OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/serial/uart_ns16550.c

852 lines
22 KiB
C
Raw Blame History

/* ns16550.c - NS16550D serial driver */
/*
* Copyright (c) 2010, 2012-2015 Wind River Systems, Inc.
*
* SPDX-License-Identifier: Apache-2.0
*/
/**
* @brief NS16550 Serial Driver
*
* This is the driver for the Intel NS16550 UART Chip used on the PC 386.
* It uses the SCCs in asynchronous mode only.
*
* Before individual UART port can be used, uart_ns16550_port_init() has to be
* called to setup the port.
*
* - the following macro for the number of bytes between register addresses:
*
* UART_REG_ADDR_INTERVAL
*/
#include <errno.h>
#include <kernel.h>
#include <arch/cpu.h>
#include <zephyr/types.h>
#include <board.h>
#include <init.h>
#include <toolchain.h>
#include <linker/sections.h>
#include <uart.h>
#include <sys_io.h>
#ifdef CONFIG_PCI
#include <pci/pci.h>
#include <pci/pci_mgr.h>
#endif /* CONFIG_PCI */
#include "uart_ns16550.h"
/* register definitions */
#define REG_THR 0x00 /* Transmitter holding reg. */
#define REG_RDR 0x00 /* Receiver data reg. */
#define REG_BRDL 0x00 /* Baud rate divisor (LSB) */
#define REG_BRDH 0x01 /* Baud rate divisor (MSB) */
#define REG_IER 0x01 /* Interrupt enable reg. */
#define REG_IIR 0x02 /* Interrupt ID reg. */
#define REG_FCR 0x02 /* FIFO control reg. */
#define REG_LCR 0x03 /* Line control reg. */
#define REG_MDC 0x04 /* Modem control reg. */
#define REG_LSR 0x05 /* Line status reg. */
#define REG_MSR 0x06 /* Modem status reg. */
#define REG_DLF 0xC0 /* Divisor Latch Fraction */
/* equates for interrupt enable register */
#define IER_RXRDY 0x01 /* receiver data ready */
#define IER_TBE 0x02 /* transmit bit enable */
#define IER_LSR 0x04 /* line status interrupts */
#define IER_MSI 0x08 /* modem status interrupts */
/* equates for interrupt identification register */
#define IIR_MSTAT 0x00 /* modem status interrupt */
#define IIR_NIP 0x01 /* no interrupt pending */
#define IIR_THRE 0x02 /* transmit holding register empty interrupt */
#define IIR_RBRF 0x04 /* receiver buffer register full interrupt */
#define IIR_LS 0x06 /* receiver line status interrupt */
#define IIR_MASK 0x07 /* interrupt id bits mask */
#define IIR_ID 0x06 /* interrupt ID mask without NIP */
/* equates for FIFO control register */
#define FCR_FIFO 0x01 /* enable XMIT and RCVR FIFO */
#define FCR_RCVRCLR 0x02 /* clear RCVR FIFO */
#define FCR_XMITCLR 0x04 /* clear XMIT FIFO */
/*
* Per PC16550D (Literature Number: SNLS378B):
*
* RXRDY, Mode 0: When in the 16450 Mode (FCR0 = 0) or in
* the FIFO Mode (FCR0 = 1, FCR3 = 0) and there is at least 1
* character in the RCVR FIFO or RCVR holding register, the
* RXRDY pin (29) will be low active. Once it is activated the
* RXRDY pin will go inactive when there are no more charac-
* ters in the FIFO or holding register.
*
* RXRDY, Mode 1: In the FIFO Mode (FCR0 = 1) when the
* FCR3 = 1 and the trigger level or the timeout has been
* reached, the RXRDY pin will go low active. Once it is acti-
* vated it will go inactive when there are no more characters
* in the FIFO or holding register.
*
* TXRDY, Mode 0: In the 16450 Mode (FCR0 = 0) or in the
* FIFO Mode (FCR0 = 1, FCR3 = 0) and there are no charac-
* ters in the XMIT FIFO or XMIT holding register, the TXRDY
* pin (24) will be low active. Once it is activated the TXRDY
* pin will go inactive after the first character is loaded into the
* XMIT FIFO or holding register.
