459 lines
26 KiB
ReStructuredText
459 lines
26 KiB
ReStructuredText
.. _zephyr_1.7:
|
|
|
|
Zephyr Kernel 1.7.0
|
|
####################
|
|
|
|
We are pleased to announce the release of Zephyr kernel version 1.7.0. This
|
|
release continues refinement of the unified kernel introduced with the 1.6.0
|
|
kernel release, simplifying the overall Zephyr architecture and programming
|
|
interfaces. This is the last release that will support the deprecated legacy
|
|
nano- and micro-kernel APIs found in the 1.5.0 release and earlier.
|
|
|
|
This release introduces a new native IP stack, replacing the legacy uIP stack,
|
|
maintaining the legacy functionality, adding additional capabilities, and allowing
|
|
future improvements.
|
|
|
|
We have introduced support for the RISC V and Xtensa architectures and now
|
|
support 6 architectures in total.
|
|
|
|
Device tree support for ARM based boards added. The initial
|
|
device tree support includes flash/sram base address and UART devices. Board
|
|
support includes NXP Kinetis based SoCs, ARM Beetle, TI CC3200 LaunchXL, and
|
|
STML32L476 based SoCs. Plan is to add support for other architectures and
|
|
expand device support in upcoming Zephyr releases.
|
|
|
|
The following sections provide a detailed list of changes, by component, since
|
|
kernel version 1.6.0.
|
|
|
|
Kernel
|
|
******
|
|
|
|
* Introduction of k_poll API: k_poll() is similar to the POSIX poll() API in
|
|
spirit in that it allows a single thread to monitor multiple events without
|
|
actively polling them, but rather pending for one or more to become ready.
|
|
* Optimized memory use of some thread fields
|
|
* Remove usage of micro/nano kernel terminology from kernel code and introduced
|
|
a legacy option to enable/disable legacy APIs. (using legacy.h)
|
|
|
|
|
|
Architectures
|
|
*************
|
|
|
|
* ARM: Added support for device tree
|
|
* ARM: Fixed exception priority access on Cortex M0(+)
|
|
* ARM: Refactored to use CMSIS
|
|
|
|
Boards
|
|
******
|
|
|
|
* Added ARM MPS2_AN385 board
|
|
* Added Atmel SAM E70 Xplained board
|
|
* Added Nordic pca10056 PDK board
|
|
* Added NXP FRDM-KW41Z board
|
|
* Added ST Nucleo-F334R8, Nucleo-L476G, STM3210C-EVAL, and STM32373C-EVAL boards
|
|
* Added Panther and tinyTILE boards, based on Quark SE C1000 and Intel Curie
|
|
* Added support for Zedboard Pulpino, a RISC V based board
|
|
* Added Qemu target for RISC V and a simulator target for the Xtensa architecture.
|
|
|
|
Drivers and Sensors
|
|
*******************
|
|
|
|
* Added Atmel SAM pmc, gpio, uart, and ethernet drivers
|
|
* Added STM32F3x clock, flash, gpio, pinmux drivers
|
|
* Added stm32cube pwm and clock drivers
|
|
* Added cc3200 gpio driver
|
|
* Added mcr20a ieee802154 driver
|
|
* Added mcux pinmux, gpio, uart, and spi drivers
|
|
* Added Beetle clock control and watchdog drivers
|
|
|
|
Networking
|
|
**********
|
|
|
|
This version removes the legacy uIP stack and introduces a new native IP stack.
|
|
Because of this there is lot of changes in the code base. The native IP stack
|
|
will support the same functionality as the legacy IP stack found in 1.6, and
|
|
add new networking features which are described below.
|
|
|
|
* IP stack code is moved to subsys/net/ip directory.
|
|
* IP stack supports both IPv6 and IPv4, and they can be enabled simultaneously.
|
|
* Multiple network technologies like Bluetooth IPSP and IEEE 802.15.4 can be
|
|
enabled simultaneously. No routing functionality is provided by IP stack
|
|
between enabled network technologies, applications need to decide where to
|
|
send the network packets.
|
|
* Network technologies are abstracted in IP layer 2 (L2) and presented to
|
|
rest of the system as network interfaces. There exists L2 driver for
|
|
Ethernet, Bluetooth and IEEE 802.15.4.
|
|
* Created Bluetooth Internet Protocol Support Profile (IPSP) support. It will
|
|
provide IPv6 connection over Bluetooth connection oriented channel (L2CAP).
|
|
* Created DHCPv4 support.
|
|
* Created CoAP implementation called ZoAP which replaces uIP based one.
