: ST BLUENRG-MS.
|
|
|
|
endif # BT_SPI
|