*
* TXRDY, Mode 1: In the FIFO Mode (FCR0 = 1) when
* FCR3 = 1 and there are no characters in the XMIT FIFO, the
* TXRDY pin will go low active. This pin will become inactive
* when the XMIT FIFO is completely full.
*/
#define FCR_MODE0 0x00 /* set receiver in mode 0 */
#define FCR_MODE1 0x08 /* set receiver in mode 1 */
/* RCVR FIFO interrupt levels: trigger interrupt with this bytes in FIFO */
#define FCR_FIFO_1 0x00 /* 1 byte in RCVR FIFO */
#define FCR_FIFO_4 0x40 /* 4 bytes in RCVR FIFO */
#define FCR_FIFO_8 0x80 /* 8 bytes in RCVR FIFO */
#define FCR_FIFO_14 0xC0 /* 14 bytes in RCVR FIFO */
/*
* UART NS16750 supports 64 bytes FIFO, which can be enabled
* via the FCR register
*/
#define FCR_FIFO_64 0x20 /* Enable 64 bytes FIFO */
/* constants for line control register */
#define LCR_CS5 0x00 /* 5 bits data size */
#define LCR_CS6 0x01 /* 6 bits data size */
#define LCR_CS7 0x02 /* 7 bits data size */
#define LCR_CS8 0x03 /* 8 bits data size */
#define LCR_2_STB 0x04 /* 2 stop bits */
#define LCR_1_STB 0x00 /* 1 stop bit */
#define LCR_PEN 0x08 /* parity enable */
#define LCR_PDIS 0x00 /* parity disable */
#define LCR_EPS 0x10 /* even parity select */
#define LCR_SP 0x20 /* stick parity select */
#define LCR_SBRK 0x40 /* break control bit */
#define LCR_DLAB 0x80 /* divisor latch access enable */
/* constants for the modem control register */
#define MCR_DTR 0x01 /* dtr output */
#define MCR_RTS 0x02 /* rts output */
#define MCR_OUT1 0x04 /* output #1 */
#define MCR_OUT2 0x08 /* output #2 */
#define MCR_LOOP 0x10 /* loop back */
#define MCR_AFCE 0x20 /* auto flow control enable */
/* constants for line status register */
#define LSR_RXRDY 0x01 /* receiver data available */
#define LSR_OE 0x02 /* overrun error */
#define LSR_PE 0x04 /* parity error */
#define LSR_FE 0x08 /* framing error */
#define LSR_BI 0x10 /* break interrupt */
#define LSR_EOB_MASK 0x1E /* Error or Break mask */
#define LSR_THRE 0x20 /* transmit holding register empty */
#define LSR_TEMT 0x40 /* transmitter empty */
/* constants for modem status register */
#define MSR_DCTS 0x01 /* cts change */
#define MSR_DDSR 0x02 /* dsr change */
#define MSR_DRI 0x04 /* ring change */
#define MSR_DDCD 0x08 /* data carrier change */
#define MSR_CTS 0x10 /* complement of cts */
#define MSR_DSR 0x20 /* complement of dsr */
#define MSR_RI 0x40 /* complement of ring signal */
#define MSR_DCD 0x80 /* complement of dcd */
/* convenience defines */
#define DEV_CFG(dev) \
((const struct uart_ns16550_device_config * const) \
(dev)->config->config_info)
#define DEV_DATA(dev) \
((struct uart_ns16550_dev_data_t *)(dev)->driver_data)
#define THR(dev) (DEV_DATA(dev)->port + REG_THR * UART_REG_ADDR_INTERVAL)
#define RDR(dev) (DEV_DATA(dev)->port + REG_RDR * UART_REG_ADDR_INTERVAL)
#define BRDL(dev) (DEV_DATA(dev)->port + REG_BRDL * UART_REG_ADDR_INTERVAL)
#define BRDH(dev) (DEV_DATA(dev)->port + REG_BRDH * UART_REG_ADDR_INTERVAL)
#define IER(dev) (DEV_DATA(dev)->port + REG_IER * UART_REG_ADDR_INTERVAL)
#define IIR(dev) (DEV_DATA(dev)->port + REG_IIR * UART_REG_ADDR_INTERVAL)