|
|
* Updated 6Lo implementation to support both Bluetooth and IEEE 802.15.4
|
|
* Created application API (net_context) for creating connections and
|
|
transferring data to external systems.
|
|
* Added sample application (wpanusb) for exporting IEEE 802.15.4 radio over
|
|
USB to external operating systems like Linux.
|
|
* Added DNS client library.
|
|
* Updated TCP implementation.
|
|
* Created MQTT publisher support.
|
|
* Created network test generator (zperf).
|
|
* Created telnet console support.
|
|
* Created IRC client sample application.
|
|
* Created HTTP server and client sample applications.
|
|
* Created net-shell module for interacting with network sub-system.
|
|
* Created ieee15_4 shell module for dedicated interaction with
|
|
IEEE 802.15.4 Soft MAC.
|
|
* Created network management API for generic network settings request as well
|
|
as a network event notification system (sender/listener).
|
|
* Redesigned buffer & pool allocation API.
|
|
|
|
Bluetooth
|
|
*********
|
|
|
|
* Redesigned buffer pools for smaller memory consumption
|
|
* Redesigned thread model for smaller memory consumption
|
|
* Utilized new k_poll API to consolidate all TX threads into a single one
|
|
* Added more SDP functionality
|
|
* Improved RFCOMM support
|
|
* Reduced latencies in the Controller
|
|
* Added SPI HCI driver
|
|
|
|
Libraries
|
|
*********
|
|
|
|
* Updated mbedTLS library
|
|
* Updated TinyCrypt to version 0.2.5
|
|
|
|
HALs
|
|
****
|
|
|
|
* Updated FAT FS to rev 0.12b
|
|
* Updated Nordic MDK header files
|
|
* Updated QMSI to 1.4 RC3
|
|
* Imported Atmel SDK (ASF) for SAM E70 and SAM3X
|
|
* Imported Nordic SDK HAL and 802.15.4 radio driver
|
|
* Renamed NXP KSDK to MCUX
|
|
* Imported NXP MCUX for KW41Z
|
|
* Imported Segger J-Link RTT library
|
|
* Imported stm32cube for F4 and L4
|
|
|
|
Documentation
|
|
*************
|
|
|
|
* General improvements and additions to kernel component docs
|
|
* Moved supported board information back to the website site.
|
|
* New website documentation theme to go with the new zephyrproject.org site.
|
|
* New local-content generation theme (read-the-docs)
|
|
* General spelling checks and organizational improvements.
|
|
* Site-wide glossary added.
|
|
* Porting guides added.
|
|
* Sample README files converted to documents included in the website.
|
|
* Improved consistency of :ref:`boards` and :ref:`samples-and-demos`.
|
|
|
|
|
|
JIRA Related Items
|
|
******************
|
|
|
|
|
|
.. comment List derived from https://jira.zephyrproject.org/issues/?filter=10345
|
|
|
|
* :jira:`ZEP-19` - IPSP node support
|
|
* :jira:`ZEP-145` - no 'make flash' for Arduino Due
|
|
* :jira:`ZEP-328` - HW Encryption Abstraction
|
|
* :jira:`ZEP-359` - Move QEMU handling to a central location
|
|
* :jira:`ZEP-365` - Zephyr's MQTT library
|
|
* :jira:`ZEP-437` - TCP/IP API
|
|
* :jira:`ZEP-513` - extern declarations of small microkernel objects in designated sections require __attribute__((section)) in gp-enabled systems
|
|
* :jira:`ZEP-591` - MQTT Port to New IP Stack
|
|
* :jira:`ZEP-604` - In coap_server sample app, CoAP resource separate is not able to send separate response
|
|
* :jira:`ZEP-613` - TCP/UDP client and server mode functionality
|
|
* :jira:`ZEP-641` - Bluetooth Eddystone sample does not correctly implement Eddystone beacon
|
|
* :jira:`ZEP-648` - New CoAP Implementation
|
|
* :jira:`ZEP-664` - Extend spi_qmsi_ss driver to support save/restore peripheral context
|
|
* :jira:`ZEP-665` - Extend gpio_qmsi_ss driver to support save/restore peripheral context
|
|
* :jira:`ZEP-666` - Extend i2c_qmsi_ss driver to support save/restore peripheral context
|
|
