106 lines
3.3 KiB
ReStructuredText
106 lines
3.3 KiB
ReStructuredText
.. _usb_device_networking_setup:
|
|
|
|
USB Device Networking
|
|
#####################
|
|
|
|
.. contents::
|
|
:local:
|
|
:depth: 2
|
|
|
|
This page describes how to set up networking between a Linux host
|
|
and a Zephyr application running on USB supported devices.
|
|
|
|
The board is connected to Linux host using USB cable
|
|
and provides an Ethernet interface to the host.
|
|
The :ref:`sockets-echo-server-sample` application from the Zephyr source
|
|
distribution is run on supported board. The board is connected to a
|
|
Linux host using a USB cable providing an Ethernet interface to the host.
|
|
|
|
Basic Setup
|
|
***********
|
|
|
|
To communicate with the Zephyr application over a newly created Ethernet
|
|
interface, we need to assign IP addresses and set up a routing table for
|
|
the Linux host.
|
|
After plugging a USB cable from the board to the Linux host, the
|
|
``cdc_ether`` driver registers a new Ethernet device with a provided MAC
|
|
address.
|
|
|
|
You can check that network device is created and MAC address assigned by
|
|
running dmesg from the Linux host.
|
|
|
|
.. code-block:: console
|
|
|
|
cdc_ether 1-2.7:1.0 eth0: register 'cdc_ether' at usb-0000:00:01.2-2.7, CDC Ethernet Device, 00:00:5e:00:53:01
|
|
|
|
We need to set it up and assign IP addresses as explained in the following
|
|
section.
|
|
|
|
Choosing IP addresses
|
|
=====================
|
|
|
|
To establish network connection to the board we need to choose IP address
|
|
for the interface on the Linux host.
|
|
|
|
It make sense to choose addresses in the same subnet we have in Zephyr
|
|
application. IP addresses usually set in the project configuration files
|
|
and may be checked also from the shell with following commands. Connect
|
|
a serial console program (such as puTTY) to the board, and enter this
|
|
command to the Zephyr shell:
|
|
|
|
.. code-block:: console
|
|
|
|
shell> net iface
|
|
|
|
Interface 0xa800e580 (Ethernet)
|
|
===============================
|
|
Link addr : 00:00:5E:00:53:00
|
|
MTU : 1500
|
|
IPv6 unicast addresses (max 2):
|
|
fe80::200:5eff:fe00:5300 autoconf preferred infinite
|
|
2001:db8::1 manual preferred infinite
|
|
...
|
|
IPv4 unicast addresses (max 1):
|
|
192.0.2.1 manual preferred infinite
|
|
|
|
This command shows that one IPv4 address and two IPv6 addresses have
|
|
been assigned to the board. We can use either IPv4 or IPv6 for network
|
|
connection depending on the board network configuration.
|
|
|
|
Next step is to assign IP addresses to the new Linux host interface, in
|
|
the following steps ``enx00005e005301`` is the name of the interface on my
|
|
Linux system.
|
|
|
|
Setting IPv4 address and routing
|
|
================================
|
|
|
|
.. code-block:: console
|
|
|
|
# ip address add dev enx00005e005301 192.0.2.2
|
|
# ip link set enx00005e005301 up
|
|
# ip route add 192.0.2.0/24 dev enx00005e005301
|
|
|
|
Setting IPv6 address and routing
|
|
================================
|
|
|
|
.. code-block:: console
|
|
|
|
# ip address add dev enx00005e005301 2001:db8::2
|
|
# ip link set enx00005e005301 up
|
|
# ip -6 route add 2001:db8::/64 dev enx00005e005301
|
|
|
|
Testing connection
|
|
******************
|
|
|
|
From the host we can test the connection by pinging Zephyr IP address of
|
|
the board with:
|
|
|
|
.. code-block:: console
|
|
|
|
$ ping 192.0.2.1
|
|
PING 192.0.2.1 (192.0.2.1) 56(84) bytes of data.
|
|
64 bytes from 192.0.2.1: icmp_seq=1 ttl=64 time=2.30 ms
|
|
64 bytes from 192.0.2.1: icmp_seq=2 ttl=64 time=1.43 ms
|
|
64 bytes from 192.0.2.1: icmp_seq=3 ttl=64 time=2.45 ms
|
|
...
|