#define FCR(dev) (DEV_DATA(dev)->port + REG_FCR * UART_REG_ADDR_INTERVAL)
#define LCR(dev) (DEV_DATA(dev)->port + REG_LCR * UART_REG_ADDR_INTERVAL)
#define MDC(dev) (DEV_DATA(dev)->port + REG_MDC * UART_REG_ADDR_INTERVAL)
#define LSR(dev) (DEV_DATA(dev)->port + REG_LSR * UART_REG_ADDR_INTERVAL)
#define MSR(dev) (DEV_DATA(dev)->port + REG_MSR * UART_REG_ADDR_INTERVAL)
#define DLF(dev) (DEV_DATA(dev)->port + REG_DLF)
#define IIRC(dev) (DEV_DATA(dev)->iir_cache)
#ifdef UART_NS16550_ACCESS_IOPORT
#define INBYTE(x) sys_in8(x)
#define OUTBYTE(x, d) sys_out8(d, x)
#define UART_REG_ADDR_INTERVAL 1 /* address diff of adjacent regs. */
#else
#define INBYTE(x) sys_read8(x)
#define OUTBYTE(x, d) sys_write8(d, x)
#define UART_REG_ADDR_INTERVAL 4 /* address diff of adjacent regs. */
#endif /* UART_NS16550_ACCESS_IOPORT */
struct uart_ns16550_device_config {
u32_t sys_clk_freq;
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
uart_irq_config_func_t irq_config_func;
#endif
};
/** Device data structure */
struct uart_ns16550_dev_data_t {
u32_t port;
u32_t baud_rate; /**< Baud rate */
u8_t options; /**< Serial port options */
#ifdef CONFIG_PCI
struct pci_dev_info pci_dev;
#endif /* CONFIG_PCI */
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
u8_t iir_cache; /**< cache of IIR since it clears when read */
uart_irq_callback_t cb; /**< Callback function pointer */
#endif
#ifdef CONFIG_UART_NS16550_DLF
u8_t dlf; /**< DLF value */
#endif
};
static const struct uart_driver_api uart_ns16550_driver_api;
#ifdef CONFIG_UART_NS16550_DLF
static inline void set_dlf(struct device *dev, u32_t val)
{
struct uart_ns16550_dev_data_t * const dev_data = DEV_DATA(dev);
OUTBYTE(DLF(dev), val);
dev_data->dlf = val;
}
#endif
static void set_baud_rate(struct device *dev, u32_t baud_rate)
{
const struct uart_ns16550_device_config * const dev_cfg = DEV_CFG(dev);
struct uart_ns16550_dev_data_t * const dev_data = DEV_DATA(dev);
u32_t divisor; /* baud rate divisor */
u8_t lcr_cache;
if ((baud_rate != 0) && (dev_cfg->sys_clk_freq != 0)) {
/* calculate baud rate divisor */
divisor = (dev_cfg->sys_clk_freq / baud_rate) >> 4;
/* set the DLAB to access the baud rate divisor registers */
lcr_cache = INBYTE(LCR(dev));
OUTBYTE(LCR(dev), LCR_DLAB | lcr_cache);
OUTBYTE(BRDL(dev), (unsigned char)(divisor & 0xff));
OUTBYTE(BRDH(dev), (unsigned char)((divisor >> 8) & 0xff));
/* restore the DLAB to access the baud rate divisor registers */
OUTBYTE(LCR(dev), lcr_cache);
dev_data->baud_rate = baud_rate;
}
}
#if defined(CONFIG_UART_NS16550_PCI)
static inline int ns16550_pci_uart_scan(struct device *dev)
{
struct uart_ns16550_dev_data_t * const dev_data = DEV_DATA(dev);
if (dev_data->pci_dev.vendor_id == 0x0000) {
return -EINVAL;
}
pci_bus_scan_init();
if (!pci_bus_scan(&dev_data->pci_dev)) {
return 0;
}
#ifdef CONFIG_PCI_ENUMERATION
dev_data->port = dev_data->pci_dev.addr;
#endif
pci_enable_regs(&dev_data->pci_dev);
return 1;
}
#else
#define ns16550_pci_uart_scan(_unused_) (1)
#endif /* CONFIG_UART_NS16550_PCI */
/**
* @brief Initialize individual UART port
*
* This routine is called to reset the chip in a quiescent state.