* :jira:`ZEP-667` - Extend adc_qmsi_ss driver to support save/restore peripheral context
|
|
* :jira:`ZEP-686` - docs: Info in Application Development Primer and Developing an Application and the Build System is largely duplicated
|
|
* :jira:`ZEP-706` - cannot set debug breakpoints on ARC side of Arduino 101
|
|
* :jira:`ZEP-719` - Add ksdk uart shim driver
|
|
* :jira:`ZEP-734` - Port AES-CMAC-PRF-128 [RFC 4615] encryption library for Thread support
|
|
* :jira:`ZEP-742` - nRF5x Series: System Clock driver using NRF_RTC
|
|
* :jira:`ZEP-744` - USB WebUSB
|
|
* :jira:`ZEP-748` - Enable mbedtls_sslclient sample to run on quark se board
|
|
* :jira:`ZEP-759` - Add preliminary support for Atmel SAM E70 (Cortex-M7) chipset family and SAM E70 Xplained board
|
|
* :jira:`ZEP-788` - UDP
|
|
* :jira:`ZEP-789` - IPv4
|
|
* :jira:`ZEP-790` - ICMPv4
|
|
* :jira:`ZEP-791` - TCP
|
|
* :jira:`ZEP-792` - ARP
|
|
* :jira:`ZEP-793` - DNS Resolver
|
|
* :jira:`ZEP-794` - Requirements for Internet Hosts - Communication Layers
|
|
* :jira:`ZEP-796` - DHCPv4
|
|
* :jira:`ZEP-798` - IPv6
|
|
* :jira:`ZEP-799` - HTTP over TLS
|
|
* :jira:`ZEP-801` - DNS Extensions to support IPv6
|
|
* :jira:`ZEP-804` - IPv6 Addressing Architecture
|
|
* :jira:`ZEP-805` - Internet Control Message Protocol (ICMP) v6
|
|
* :jira:`ZEP-807` - Neighbor Discovery for IPv6
|
|
* :jira:`ZEP-808` - IPv6 Stateless Autoconfiguration (SLAAC)
|
|
* :jira:`ZEP-809` - IPv6 over 802.15.4
|
|
* :jira:`ZEP-811` - The Trickle Algorithm
|
|
* :jira:`ZEP-812` - Compression Format for IPv6 over 802.15.4
|
|
* :jira:`ZEP-813` - RPL: IPv6 Routing Protocol
|
|
* :jira:`ZEP-814` - Routing Metrics used in Path Selection
|
|
* :jira:`ZEP-815` - Objective Function Zero for RPL
|
|
* :jira:`ZEP-816` - Minimum Rank with Hysteresis (RPL)
|
|
* :jira:`ZEP-818` - CoAP working over the new IP stack
|
|
* :jira:`ZEP-820` - HTTP v1.1 Server Sample
|
|
* :jira:`ZEP-823` - New IP Stack - Documentation
|
|
* :jira:`ZEP-824` - Network Device Driver Porting Guide
|
|
* :jira:`ZEP-825` - Porting guide for old-to-new IP Stack APIs
|
|
* :jira:`ZEP-827` - HTTP Client sample application
|
|
* :jira:`ZEP-830` - ICMPv6 Parameter Problem Support
|
|
* :jira:`ZEP-832` - Hop-by-Hop option handling
|
|
* :jira:`ZEP-847` - Network protocols must be moved to subsys/net/lib
|
|
* :jira:`ZEP-854` - CoAP with DTLS sample
|
|
* :jira:`ZEP-859` - Migrate ENC28J60 driver to YAIP IP stack
|
|
* :jira:`ZEP-865` - convert filesystem sample to a runnable test
|
|
* :jira:`ZEP-872` - Unable to flash Zephyr on Arduino 101 using Ubuntu and following wiki instructions
|
|
* :jira:`ZEP-873` - DMA API Update
|
|
* :jira:`ZEP-875` - 6LoWPAN - Context based compression support
|
|
* :jira:`ZEP-876` - 6LoWPAN - Offset based Reassembly of 802.15.4 packets
|
|
* :jira:`ZEP-879` - 6LoWPAN - Stateless Address Autoconfiguration
|
|
* :jira:`ZEP-882` - 6LoWPAN - IPv6 Next Header Compression
|
|
* :jira:`ZEP-883` - IP Stack L2 Interface Management API
|
|
* :jira:`ZEP-884` - 802.15.4 - CSMA-CA Radio protocol support
|
|
* :jira:`ZEP-885` - 802.15.4 - Beacon frame support
|
|
* :jira:`ZEP-886` - 802.15.4 - MAC command frame support
|
|
* :jira:`ZEP-887` - 802.15.4 - Management service: RFD level support
|
|
* :jira:`ZEP-911` - Refine thread priorities & locking
|
|
* :jira:`ZEP-919` - Purge obsolete microkernel & nanokernel code
|
|
* :jira:`ZEP-929` - Verify the preempt-thread-only and coop-thread-only configurations
|
|
* :jira:`ZEP-931` - Finalize kernel file naming & locations
|
|
* :jira:`ZEP-936` - Adapt drivers to unified kernel
|
|
* :jira:`ZEP-937` - Adapt networking to unified kernel
|
|
* :jira:`ZEP-946` - Galileo Gen1 board support dropped?
