257 lines
6.9 KiB
ReStructuredText
257 lines
6.9 KiB
ReStructuredText
.. _up_squared:
|
|
|
|
UP Squared
|
|
##########
|
|
|
|
Overview
|
|
********
|
|
|
|
UP |sup2| (UP Squared) is an ultra compact single board computer with high
|
|
performance and low power consumption. It features the latest Intel |reg| Apollo
|
|
Lake Celeron |trade| and Pentium |trade| Processors with only 4W of Scenario Design Power and
|
|
a powerful and flexible Intel |reg| FPGA Altera MAX 10 onboard.
|
|
|
|
.. figure:: img/up_squared.png
|
|
:width: 800px
|
|
:align: center
|
|
:alt: UP Squared
|
|
|
|
Up Squared (Credit: https://up-board.org)
|
|
|
|
This board configuration enables kernel support for the `UP Squared`_ board.
|
|
|
|
.. note::
|
|
This board configuration works on all three variants of `UP Squared`_
|
|
boards containing Intel |reg| Pentium |trade| SoC,
|
|
Intel |reg| Celeron |trade| SoC, or Intel |reg| Atom |trade| SoC.
|
|
|
|
Hardware
|
|
********
|
|
|
|
General information about the board can be found at the `UP Squared`_ website.
|
|
|
|
.. include:: ../../../../soc/x86/apollo_lake/doc/supported_features.txt
|
|
|
|
GPIO
|
|
----
|
|
|
|
GPIOs are exposed through the HAT header, and can be referred using
|
|
predefined macros such as ``UP2_HAT_PIN3``. The physical pins are
|
|
connected to the on-board FPGA acting as level shifter. Therefore,
|
|
to actually utilize these GPIO pins, the function of the pins and
|
|
directions (input/output) must be set in the BIOS. This can be
|
|
accomplished in BIOS, under menu ``Advanced``, and option
|
|
``HAT Configurations``. When a corresponding pin is set to act as
|
|
GPIO, there is an option to set the direction of the pin. This needs
|
|
to be set accordingly for the GPIO to function properly.
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
Refer to the `UP Squared`_ website and `UP Squared Pinout`_ website
|
|
for connection diagrams.
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Use the following procedures for booting an image on a UP Squared board.
|
|
|
|
.. contents::
|
|
:depth: 1
|
|
:local:
|
|
:backlinks: top
|
|
|
|
Build Zephyr application
|
|
========================
|
|
|
|
#. Build a Zephyr application; for instance, to build the ``hello_world``
|
|
application on UP Squared:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: up_squared
|
|
:goals: build
|
|
|
|
.. note::
|
|
|
|
A Zephyr EFI image file named :file:`zephyr.efi` is automatically
|
|
created in the build directory after the application is built.
|
|
|
|
Preparing the Boot Device
|
|
=========================
|
|
|
|
Prepare a USB flash drive to boot the Zephyr application image on
|
|
a UP Squared board.
|
|
|
|
#. Refer to the `UP Squared Serial Console Wiki page
|
|
<https://wiki.up-community.org/Serial_console>`_ for instructions on how to
|
|
connect for serial console.
|
|
|
|
#. Format the USB flash drive as FAT32.
|
|
|
|
On Windows, open ``File Explorer``, and right-click on the USB flash drive.
|
|
Select ``Format...``. Make sure in ``File System``, ``FAT32`` is selected.
|
|
Click on the ``Format`` button and wait for it to finish.
|
|
|
|
On Linux, graphical utilities such as ``gparted`` can be used to format
|
|
the USB flash drive as FAT32. Alternatively, under terminal, find out
|
|
the corresponding device node for the USB flash drive (for example,
|
|
``/dev/sdd``). Execute the following command:
|
|
|
|
.. code-block:: console
|
|
|
|
$ mkfs.vfat -F 32 <device-node>
|
|
|
|
.. important::
|
|
Make sure the device node is the actual device node for
|
|
the USB flash drive. Or else you may erase other storage devices
|
|
on your system, and will render the system unusable afterwards.
|
|
|
|
#. Copy the Zephyr EFI image file :file:`zephyr/zephyr.efi` to the USB drive.
|
|
|
|
Booting the UP Squared Board
|
|
============================
|
|
|
|
Boot the UP Squared board to the EFI shell with USB flash drive connected.
|
|
|
|
#. Insert the prepared boot device (USB flash drive) into the UP Squared board.
|
|
|
|
#. Connect the board to the host system using the serial cable and
|
|
configure your host system to watch for serial data. See
|
|
https://wiki.up-community.org/Serial_console.