*
* @param dev UART device struct
*
* @return 0 if successful, failed otherwise
*/
static int uart_ns16550_init(struct device *dev)
{
struct uart_ns16550_dev_data_t * const dev_data = DEV_DATA(dev);
int old_level; /* old interrupt lock level */
u8_t mdc = 0;
if (!ns16550_pci_uart_scan(dev)) {
dev->driver_api = NULL;
return -ENOTSUP;
}
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
dev_data->iir_cache = 0;
#endif
old_level = irq_lock();
set_baud_rate(dev, dev_data->baud_rate);
#ifdef CONFIG_UART_NS16550_DLF
set_dlf(dev, dev_data->dlf);
#endif
/* 8 data bits, 1 stop bit, no parity, clear DLAB */
OUTBYTE(LCR(dev), LCR_CS8 | LCR_1_STB | LCR_PDIS);
mdc = MCR_OUT2 | MCR_RTS | MCR_DTR;
if ((dev_data->options & UART_OPTION_AFCE) == UART_OPTION_AFCE)
mdc |= MCR_AFCE;
OUTBYTE(MDC(dev), mdc);
/*
* Program FIFO: enabled, mode 0 (set for compatibility with quark),
* generate the interrupt at 8th byte
* Clear TX and RX FIFO
*/
OUTBYTE(FCR(dev),
FCR_FIFO | FCR_MODE0 | FCR_FIFO_8 | FCR_RCVRCLR | FCR_XMITCLR
#ifdef CONFIG_UART_NS16750
| FCR_FIFO_64
#endif
);
/* clear the port */
INBYTE(RDR(dev));
/* disable interrupts */
OUTBYTE(IER(dev), 0x00);
irq_unlock(old_level);
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
DEV_CFG(dev)->irq_config_func(dev);
#endif
return 0;
}
/**
* @brief Poll the device for input.
*
* @param dev UART device struct
* @param c Pointer to character
*
* @return 0 if a character arrived, -1 if the input buffer if empty.
*/
static int uart_ns16550_poll_in(struct device *dev, unsigned char *c)
{
if ((INBYTE(LSR(dev)) & LSR_RXRDY) == 0x00)
return (-1);
/* got a character */
*c = INBYTE(RDR(dev));
return 0;
}
/**
* @brief Output a character in polled mode.
*
* Checks if the transmitter is empty. If empty, a character is written to
* the data register.
*
* If the hardware flow control is enabled then the handshake signal CTS has to
* be asserted in order to send a character.
*
* @param dev UART device struct
* @param c Character to send
*
* @return Sent character
*/
static unsigned char uart_ns16550_poll_out(struct device *dev,
unsigned char c)
{
/* wait for transmitter to ready to accept a character */
while ((INBYTE(LSR(dev)) & LSR_THRE) == 0)
;
OUTBYTE(THR(dev), c);
return c;
}
/**
* @brief Check if an error was received
*
* @param dev UART device struct
*
* @return one of UART_ERROR_OVERRUN, UART_ERROR_PARITY, UART_ERROR_FRAMING,
* UART_ERROR_BREAK if an error was detected, 0 otherwise.