|
|
* :jira:`ZEP-951` - CONFIG_GDB_INFO build not working on ARM
|
|
* :jira:`ZEP-953` - CONFIG_HPET_TIMER_DEBUG build warning
|
|
* :jira:`ZEP-958` - simplify pinmux interface and merge the pinmux_dev into one single API
|
|
* :jira:`ZEP-964` - Add a (hidden?) Kconfig option for disabling legacy API
|
|
* :jira:`ZEP-975` - DNS client port to new IP stack
|
|
* :jira:`ZEP-1012` - NATS client port to new IP stack
|
|
* :jira:`ZEP-1038` - Hard real-time interrupt support
|
|
* :jira:`ZEP-1060` - Contributor guide for documentation missing
|
|
* :jira:`ZEP-1103` - Propose and implement synchronization flow for multicore power management
|
|
* :jira:`ZEP-1165` - support enums as IRQ line argument in IRQ_CONNECT()
|
|
* :jira:`ZEP-1172` - Update logger Api to allow using a hook for SYS_LOG_BACKEND_FN function
|
|
* :jira:`ZEP-1177` - Reduce Zephyr's Dependency on Host Tools
|
|
* :jira:`ZEP-1179` - Build issues when compiling with LLVM from ISSM (icx)
|
|
* :jira:`ZEP-1189` - SoC I2C peripheral of the Quark SE cannot be used from the ARC core
|
|
* :jira:`ZEP-1190` - SoC SPI peripheral of the Quark SE cannot be used from the ARC core
|
|
* :jira:`ZEP-1222` - Add save/restore support to ARC core
|
|
* :jira:`ZEP-1223` - Add save/restore support to arcv2_irq_unit
|
|
* :jira:`ZEP-1224` - Add save/restore support to arcv2_timer_0/sys_clock
|
|
* :jira:`ZEP-1230` - Optimize interrupt return code on ARC.
|
|
* :jira:`ZEP-1233` - mbedDTLS DTLS client stability does not work on top of the tree for the net branch
|
|
* :jira:`ZEP-1251` - Abstract driver re-entrancy code
|
|
* :jira:`ZEP-1267` - Echo server crashes upon reception of router advertisement
|
|
* :jira:`ZEP-1276` - Move disk_access_* out of file system subsystem
|
|
* :jira:`ZEP-1283` - compile option to skip gpio toggle in samples/power/power_mgr
|
|
* :jira:`ZEP-1284` - Remove arch/arm/core/gdb_stub.S and all the abstractions it introduced
|
|
* :jira:`ZEP-1288` - Define _arc_v2_irq_unit device
|
|
* :jira:`ZEP-1292` - Update external mbed TLS library to latest version (2.4.0)
|
|
* :jira:`ZEP-1300` - ARM LTD V2M Beetle Support [Phase 2]
|
|
* :jira:`ZEP-1304` - Define device tree bindings for NXP Kinetis K64F
|
|
* :jira:`ZEP-1305` - Add DTS/DTB targets to build infrastructure
|
|
* :jira:`ZEP-1306` - Create DTS/DTB parser
|
|
* :jira:`ZEP-1307` - Plumbing the DTS configuration
|
|
* :jira:`ZEP-1308` - zephyr thread function k_sleep doesn't work with nrf51822
|
|
* :jira:`ZEP-1320` - Update Architecture Porting Guide
|
|
* :jira:`ZEP-1321` - Glossary of Terms needs updating
|
|
* :jira:`ZEP-1323` - Eliminate references to fiber, task, and nanokernel under ./include
|
|
* :jira:`ZEP-1324` - Get rid of references to CONFIG_NANOKERNEL
|
|
* :jira:`ZEP-1325` - Eliminate TICKLESS_IDLE_SUPPORTED option
|
|
* :jira:`ZEP-1327` - Eliminate obsolete kernel directories
|
|
* :jira:`ZEP-1329` - Rename kernel APIs that have nano\_ prefixes
|
|
* :jira:`ZEP-1334` - Add make debug support for QEMU-based boards
|
|
* :jira:`ZEP-1337` - Relocate event logger files
|
|
* :jira:`ZEP-1338` - Update external fs with new FATFS revision 0.12b
|
|
* :jira:`ZEP-1342` - legacy/kernel/test_early_sleep/ fails on EMSK
|
|
* :jira:`ZEP-1347` - sys_bitfield_*() take unsigned long* vs memaddr_t
|
|
