147 lines
3.8 KiB
C
147 lines
3.8 KiB
C
/* sensor_sx9500.c - Driver for Semtech SX9500 SAR proximity chip */
|
|
|
|
/*
|
|
* Copyright (c) 2016 Intel Corporation
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#define DT_DRV_COMPAT semtech_sx9500
|
|
|
|
#include <errno.h>
|
|
|
|
#include <zephyr/kernel.h>
|
|
#include <zephyr/drivers/i2c.h>
|
|
#include <zephyr/drivers/sensor.h>
|
|
#include <zephyr/init.h>
|
|
#include <zephyr/drivers/gpio.h>
|
|
#include <zephyr/sys/__assert.h>
|
|
#include <zephyr/logging/log.h>
|
|
|
|
#include "sx9500.h"
|
|
|
|
LOG_MODULE_REGISTER(SX9500, CONFIG_SENSOR_LOG_LEVEL);
|
|
|
|
static uint8_t sx9500_reg_defaults[] = {
|
|
/*
|
|
* First number is register address to write to. The chip
|
|
* auto-increments the address for subsequent values in a single
|
|
* write message.
|
|
*/
|
|
SX9500_REG_PROX_CTRL1,
|
|
|
|
0x43, /* Shield enabled, small range. */
|
|
0x77, /* x8 gain, 167kHz frequency, finest resolution. */
|
|
0x40, /* Doze enabled, 2x scan period doze, no raw filter. */
|
|
0x30, /* Average threshold. */
|
|
0x0f, /* Debouncer off, lowest average negative filter,
|
|
* highest average positive filter.
|
|
*/
|
|
0x0e, /* Proximity detection threshold: 280 */
|
|
0x00, /* No automatic compensation, compensate each pin
|
|
* independently, proximity hysteresis: 32, close
|
|
* debouncer off, far debouncer off.
|
|
*/
|
|
0x00, /* No stuck timeout, no periodic compensation. */
|
|
};
|
|
|
|
static int sx9500_sample_fetch(const struct device *dev,
|
|
enum sensor_channel chan)
|
|
{
|
|
struct sx9500_data *data = dev->data;
|
|
const struct sx9500_config *cfg = dev->config;
|
|
|
|
__ASSERT_NO_MSG(chan == SENSOR_CHAN_ALL || chan == SENSOR_CHAN_PROX);
|
|
|
|
return i2c_reg_read_byte_dt(&cfg->i2c, SX9500_REG_STAT, &data->prox_stat);
|
|
}
|
|
|
|
static int sx9500_channel_get(const struct device *dev,
|
|
enum sensor_channel chan,
|
|
struct sensor_value *val)
|
|
{
|
|
struct sx9500_data *data = (struct sx9500_data *) dev->data;
|
|
|
|
__ASSERT_NO_MSG(chan == SENSOR_CHAN_PROX);
|
|
|
|
val->val1 = !!(data->prox_stat &
|
|
(1 << (4 + CONFIG_SX9500_PROX_CHANNEL)));
|
|
val->val2 = 0;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct sensor_driver_api sx9500_api_funcs = {
|
|
.sample_fetch = sx9500_sample_fetch,
|
|
.channel_get = sx9500_channel_get,
|
|
#ifdef CONFIG_SX9500_TRIGGER
|
|
.trigger_set = sx9500_trigger_set,
|
|
#endif
|
|
};
|
|
|
|
static int sx9500_init_chip(const struct device *dev)
|
|
{
|
|
const struct sx9500_config *cfg = dev->config;
|
|
uint8_t val;
|
|
|
|
if (i2c_write_dt(&cfg->i2c, sx9500_reg_defaults,
|
|
sizeof(sx9500_reg_defaults))
|
|
< 0) {
|
|
return -EIO;
|
|
}
|
|
|
|
/* No interrupts active. We only activate them when an
|
|
* application registers a trigger.
|
|
*/
|
|
if (i2c_reg_write_byte_dt(&cfg->i2c, SX9500_REG_IRQ_MSK, 0) < 0) {
|
|
return -EIO;
|
|
}
|
|
|
|
/* Read irq source reg to clear reset status. */
|
|
if (i2c_reg_read_byte_dt(&cfg->i2c, SX9500_REG_IRQ_SRC, &val) < 0) {
|
|
return -EIO;
|
|
}
|
|
|
|
return i2c_reg_write_byte_dt(&cfg->i2c, SX9500_REG_PROX_CTRL0,
|
|
1 << CONFIG_SX9500_PROX_CHANNEL);
|
|
}
|
|
|
|
int sx9500_init(const struct device *dev)
|
|
{
|
|
const struct sx9500_config *cfg = dev->config;
|
|
|
|
if (!device_is_ready(cfg->i2c.bus)) {
|
|
LOG_ERR("Bus device is not ready");
|
|
return -ENODEV;
|
|
}
|
|
|
|
if (sx9500_init_chip(dev) < 0) {
|
|
LOG_DBG("sx9500: failed to initialize chip");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (cfg->int_gpio.port) {
|
|
if (sx9500_setup_interrupt(dev) < 0) {
|
|
LOG_DBG("sx9500: failed to setup interrupt");
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define SX9500_DEFINE(inst) \
|
|
struct sx9500_data sx9500_data_##inst; \
|
|
\
|
|
static const struct sx9500_config sx9500_config_##inst = { \
|
|
.i2c = I2C_DT_SPEC_INST_GET(inst), \
|
|
IF_ENABLED(CONFIG_SX9500_TRIGGER, \
|
|
(.int_gpio = GPIO_DT_SPEC_INST_GET_OR(inst, int_gpios, { 0 }),)) \
|
|
}; \
|
|
\
|
|
SENSOR_DEVICE_DT_INST_DEFINE(inst, sx9500_init, NULL, \
|
|
&sx9500_data_##inst, &sx9500_config_##inst, POST_KERNEL, \
|
|
CONFIG_SENSOR_INIT_PRIORITY, &sx9500_api_funcs); \
|
|
|
|
DT_INST_FOREACH_STATUS_OKAY(SX9500_DEFINE)
|