121 lines
3.8 KiB
Plaintext
121 lines
3.8 KiB
Plaintext
#
|
|
# Copyright (c) 2017 Linaro Limited
|
|
#
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
#
|
|
|
|
# The following blog post is an excellent resource about pulse timing:
|
|
#
|
|
# https://wp.josh.com/2014/05/13/ws2812-neopixels-are-not-so-finicky-once-you-get-to-know-them/
|
|
|
|
menuconfig WS2812_STRIP
|
|
bool "Enable WS2812 (and compatible) LED strip driver"
|
|
depends on SPI
|
|
help
|
|
Enable LED strip driver for daisy chains of WS2812-ish
|
|
(or WS2812B, WS2813, SK6812, or compatible) devices.
|
|
These devices have a one-wire communications interface
|
|
which encodes bits using pulses. Short pulses indicate
|
|
zero bits, and long pulses indicate ones; refer to the
|
|
chip datasheets for precise specifications. To implement
|
|
this in a multitasking operating system, this driver
|
|
generates the pulses using a SPI peripheral.
|
|
|
|
if WS2812_STRIP
|
|
|
|
config WS2812_STRIP_NAME
|
|
string "Driver name"
|
|
default "ws2812_strip"
|
|
help
|
|
Device name for WS2812 LED strip.
|
|
|
|
config WS2812_STRIP_SPI_DEV_NAME
|
|
string "SPI master to use to drive the strip"
|
|
default ""
|
|
help
|
|
Specify the device name of the SPI master which the
|
|
WS2812 driver should use to control the LED strip.
|
|
The MOSI pin of this SPI peripheral should be connected
|
|
to the signal pin for the first chip in the strip.
|
|
Examples: SPI_0, SPI_1, etc.
|
|
|
|
config WS2812_STRIP_SPI_BAUD_RATE
|
|
int "Baud rate to use to drive LED strip"
|
|
default 5250000
|
|
help
|
|
SPI clock rate, in Hz, to use while driving the strip.
|
|
The baud rate must be chosen carefully together with the
|
|
WS2812_STRIP_SPI_ONE_FRAME and WS2812_STRIP_SPI_ZERO_FRAME
|
|
values so that the transmitted frames meet the chipset
|
|
pulse widths for one and zero bits. If unsure, keep the default,
|
|
but enable SPI debug logging for your device and make sure the
|
|
configuration is matched exactly at runtime.
|
|
|
|
config WS2812_STRIP_ONE_FRAME
|
|
hex "SPI frame to shift out to signal a one bit"
|
|
default 0x7c
|
|
help
|
|
When shifted out at the configured clock frequency,
|
|
this must generate a pulse whose width fits within the chipset
|
|
specifications for T1H, and whose interpulse timing meets low
|
|
times. It is recommended that the first and last bits in the
|
|
frame be zero; this "encourages" SPI IPs to leave MOSI low
|
|
between frames.
|
|
|
|
config WS2812_STRIP_ZERO_FRAME
|
|
hex "SPI frame to shift out to signal a zero bit"
|
|
default 0x60
|
|
help
|
|
When shifted out at the configured clock frequency,
|
|
this must generate a pulse whose width fits within the chipset
|
|
specifications for T0H, and whose interpulse timing meets low
|
|
times. It is recommended that the first and last bits in the
|
|
frame be zero; this "encourages" SPI IPs to leave MOSI low
|
|
between frames.
|
|
|
|
# By default, we use GRBW [sic] (and ignore W).
|
|
comment "The following options determine channel data order on the wire."
|
|
|
|
config WS2812_RED_ORDER
|
|
int "Order in which a red pixel should be shifted out"
|
|
default 1
|
|
range 0 3
|
|
help
|
|
If the red channel is shifted out first, specify 0.
|
|
If second, specify 1, and so on.
|
|
|
|
config WS2812_GRN_ORDER
|
|
int "Order in which a green pixel should be shifted out"
|
|
default 0
|
|
range 0 3
|
|
help
|
|
If the green channel is shifted out first, specify 0.
|
|
If second, specify 1, and so on.
|
|
|
|
config WS2812_BLU_ORDER
|
|
int "Order in which a blue pixel should be shifted out"
|
|
default 2
|
|
range 0 3
|
|
help
|
|
If the blue channel is shifted out first, specify 0.
|
|
If second, specify 1, and so on.
|
|
|
|
config WS2812_HAS_WHITE_CHANNEL
|
|
bool "Does the chip have a white channel on wire?"
|
|
default y
|
|
help
|
|
If the chipset has a white channel, say y. White channels
|
|
are not used by the driver, but must be declared if expected
|
|
by the chip.
|
|
|
|
config WS2812_WHT_ORDER
|
|
int "Order in which a white pixel should be shifted out"
|
|
default 3
|
|
range 0 3
|
|
depends on WS2812_HAS_WHITE_CHANNEL
|
|
help
|
|
If the blue channel is shifted out first, specify 0.
|
|
If second, specify 1, and so on.
|
|
|
|
endif # WS2812_STRIP
|