*/
static int uart_ns16550_err_check(struct device *dev)
{
return (INBYTE(LSR(dev)) & LSR_EOB_MASK) >> 1;
}
#if CONFIG_UART_INTERRUPT_DRIVEN
/**
* @brief Fill FIFO with data
*
* @param dev UART device struct
* @param tx_data Data to transmit
* @param size Number of bytes to send
*
* @return Number of bytes sent
*/
static int uart_ns16550_fifo_fill(struct device *dev, const u8_t *tx_data,
int size)
{
int i;
for (i = 0; i < size && (INBYTE(LSR(dev)) & LSR_THRE) != 0; i++) {
OUTBYTE(THR(dev), tx_data[i]);
}
return i;
}
/**
* @brief Read data from FIFO
*
* @param dev UART device struct
* @param rxData Data container
* @param size Container size
*
* @return Number of bytes read
*/
static int uart_ns16550_fifo_read(struct device *dev, u8_t *rx_data,
const int size)
{
int i;
for (i = 0; i < size && (INBYTE(LSR(dev)) & LSR_RXRDY) != 0; i++) {
rx_data[i] = INBYTE(RDR(dev));
}
return i;
}
/**
* @brief Enable TX interrupt in IER
*
* @param dev UART device struct
*
* @return N/A
*/
static void uart_ns16550_irq_tx_enable(struct device *dev)
{
OUTBYTE(IER(dev), INBYTE(IER(dev)) | IER_TBE);
}
/**
* @brief Disable TX interrupt in IER
*
* @param dev UART device struct
*
* @return N/A
*/
static void uart_ns16550_irq_tx_disable(struct device *dev)
{
OUTBYTE(IER(dev), INBYTE(IER(dev)) & (~IER_TBE));
}
/**
* @brief Check if Tx IRQ has been raised
*
* @param dev UART device struct
*
* @return 1 if an IRQ is ready, 0 otherwise
*/
static int uart_ns16550_irq_tx_ready(struct device *dev)
{
return ((IIRC(dev) & IIR_ID) == IIR_THRE);
}
/**
* @brief Check if nothing remains to be transmitted
*
* @param dev UART device struct
*
* @return 1 if nothing remains to be transmitted, 0 otherwise
*/
static int uart_ns16550_irq_tx_complete(struct device *dev)
{
return (INBYTE(LSR(dev)) & (LSR_TEMT | LSR_THRE)) == (LSR_TEMT | LSR_THRE);
}
/**
* @brief Enable RX interrupt in IER
*
* @param dev UART device struct
*
* @return N/A
*/
static void uart_ns16550_irq_rx_enable(struct device *dev)
{
OUTBYTE(IER(dev), INBYTE(IER(dev)) | IER_RXRDY);
}
/**
* @brief Disable RX interrupt in IER
*
* @param dev UART device struct
*
* @return N/A
*/
static void uart_ns16550_irq_rx_disable(struct device *dev)
{
OUTBYTE(IER(dev), INBYTE(IER(dev)) & (~IER_RXRDY));
}
/**
* @brief Check if Rx IRQ has been raised
*
* @param dev UART device struct
*
* @return 1 if an IRQ is ready, 0 otherwise
*/
static int uart_ns16550_irq_rx_ready(struct device *dev)
{
return ((IIRC(dev) & IIR_ID) == IIR_RBRF);
}
/**
* @brief Enable error interrupt in IER
*
* @param dev UART device struct
*
* @return N/A
*/
static void uart_ns16550_irq_err_enable(struct device *dev)
{
OUTBYTE(IER(dev), INBYTE(IER(dev)) | IER_LSR);
}
/**
* @brief Disable error interrupt in IER
*
* @param dev UART device struct
*
* @return 1 if an IRQ is ready, 0 otherwise
*/
static void uart_ns16550_irq_err_disable(struct device *dev)
{
OUTBYTE(IER(dev), INBYTE(IER(dev)) & (~IER_LSR));
}
/**
* @brief Check if any IRQ is pending
*
* @param dev UART device struct
*
* @return 1 if an IRQ is pending, 0 otherwise
*/
static int uart_ns16550_irq_is_pending(struct device *dev)
{
return (!(IIRC(dev) & IIR_NIP));
}
/**
* @brief Update cached contents of IIR
*
* @param dev UART device struct
*
* @return Always 1
*/
static int uart_ns16550_irq_update(struct device *dev)
{
IIRC(dev) = INBYTE(IIR(dev));
return 1;
}
/**
* @brief Set the callback function pointer for IRQ.
*
* @param dev UART device struct
* @param cb Callback function pointer.
*
* @return N/A
*/
static void uart_ns16550_irq_callback_set(struct device *dev,
uart_irq_callback_t cb)
{
struct uart_ns16550_dev_data_t * const dev_data = DEV_DATA(dev);
dev_data->cb = cb;
}
/**
* @brief Interrupt service routine.
*
* This simply calls the callback function, if one exists.
*
* @param arg Argument to ISR.