* :jira:`ZEP-1351` - FDRM k64f SPI does not work
|
|
* :jira:`ZEP-1355` - Connection Failed to be Established
|
|
* :jira:`ZEP-1357` - iot/dns: Client is broken
|
|
* :jira:`ZEP-1358` - BMI160 accelerometer gives 0 on all axes
|
|
* :jira:`ZEP-1361` - IP stack is broken
|
|
* :jira:`ZEP-1363` - Missing wiki board support page for arm/arduino_101_ble
|
|
* :jira:`ZEP-1365` - Missing wiki board support page for arm/c3200_launchxl
|
|
* :jira:`ZEP-1370` - There's a wiki page for arduino_due but no zephyr/boards support folder
|
|
* :jira:`ZEP-1374` - Add ksdk spi shim driver
|
|
* :jira:`ZEP-1387` - Add a driver for Atmel ataes132a HW Crypto module
|
|
* :jira:`ZEP-1389` - Add support for KW41 SoC
|
|
* :jira:`ZEP-1390` - Add support for FRDM-KW41Z
|
|
* :jira:`ZEP-1393` - Add ksdk pinmux driver
|
|
* :jira:`ZEP-1394` - Add ksdk gpio driver
|
|
* :jira:`ZEP-1395` - Add data ready trigger to FXOS8700 driver
|
|
* :jira:`ZEP-1401` - Enhance ready queue cache and interrupt exit code to reduce interrupt latency.
|
|
* :jira:`ZEP-1403` - remove CONFIG_OMIT_FRAME_POINTER from ARC boards
|
|
* :jira:`ZEP-1405` - function l2cap_br_conn_req in /subsys/bluetooth/host/l2cap_br.c references uninitialized pointer
|
|
* :jira:`ZEP-1406` - Update sensor driver paths in wiki
|
|
* :jira:`ZEP-1408` - quark_se_c1000_ss enter_arc_state() might need cc and memory clobber
|
|
* :jira:`ZEP-1411` - Deprecate device_sync_call API and use semaphore directly
|
|
* :jira:`ZEP-1413` - [ARC] test/legacy/kernel/test_tickless/microkernel fails to build
|
|
* :jira:`ZEP-1415` - drivers/timer/* code comments still refer to micro/nano kernel
|
|
* :jira:`ZEP-1418` - Add support for Nordic nRF52840 and its DK
|
|
* :jira:`ZEP-1419` - SYS_LOG macros cause potentially bad behavior due to printk/printf selection
|
|
* :jira:`ZEP-1420` - Make the time spent with interrupts disabled deterministic
|
|
* :jira:`ZEP-1421` - BMI160 gyroscope driver stops reporting after 1-5 minutes
|
|
* :jira:`ZEP-1422` - Arduino_101 doesn't response ipv6 ping request after enable echo_client ipv6
|
|
* :jira:`ZEP-1427` - wpanusb dongle / 15.4 communication instability
|
|
* :jira:`ZEP-1429` - NXP MCR20A Driver
|
|
* :jira:`ZEP-1432` - ksdk pinmux driver should expose the public pinmux API
|
|
* :jira:`ZEP-1434` - menuconfig screen shots show nanokernel options
|
|
* :jira:`ZEP-1437` - AIO: Fail to retrieve pending interrupt in ISR
|
|
* :jira:`ZEP-1440` - Kconfig choice for MINIMAL_LIBC vs NEWLIB_LIBC is not selectable
|
|
* :jira:`ZEP-1442` - Samples/net/dhcpv4_client: Build fail as No rule to make target prj\_.conf
|
|
* :jira:`ZEP-1443` - Samples/net/zperf: Build fail as net_private.h can not be found
|
|
* :jira:`ZEP-1448` - Samples/net/mbedtls_sslclient:Build fail as net/ip_buf.h can not be found
|
|
* :jira:`ZEP-1449` - samples: logger_hook
|
|
* :jira:`ZEP-1456` - Asserts on nrf51 running Bluetooth hci_uart sample
|
|
* :jira:`ZEP-1457` - Add SPDX Tags to Zephyr license boilerplate
|
|
* :jira:`ZEP-1460` - Sanity check reports some qemu step failures as 'build_error'
|
|
* :jira:`ZEP-1461` - Add zephyr support to openocd upstream
|
|
* :jira:`ZEP-1467` - Cleanup misc/ and move features to subsystems in subsys/
|
|
* :jira:`ZEP-1473` - ARP cache confused by use of gateway.
