166 lines
6.8 KiB
ReStructuredText
166 lines
6.8 KiB
ReStructuredText
.. _beagleconnect_freedom:
|
|
|
|
BeagleConnect Freedom
|
|
#####################
|
|
|
|
Overview
|
|
********
|
|
|
|
BeagleBoard.org BeagleConnect Freedom is a wireless
|
|
Internet of Things board based on the SimpleLink multi-Standard CC1352P7 wireless MCU.
|
|
|
|
|
|
.. figure:: img/beagleconnect_freedom.webp
|
|
:align: center
|
|
:width: 500px
|
|
:alt: BeagleBoard.org BeagleConnect Freedom
|
|
|
|
BeagleBoard.org BeagleConnect Freedom
|
|
|
|
Hardware
|
|
********
|
|
BeagleBoard.org BeagleConnect Freedom board features the TI CC1352P7 wireless microcontroller.
|
|
The BeagleConnect Freedom is the first available BeagleConnect solution consisting
|
|
of a board and a case which ships programmed and ready to be used.
|
|
|
|
BeagleConnect Freedom board runs the Zephyr RTOS and has mikroBUS ports along
|
|
with BLE and Sub-GHz radios on it.
|
|
|
|
The CC1352P7 wireless MCU has a 48 MHz Arm Cortex-M4F SoC and a Bluetooth Low Energy and IEEE 802.15.4.
|
|
|
|
The board also features a TI MSP430F5503 microcontroller used as a USB-to-serial bridge and
|
|
GPIO expander.
|
|
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The board configuration supports the following hardware features:
|
|
|
|
+-----------+------------+----------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+======================+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+----------------------+
|
|
| MPU | on-chip | arch/arm |
|
|
+-----------+------------+----------------------+
|
|
| NVIC | on-chip | arch/arm |
|
|
+-----------+------------+----------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+----------------------+
|
|
| UART | on-chip | serial |
|
|
+-----------+------------+----------------------+
|
|
| I2C | on-chip | i2c |
|
|
+-----------+------------+----------------------+
|
|
| SPI | on-chip | spi |
|
|
+-----------+------------+----------------------+
|
|
| HWINFO | on-chip | hwinfo |
|
|
+-----------+------------+----------------------+
|
|
| I2C | off-chip | OPT3001 |
|
|
+-----------+------------+----------------------+
|
|
| I2C | off-chip | HDC2010 |
|
|
+-----------+------------+----------------------+
|
|
| I2C | off-chip | BCF_BRIDGE_MCU |
|
|
+-----------+------------+----------------------+
|
|
| ADC | on-chip | adc |
|
|
+-----------+------------+----------------------+
|
|
| PWM | on-chip | pwm |
|
|
+-----------+------------+----------------------+
|
|
| FLASH | on-chip | flash |
|
|
+-----------+------------+----------------------+
|
|
| RADIO | on-chip | ieee802154 |
|
|
+-----------+------------+----------------------+
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
.. figure:: img/beagleconnect_freedom_front_annotated.webp
|
|
:align: center
|
|
:width: 500px
|
|
:alt: Front connections
|
|
|
|
BeagleConnect Freedom front connections
|
|
|
|
.. figure:: img/beagleconnect_freedom_back_annotated.webp
|
|
:align: center
|
|
:width: 500px
|
|
:alt: Back connections
|
|
|
|
BeagleConnect Freedom back connections
|
|
|
|
|
|
+-------+--------------+-------------------------------------+
|
|
| Pin | Function | Usage |
|
|
+=======+==============+=====================================+
|
|
| DIO5 | RST_MB2 | Reset mikroBUS port 2 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO6 | RST_MB1 | Reset mikroBUS port 1 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO7 | INT_SENSOR | On-board sensor interrupts |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO8 | FLASH_CS | SPI flash chip-select |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO9 | SDO / PICO | SPI serial data output |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO10 | SCK | SPI serial clock |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO11 | SDI / POCI | SPI serial data input |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO12 | CC1352_RX | UART RXD mikroBUS port 1 or MSP430 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO13 | CC1352_TX | UART TXD mikroBUS port 1 or MSP430 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO14 | I2C_CTRL | Enable on-board sensor I2C bus |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO15 | USER_BOOT | BOOT button status |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO16 | INT_MB1 | INTERRUPT PIN on mikroBUS port 1 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO17 | PWM_MB1 | PWM PIN on mikroBUS port 1 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO18 | LED_LINK | Radio link indicator LED |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO19 | PWM_MB2 | PWM PIN on mikroBUS port 2 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO20 | INT_MB2 | INTERRUPT PIN on mikroBUS port 2 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO21 | MB2_RX | UART RXD on mikroBUS port 2 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO22 | MB2_TX | UART TXD on mikroBUS port 2 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO23 | AN_MB1 | ANALOG PIN on mikroBUS port 1 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO24 | AN_MB2 | ANALOG PIN on mikroBUS port 2 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO25 | SCL | I2C SCL |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO26 | SDA | I2C SDA |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO27 | CS_MB2 | SPI CS on microBUS port 2 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO28 | CS_MB1 | SPI CS on microBUS port 1 |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO29 | REF_SW_CTRL1 | Antenna mux PA enable |
|
|
+-------+--------------+-------------------------------------+
|
|
| DIO30 | REF_SW_CTRL2 | Antenna mux SubG enable |
|
|
+-------+--------------+-------------------------------------+
|
|
|
|
System requirements
|
|
===================
|
|
|
|
Prerequisites
|
|
-------------
|
|
|
|
BeagleConnect Freedom requires `CC1352 Flasher <https://pypi.org/project/cc1352-flasher/>`_ for
|
|
flashing Zephyr firmware using ``west flash``.
|
|
|
|
.. code-block:: console
|
|
|
|
pip3 install cc1352-flasher
|
|
|
|
References
|
|
**********
|
|
|
|
BeagleBoard.org BeagleConnect Freedom reference:
|
|
https://beagleconnect.org
|