*
* @return N/A
*/
static void uart_ns16550_isr(void *arg)
{
struct device *dev = arg;
struct uart_ns16550_dev_data_t * const dev_data = DEV_DATA(dev);
if (dev_data->cb) {
dev_data->cb(dev);
}
}
#endif /* CONFIG_UART_INTERRUPT_DRIVEN */
#ifdef CONFIG_UART_NS16550_LINE_CTRL
/**
* @brief Manipulate line control for UART.
*
* @param dev UART device struct
* @param ctrl The line control to be manipulated
* @param val Value to set the line control
*
* @return 0 if successful, failed otherwise
*/
static int uart_ns16550_line_ctrl_set(struct device *dev,
u32_t ctrl, u32_t val)
{
u32_t mdc, chg;
switch (ctrl) {
case LINE_CTRL_BAUD_RATE:
set_baud_rate(dev, val);
return 0;
case LINE_CTRL_RTS:
case LINE_CTRL_DTR:
mdc = INBYTE(MDC(dev));
if (ctrl == LINE_CTRL_RTS) {
chg = MCR_RTS;
} else {
chg = MCR_DTR;
}
if (val) {
mdc |= chg;
} else {
mdc &= ~(chg);
}
OUTBYTE(MDC(dev), mdc);
return 0;
}
return -ENOTSUP;
}
#endif /* CONFIG_UART_NS16550_LINE_CTRL */
#ifdef CONFIG_UART_NS16550_DRV_CMD
/**
* @brief Send extra command to driver
*
* @param dev UART device struct
* @param cmd Command to driver
* @param p Parameter to the command
*
* @return 0 if successful, failed otherwise
*/
static int uart_ns16550_drv_cmd(struct device *dev, u32_t cmd, u32_t p)
{
switch (cmd) {
#ifdef CONFIG_UART_NS16550_DLF
case CMD_SET_DLF:
set_dlf(dev, p);
return 0;
#endif
}
return -ENOTSUP;
}
#endif /* CONFIG_UART_NS16550_DRV_CMD */
static const struct uart_driver_api uart_ns16550_driver_api = {
.poll_in = uart_ns16550_poll_in,
.poll_out = uart_ns16550_poll_out,
.err_check = uart_ns16550_err_check,
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
.fifo_fill = uart_ns16550_fifo_fill,
.fifo_read = uart_ns16550_fifo_read,
.irq_tx_enable = uart_ns16550_irq_tx_enable,
.irq_tx_disable = uart_ns16550_irq_tx_disable,
.irq_tx_ready = uart_ns16550_irq_tx_ready,
.irq_tx_complete = uart_ns16550_irq_tx_complete,
.irq_rx_enable = uart_ns16550_irq_rx_enable,
.irq_rx_disable = uart_ns16550_irq_rx_disable,
.irq_rx_ready = uart_ns16550_irq_rx_ready,
.irq_err_enable = uart_ns16550_irq_err_enable,
.irq_err_disable = uart_ns16550_irq_err_disable,
.irq_is_pending = uart_ns16550_irq_is_pending,
.irq_update = uart_ns16550_irq_update,
.irq_callback_set = uart_ns16550_irq_callback_set,
#endif
#ifdef CONFIG_UART_NS16550_LINE_CTRL
.line_ctrl_set = uart_ns16550_line_ctrl_set,
#endif
#ifdef CONFIG_UART_NS16550_DRV_CMD
.drv_cmd = uart_ns16550_drv_cmd,
#endif
};
#ifdef CONFIG_UART_NS16550_PORT_0
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
static void irq_config_func_0(struct device *port);
#endif
static const struct uart_ns16550_device_config uart_ns16550_dev_cfg_0 = {
.sys_clk_freq = UART_NS16550_PORT_0_CLK_FREQ,
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
.irq_config_func = irq_config_func_0,
#endif
};
static struct uart_ns16550_dev_data_t uart_ns16550_dev_data_0 = {