|
|
* :jira:`ZEP-1474` - BLE Connection Parameter Request/Response Processing
|
|
* :jira:`ZEP-1475` - k_free documentation should specify that NULL is valid
|
|
* :jira:`ZEP-1476` - echo_client display port unreachable
|
|
* :jira:`ZEP-1480` - Update supported distros in getting started guide
|
|
* :jira:`ZEP-1481` - Bluetooth fails to init
|
|
* :jira:`ZEP-1483` - H:4 HCI driver (h4.c) should rely on UART flow control to avoid dropping packets
|
|
* :jira:`ZEP-1487` - I2C_SS: I2C doesn't set device busy before starting data transfer
|
|
* :jira:`ZEP-1488` - SPI_SS: SPI doesn't set device busy before starting data transfer
|
|
* :jira:`ZEP-1489` - [GATT] Nested Long Characteristic Value Reliable Writes
|
|
* :jira:`ZEP-1490` - [PTS] TC_CONN_CPUP_BV_04_C test case is failing
|
|
* :jira:`ZEP-1492` - Add Atmel SAM family GMAC Ethernet driver
|
|
* :jira:`ZEP-1493` - Zephyr project documentation copyright
|
|
* :jira:`ZEP-1495` - Networking API details documentation is missing
|
|
* :jira:`ZEP-1496` - gpio_pin_enable_callback error
|
|
* :jira:`ZEP-1497` - Cortex-M0 port exception and interrupt priority setting and getting is broken
|
|
* :jira:`ZEP-1507` - fxos8700 broken gpio_callback implementation
|
|
* :jira:`ZEP-1512` - doc-theme has its own conf.py
|
|
* :jira:`ZEP-1514` - samples/bluetooth/ipsp build fail: net/ip_buf.h No such file or directory
|
|
* :jira:`ZEP-1525` - driver: gpio: GPIO driver still uses nano_timer
|
|
* :jira:`ZEP-1532` - Wrong accelerometer readings
|
|
* :jira:`ZEP-1536` - Convert documentation of PWM samples to RST
|
|
* :jira:`ZEP-1537` - Convert documentation of power management samples to RST
|
|
* :jira:`ZEP-1538` - Convert documentation of zoap samples to RST
|
|
* :jira:`ZEP-1539` - Create documentation in RST for all networking samples
|
|
* :jira:`ZEP-1540` - Convert Bluetooth samples to RST
|
|
* :jira:`ZEP-1542` - Multi Sessions HTTP Server sample
|
|
* :jira:`ZEP-1543` - HTTP Server sample with basic authentication
|
|
* :jira:`ZEP-1544` - Arduino_101 doesn't respond to ipv6 ping request after enable echo_server ipv6
|
|
* :jira:`ZEP-1545` - AON Counter : ISR triggered twice on ARC
|
|
* :jira:`ZEP-1546` - Bug in Zephyr OS high-precision timings sub-system (function sys_cycle_get_32())
|
|
* :jira:`ZEP-1547` - Add support for H7 crypto function and CT2 SMP auth flag
|
|
* :jira:`ZEP-1548` - Python script invocation is inconsistent
|
|
* :jira:`ZEP-1549` - k_cpu_sleep_mode unaligned byte address
|
|
* :jira:`ZEP-1554` - Xtensa integration
|
|
* :jira:`ZEP-1557` - RISC V Port
|
|
* :jira:`ZEP-1558` - Support of user private data pointer in Timer expiry function
|
|
* :jira:`ZEP-1559` - Implement _tsc_read for ARC architecture
|
|
* :jira:`ZEP-1562` - echo_server/echo_client examples hang randomly after some time of operation
|
|
* :jira:`ZEP-1563` - move board documentation for NRF51/NRF52 back to git tree
|
|
* :jira:`ZEP-1564` - 6lo uncompress_IPHC_header overwrites IPHC fields
|
|
* :jira:`ZEP-1566` - WDT: Interrupt is triggered multiple times
|
|
* :jira:`ZEP-1569` - net/tcp: TCP in server mode doesn't support multiple concurrent connections
|
|
* :jira:`ZEP-1570` - net/tcp: TCP in server mode is unable to close client connections
|
|
* :jira:`ZEP-1571` - Update "Changes from Version 1 Kernel" to include a "How-To Port Apps" section
|
|
* :jira:`ZEP-1572` - Update QMSI to 1.4
|
|
* :jira:`ZEP-1573` - net/tcp: User provided data in net_context_recv is not passed to callback
|
|
* :jira:`ZEP-1574` - Samples/net/dhcpv4_client: Build fail as undefined reference to net_mgmt_add_event_callback
|
|
* :jira:`ZEP-1579` - external links to zephyr technical docs are broken
|
|
* :jira:`ZEP-1581` - [nRF52832] Blinky hangs after some minutes
|
|
* :jira:`ZEP-1583` - ARC: warning: unmet direct dependencies (SOC_RISCV32_PULPINO || SOC_RISCV32_QEMU)
|
|
* :jira:`ZEP-1585` - legacy.h should be disabled in kernel.h with CONFIG_LEGACY_KERNEL=n