|
|
|
|
.. note::
|
|
On Windows, PuTTY has an option to set up configuration for
|
|
serial data. Use a baud rate of 115200.
|
|
|
|
#. Power on the UP Squared board.
|
|
|
|
#. When the following output appears, press :kbd:`F7`:
|
|
|
|
.. code-block:: console
|
|
|
|
Press <DEL> or <ESC> to enter setup.
|
|
|
|
#. From the menu that appears, select the menu entry that describes
|
|
that particular EFI shell.
|
|
|
|
#. From the EFI shell select Zephyr EFI image to boot.
|
|
|
|
.. code-block:: console
|
|
|
|
Shell> fs0:zephyr.efi
|
|
|
|
.. note::
|
|
You can safely ignore this message if it appears:
|
|
|
|
.. code-block:: console
|
|
|
|
WARNING: no console will be available to OS
|
|
|
|
|
|
Booting the UP Squared Board over network
|
|
=========================================
|
|
|
|
Build Zephyr image
|
|
------------------
|
|
|
|
#. Follow `Build Zephyr application`_ steps to build Zephyr image.
|
|
|
|
Prepare Linux host
|
|
------------------
|
|
|
|
#. Install DHCP, TFTP servers. For example ``dnsmasq``
|
|
|
|
.. code-block:: console
|
|
|
|
$ sudo apt-get install dnsmasq
|
|
|
|
#. Configure DHCP server. Configuration for ``dnsmasq`` is below:
|
|
|
|
.. code-block:: console
|
|
|
|
# Only listen to this interface
|
|
interface=eno2
|
|
dhcp-range=10.1.1.20,10.1.1.30,12h
|
|
|
|
#. Configure TFTP server.
|
|
|
|
.. code-block:: console
|
|
|
|
# tftp
|
|
enable-tftp
|
|
tftp-root=/srv/tftp
|
|
dhcp-boot=zephyr.efi
|
|
|
|
``zephyr.efi`` is a Zephyr EFI binary created above.
|
|
|
|
#. Copy the Zephyr EFI image :file:`zephyr/zephyr.efi` to the
|
|
:file:`/srv/tftp` folder.
|
|
|
|
.. code-block:: console
|
|
|
|
$ sudo cp zephyr/zephyr.efi /srv/tftp
|
|
|
|
|
|
#. TFTP root should be looking like:
|
|
|
|
.. code-block:: console
|
|
|
|
$ tree /srv/tftp
|
|
/srv/tftp
|
|
└── zephyr.efi
|
|
|
|
#. Restart ``dnsmasq`` service:
|
|
|
|
.. code-block:: console
|
|
|
|
$ sudo systemctl restart dnsmasq.service
|
|
|
|
Prepare UP Squared board for network boot
|
|
-----------------------------------------
|
|
|
|
#. Enable PXE network from BIOS settings.
|
|
|
|
.. code-block:: console
|
|
|
|
Advanced -> Network Stack Configuration -> Enable Network Stack -> Enable Ipv4 PXE Support
|
|
|
|
#. Make network boot as the first boot option.
|
|
|
|
.. code-block:: console
|
|
|
|
Boot -> Boot Option #1 : [Network]
|
|
|
|
Booting UP Squared
|
|
------------------
|
|
|
|
#. Connect the board to the host system using the serial cable and
|
|
configure your host system to watch for serial data. See
|
|
https://wiki.up-community.org/Serial_console.
|
|
|
|
#. Power on the UP Squared board.
|
|
|
|
#. Verify that the board got an IP address:
|
|
|
|
.. code-block:: console
|
|
|
|
$ journalctl -f -u dnsmasq
|
|
dnsmasq-dhcp[5386]: DHCPDISCOVER(eno2) 00:07:32:52:25:88
|
|
dnsmasq-dhcp[5386]: DHCPOFFER(eno2) 10.1.1.28 00:07:32:52:25:88
|
|
dnsmasq-dhcp[5386]: DHCPREQUEST(eno2) 10.1.1.28 00:07:32:52:25:88
|
|
dnsmasq-dhcp[5386]: DHCPACK(eno2) 10.1.1.28 00:07:32:52:25:88
|
|
|
|
#. Verify that network booting is started:
|
|
|
|
.. code-block:: console
|
|
|
|
$ journalctl -f -u dnsmasq
|
|
dnsmasq-tftp[5386]: sent /srv/tftp/zephyr.efi to 10.1.1.28
|
|
|
|
#. When the boot process completes, you have finished booting the
|
|
Zephyr application image.
|
|
|
|
.. _UP Squared: https://www.up-board.org/upsquared/specifications
|
|
|
|
.. _UP Squared Pinout: https://wiki.up-community.org/Pinout
|