#ifdef CONFIG_UART_NS16550_PORT_0_PCI
.pci_dev.class_type = UART_NS16550_PORT_0_PCI_CLASS,
.pci_dev.bus = UART_NS16550_PORT_0_PCI_BUS,
.pci_dev.dev = UART_NS16550_PORT_0_PCI_DEV,
.pci_dev.vendor_id = UART_NS16550_PORT_0_PCI_VENDOR_ID,
.pci_dev.device_id = UART_NS16550_PORT_0_PCI_DEVICE_ID,
.pci_dev.function = UART_NS16550_PORT_0_PCI_FUNC,
.pci_dev.bar = UART_NS16550_PORT_0_PCI_BAR,
#endif /* CONFIG_UART_NS16550_PORT_0_PCI */
.port = UART_NS16550_PORT_0_BASE_ADDR,
.baud_rate = CONFIG_UART_NS16550_PORT_0_BAUD_RATE,
.options = CONFIG_UART_NS16550_PORT_0_OPTIONS,
#ifdef CONFIG_UART_NS16550_PORT_0_DLF
.dlf = CONFIG_UART_NS16550_PORT_0_DLF,
#endif
};
DEVICE_AND_API_INIT(uart_ns16550_0, CONFIG_UART_NS16550_PORT_0_NAME, &uart_ns16550_init,
&uart_ns16550_dev_data_0, &uart_ns16550_dev_cfg_0,
PRE_KERNEL_1, CONFIG_KERNEL_INIT_PRIORITY_DEVICE,
&uart_ns16550_driver_api);
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
static void irq_config_func_0(struct device *dev)
{
ARG_UNUSED(dev);
IRQ_CONNECT(UART_NS16550_PORT_0_IRQ,
CONFIG_UART_NS16550_PORT_0_IRQ_PRI,
uart_ns16550_isr, DEVICE_GET(uart_ns16550_0),
UART_IRQ_FLAGS);
irq_enable(UART_NS16550_PORT_0_IRQ);
}
#endif
#endif /* CONFIG_UART_NS16550_PORT_0 */
#ifdef CONFIG_UART_NS16550_PORT_1
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
static void irq_config_func_1(struct device *port);
#endif
static const struct uart_ns16550_device_config uart_ns16550_dev_cfg_1 = {
.sys_clk_freq = UART_NS16550_PORT_1_CLK_FREQ,
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
.irq_config_func = irq_config_func_1,
#endif
};
static struct uart_ns16550_dev_data_t uart_ns16550_dev_data_1 = {
#ifdef CONFIG_UART_NS16550_PORT_1_PCI
.pci_dev.class_type = UART_NS16550_PORT_1_PCI_CLASS,
.pci_dev.bus = UART_NS16550_PORT_1_PCI_BUS,
.pci_dev.dev = UART_NS16550_PORT_1_PCI_DEV,
.pci_dev.vendor_id = UART_NS16550_PORT_1_PCI_VENDOR_ID,
.pci_dev.device_id = UART_NS16550_PORT_1_PCI_DEVICE_ID,
.pci_dev.function = UART_NS16550_PORT_1_PCI_FUNC,
.pci_dev.bar = UART_NS16550_PORT_1_PCI_BAR,
#endif /* CONFIG_UART_NS16550_PORT_1_PCI */
.port = UART_NS16550_PORT_1_BASE_ADDR,
.baud_rate = CONFIG_UART_NS16550_PORT_1_BAUD_RATE,
.options = CONFIG_UART_NS16550_PORT_1_OPTIONS,
#ifdef CONFIG_UART_NS16550_PORT_1_DLF
.dlf = CONFIG_UART_NS16550_PORT_1_DLF,
#endif
};
DEVICE_AND_API_INIT(uart_ns16550_1, CONFIG_UART_NS16550_PORT_1_NAME, &uart_ns16550_init,
&uart_ns16550_dev_data_1, &uart_ns16550_dev_cfg_1,
PRE_KERNEL_1, CONFIG_KERNEL_INIT_PRIORITY_DEVICE,
&uart_ns16550_driver_api);
#ifdef CONFIG_UART_INTERRUPT_DRIVEN
static void irq_config_func_1(struct device *dev)
{
ARG_UNUSED(dev);
IRQ_CONNECT(UART_NS16550_PORT_1_IRQ,
CONFIG_UART_NS16550_PORT_1_IRQ_PRI,
uart_ns16550_isr, DEVICE_GET(uart_ns16550_1),
UART_IRQ_FLAGS);
irq_enable(UART_NS16550_PORT_1_IRQ);
}
#endif
#endif /* CONFIG_UART_NS16550_PORT_1 */
Reference in New Issue View Git Blame Copy Permalink