|
|
* :jira:`ZEP-1587` - sensor.h still uses legacy APIs and structs
|
|
* :jira:`ZEP-1588` - I2C doesn't work on Arduino 101
|
|
* :jira:`ZEP-1589` - Define yaml descriptions for UART devices
|
|
* :jira:`ZEP-1590` - echo_server run on FRDM-K64F displays BUS FAULT
|
|
* :jira:`ZEP-1591` - wiki: add Networking section and point https://wiki.zephyrproject.org/view/Network_Interfaces
|
|
* :jira:`ZEP-1592` - echo-server does not build with newlib
|
|
* :jira:`ZEP-1593` - /scripts/sysgen should create output using SPDX licensing tag
|
|
* :jira:`ZEP-1598` - samples/philosophers build failed unexpectedly @quark_d2000 section noinit will not fit in region RAM
|
|
* :jira:`ZEP-1601` - Console over Telnet
|
|
* :jira:`ZEP-1602` - IPv6 ping fails using sample application echo_server on FRDM-K64F
|
|
* :jira:`ZEP-1611` - Hardfault after a few echo requests (IPv6 over BLE)
|
|
* :jira:`ZEP-1614` - Use correct i2c device driver name
|
|
* :jira:`ZEP-1616` - Mix up between "network address" and "socket address" concepts in declaration of net_addr_pton()
|
|
* :jira:`ZEP-1617` - mbedTLS server/client failing to run on qemu
|
|
* :jira:`ZEP-1619` - Default value of NET_NBUF_RX_COUNT is too low, causes lock up on startup
|
|
* :jira:`ZEP-1623` - (Parts) of Networking docs still refer to 1.5 world model (with fibers and tasks) and otherwise not up to date
|
|
* :jira:`ZEP-1626` - SPI: spi cannot work in CPHA mode @ ARC
|
|
* :jira:`ZEP-1632` - TCP ACK packet should not be forwarded to application recv cb.
|
|
* :jira:`ZEP-1635` - MCR20A driver unstable
|
|
* :jira:`ZEP-1638` - No (public) analog of inet_ntop()
|
|
* :jira:`ZEP-1644` - Incoming connection handling for UDP is not exactly correct
|
|
* :jira:`ZEP-1645` - API to wait on multiple kernel objects
|
|
* :jira:`ZEP-1648` - Update links to wiki pages for board info back into the web docs
|
|
* :jira:`ZEP-1650` - make clean (or pristine) is not removing all artifacts of document generation
|
|
* :jira:`ZEP-1651` - i2c_dw malfunctioning due to various changes.
|
|
* :jira:`ZEP-1653` - build issue when compiling with LLVM in ISSM (altmacro)
|
|
* :jira:`ZEP-1654` - Build issues when compiling with LLVM(unknown attribute '_alloc_align_)
|
|
* :jira:`ZEP-1655` - Build issues when compiling with LLVM(memory pool)
|
|
* :jira:`ZEP-1656` - IPv6 over BLE no longer works after commit 2e9fd88
|
|
* :jira:`ZEP-1657` - Zoap doxygen documentation needs to be perfected
|
|
* :jira:`ZEP-1658` - IPv6 TCP low on buffers, stops responding after about 5 requests
|
|
* :jira:`ZEP-1662` - zoap_packet_get_payload() should return the payload length
|
|
* :jira:`ZEP-1663` - sanitycheck overrides user's environment for CCACHE
|
|
* :jira:`ZEP-1665` - pinmux: missing default pinmux driver config for quark_se_ss
|
|
* :jira:`ZEP-1669` - API documentation does not follow in-code documentation style
|
|
* :jira:`ZEP-1672` - flash: Flash device binding failed on Arduino_101_sss
|
|
* :jira:`ZEP-1674` - frdm_k64f: With Ethernet driver enabled, application can't start up without connected network cable
|
|
* :jira:`ZEP-1677` - SDK: BLE cannot be initialized/advertised with CONFIG_ARC_INIT=y on Arduino 101
|
|
* :jira:`ZEP-1681` - Save/restore debug registers during soc_sleep/soc_deep_sleep in c1000
|
|
* :jira:`ZEP-1692` - [PTS] GATT/SR/GPA/BV-11-C fails
|
|
* :jira:`ZEP-1701` - Provide an HTTP API
|
|
* :jira:`ZEP-1704` - BMI160 samples fails to run
|
|
* :jira:`ZEP-1706` - Barebone Panther board support
|
|
* :jira:`ZEP-1707` - [PTS] 7 SM/MAS cases fail
|
|
* :jira:`ZEP-1708` - [PTS] SM/MAS/PKE/BI-01-C fails
|
|
* :jira:`ZEP-1709` - [PTS] SM/MAS/PKE/BI-02-C fails
|
|
* :jira:`ZEP-1710` - Add TinyTILE board support
|
|
* :jira:`ZEP-1713` - xtensa: correct all checkpatch issues
|
|
* :jira:`ZEP-1716` - HTTP server sample that does not support up to 10 concurrent sessions.
