98 lines
1.9 KiB
Plaintext
98 lines
1.9 KiB
Plaintext
/*
|
|
* Copyright (c) 2019 STMicroelectronics
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/mp1/stm32mp157.dtsi>
|
|
#include <st/mp1/stm32mp157cacx-pinctrl.dtsi>
|
|
#include "arduino_r3_connector.dtsi"
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32MP157-DK2 board";
|
|
compatible = "st,stm32mp157c-dk2";
|
|
chosen {
|
|
/*
|
|
* By default, Zephyr console and shell are assigned to
|
|
* remoteproc. To enable console and shell over UART, uncomment
|
|
* following lines and set the correct config in
|
|
* stm32mp157c_dk2_defconfig "Serial Port" section in Zephyr
|
|
* board documentation.
|
|
* zephyr,console = &usart3;
|
|
* zephyr,shell-uart = &usart3;
|
|
*/
|
|
zephyr,flash = &retram;
|
|
zephyr,sram = &mcusram;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
red_led_1: led_1 {
|
|
gpios = <&gpioh 7 GPIO_ACTIVE_HIGH>;
|
|
label = "LD7";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button {
|
|
label = "User 1";
|
|
gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &red_led_1;
|
|
sw0 = &user_button;
|
|
};
|
|
|
|
};
|
|
|
|
&rcc {
|
|
clock-frequency = <DT_FREQ_M(209)>;
|
|
};
|
|
|
|
&spi4_miso_pe13{ slew-rate = "very-high-speed"; };
|
|
|
|
&spi4{
|
|
pinctrl-0 = <&spi4_nss_pe11 &spi4_sck_pe12
|
|
&spi4_miso_pe13 &spi4_mosi_pe14>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&spi5_miso_pf8{ slew-rate = "very-high-speed"; };
|
|
|
|
&spi5{
|
|
pinctrl-0 = <&spi5_nss_pf6 &spi5_sck_pf7
|
|
&spi5_miso_pf8 &spi5_mosi_pf9>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&usart3 {
|
|
pinctrl-0 = <&usart3_tx_pb10 &usart3_rx_pb12>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart7 {
|
|
pinctrl-0 = <&uart7_tx_pe8 &uart7_rx_pe7>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&mailbox {
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c5 {
|
|
pinctrl-0 = <&i2c5_scl_pa11 &i2c5_sda_pa12>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|