157 lines
3.3 KiB
Plaintext
157 lines
3.3 KiB
Plaintext
# LIS2DH Three Axis Accelerometer configuration options
|
|
|
|
# Copyright (c) 2017 Intel Corporation
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
menuconfig LIS2DH
|
|
bool "LIS2DH Three Axis Accelerometer"
|
|
depends on I2C || SPI
|
|
help
|
|
Enable SPI/I2C-based driver for LIS2DH, LIS3DH, LSM303DLHC,
|
|
LIS2DH12, LSM303AGR triaxial accelerometer sensors.
|
|
|
|
if LIS2DH
|
|
|
|
choice LIS2DH_TRIGGER_MODE
|
|
prompt "Trigger mode"
|
|
help
|
|
Specify the type of triggering to be used by the driver.
|
|
|
|
config LIS2DH_TRIGGER_NONE
|
|
bool "No trigger"
|
|
|
|
config LIS2DH_TRIGGER_GLOBAL_THREAD
|
|
bool "Use global thread"
|
|
depends on GPIO
|
|
select LIS2DH_TRIGGER
|
|
|
|
config LIS2DH_TRIGGER_OWN_THREAD
|
|
bool "Use own thread"
|
|
depends on GPIO
|
|
select LIS2DH_TRIGGER
|
|
|
|
endchoice
|
|
|
|
config LIS2DH_TRIGGER
|
|
bool
|
|
|
|
config LIS2DH_THREAD_PRIORITY
|
|
int "Thread priority"
|
|
depends on LIS2DH_TRIGGER_OWN_THREAD
|
|
default 10
|
|
help
|
|
Priority of thread used by the driver to handle interrupts.
|
|
|
|
config LIS2DH_THREAD_STACK_SIZE
|
|
int "Thread stack size"
|
|
depends on LIS2DH_TRIGGER_OWN_THREAD
|
|
default 1024
|
|
help
|
|
Stack size of thread used by the driver to handle interrupts.
|
|
|
|
choice LIS2DH_ACCEL_RANGE
|
|
prompt "Acceleration measurement range"
|
|
default LIS2DH_ACCEL_RANGE_RUNTIME
|
|
help
|
|
Initial measurement full scale range for acceleration values.
|
|
|
|
config LIS2DH_ACCEL_RANGE_RUNTIME
|
|
bool "Set at runtime"
|
|
|
|
config LIS2DH_ACCEL_RANGE_2G
|
|
bool "+/-2g"
|
|
|
|
config LIS2DH_ACCEL_RANGE_4G
|
|
bool "+/-4g"
|
|
|
|
config LIS2DH_ACCEL_RANGE_8G
|
|
bool "+/-8g"
|
|
|
|
config LIS2DH_ACCEL_RANGE_16G
|
|
bool "+/-16g"
|
|
|
|
endchoice
|
|
|
|
choice LIS2DH_OPER_MODE
|
|
prompt "Operation mode"
|
|
default LIS2DH_OPER_MODE_NORMAL
|
|
help
|
|
Choose between high resolution, normal or low power operation
|
|
mode for chip at init.
|
|
|
|
config LIS2DH_OPER_MODE_HIGH_RES
|
|
bool "high resolution (12 bit)"
|
|
|
|
config LIS2DH_OPER_MODE_NORMAL
|
|
bool "normal (10 bit)"
|
|
|
|
config LIS2DH_OPER_MODE_LOW_POWER
|
|
bool "low power (8 bit)"
|
|
|
|
endchoice
|
|
|
|
choice LIS2DH_ODR
|
|
prompt "Output data rate frequency"
|
|
default LIS2DH_ODR_RUNTIME
|
|
help
|
|
Initial data rate frequency of acceleration data at initialization.
|
|
Supported values:
|
|
1Hz, 10Hz, 25Hz, 50Hz, 100Hz, 200Hz, 400Hz in all power modes
|
|
1620Hz, 5376Hz in low power mode only
|
|
1344Hz in normal power mode
|
|
|
|
config LIS2DH_ODR_RUNTIME
|
|
bool "Set at runtime"
|
|
|
|
config LIS2DH_ODR_1
|
|
bool "1Hz"
|
|
|
|
config LIS2DH_ODR_2
|
|
bool "10Hz"
|
|
|
|
config LIS2DH_ODR_3
|
|
bool "25Hz"
|
|
|
|
config LIS2DH_ODR_4
|
|
bool "50Hz"
|
|
|
|
config LIS2DH_ODR_5
|
|
bool "100Hz"
|
|
|
|
config LIS2DH_ODR_6
|
|
bool "200Hz"
|
|
|
|
config LIS2DH_ODR_7
|
|
bool "400Hz"
|
|
|
|
config LIS2DH_ODR_8
|
|
bool "1.6KHz"
|
|
depends on LIS2DH_OPER_MODE_LOW_POWER
|
|
|
|
config LIS2DH_ODR_9_NORMAL
|
|
bool "1.25KHz"
|
|
depends on LIS2DH_OPER_MODE_NORMAL || LIS2DH_OPER_MODE_HIGH_RES
|
|
|
|
config LIS2DH_ODR_9_LOW
|
|
bool "5KHz"
|
|
depends on LIS2DH_OPER_MODE_LOW_POWER
|
|
|
|
endchoice
|
|
|
|
config LIS2DH_BLOCK_DATA_UPDATE
|
|
bool "Output registers not updated until MSB and LSB read"
|
|
|
|
config LIS2DH_MEASURE_TEMPERATURE
|
|
bool "Enable temperature measurements"
|
|
select LIS2DH_BLOCK_DATA_UPDATE
|
|
help
|
|
The temperature sensor is most suitable for measuring
|
|
relative temperature. For example, it is X degrees C
|
|
cooler or warmer.
|
|
Each chip has an offset. This offset must be applied
|
|
to the result. The offset can be obtained by comparing the
|
|
the reported temperature to a reference.
|
|
This option does not apply to the LSM330DLHC.
|
|
|
|
endif # LIS2DH
|