|
|
* :jira:`ZEP-1717` - GPIO: GPIO LEVEL interrupt cannot work well in deep sleep mode
|
|
* :jira:`ZEP-1723` - Warnings in Network code/ MACROS, when built with ISSM's llvm/icx compiler
|
|
* :jira:`ZEP-1732` - sample of zoap_server runs error.
|
|
* :jira:`ZEP-1733` - Work on ZEP-686 led to regressions in docs on integration with 3rd-party code
|
|
* :jira:`ZEP-1745` - Bluetooth samples build failure
|
|
* :jira:`ZEP-1753` - sample of dhcpv4_client runs error on Arduino 101
|
|
* :jira:`ZEP-1754` - sample of coaps_server was tested failed on qemu
|
|
* :jira:`ZEP-1756` - net apps: [-Wpointer-sign] build warning raised when built with ISSM's llvm/icx compiler
|
|
* :jira:`ZEP-1758` - PLL2 is not correctly enabled in STM32F10x connectivity line SoC
|
|
* :jira:`ZEP-1763` - Nordic RTC timer driver not correct with tickless idle
|
|
* :jira:`ZEP-1764` - samples: sample cases use hard code device name, such as "GPIOB" "I2C_0"
|
|
* :jira:`ZEP-1768` - samples: cases miss testcase.ini
|
|
* :jira:`ZEP-1774` - Malformed packet included with IPv6 over 802.15.4
|
|
* :jira:`ZEP-1778` - tests/power: multicore case won't work as expected
|
|
* :jira:`ZEP-1786` - TCP does not work on Arduino 101 board.
|
|
* :jira:`ZEP-1787` - kernel event logger build failed with "CONFIG_LEGACY_KERNEL=n"
|
|
* :jira:`ZEP-1789` - ARC: "samples/logger-hook" crashed __memory_error from sys_ring_buf_get
|
|
* :jira:`ZEP-1799` - timeout_order_test _ASSERT_VALID_PRIO failed
|
|
* :jira:`ZEP-1803` - Error occurs when exercising dma_transfer_stop
|
|
* :jira:`ZEP-1806` - Build warnings with LLVM/icx (gdb_server)
|
|
* :jira:`ZEP-1809` - Build error in net/ip with LLVM/icx
|
|
* :jira:`ZEP-1810` - Build failure in net/lib/zoap with LLVM/icx
|
|
* :jira:`ZEP-1811` - Build error in net/ip/net_mgmt.c with LLVM/icx
|
|
* :jira:`ZEP-1839` - LL_ASSERT in event_common_prepareA
|
|
* :jira:`ZEP-1851` - Build warnings with obj_tracing
|
|
* :jira:`ZEP-1852` - LL_ASSERT in isr_radio_state_close()
|
|
* :jira:`ZEP-1855` - IP stack buffer allocation fails over time
|
|
* :jira:`ZEP-1858` - Zephyr NATS client fails to respond to server MSG
|
|
* :jira:`ZEP-1864` - llvm icx build warning in tests/drivers/uart/*
|
|
* :jira:`ZEP-1872` - samples/net: the HTTP client sample app must run on QEMU x86
|
|
* :jira:`ZEP-1877` - samples/net: the coaps_server sample app runs failed on Arduino 101
|
|
* :jira:`ZEP-1883` - Enabling Console on ARC Genuino 101
|
|
* :jira:`ZEP-1890` - Bluetooth IPSP sample: Too small user data size
|
|
|
|
|