218 lines
6.3 KiB
ReStructuredText
218 lines
6.3 KiB
ReStructuredText
.. _black_f407zg_pro_board:
|
|
|
|
Black STM32 F407ZG Pro Development Board
|
|
########################################
|
|
|
|
Overview
|
|
********
|
|
|
|
The BLACK_F407ZG_PRO board features an ARM Cortex-M4 based STM32F407zg MCU
|
|
with a wide range of connectivity support and configurations. There are
|
|
multiple version of this board like ``black_f407ve``.
|
|
Here are some highlights of the BLACK_F407ZG_PRO board:
|
|
|
|
- STM32 microcontroller in LQFP144 package
|
|
- Extension header for all LQFP144 I/Os for quick connection to prototyping
|
|
board and easy probing
|
|
- Flexible board power supply:
|
|
|
|
- USB VBUS or external source (3.3V, 5V)
|
|
- Power management access point
|
|
|
|
- Three LEDs:
|
|
|
|
- 3.3 V power on (LD0)
|
|
- Two user LEDs: green (LD1), green (LD2)
|
|
|
|
- Four push-buttons: RESET, K0, K1 and WK_UP
|
|
- Mini-AB connector
|
|
|
|
.. image:: img/black_f407zg_pro.jpg
|
|
:align: center
|
|
:alt: BLACK_F407ZG_PRO
|
|
|
|
.. warning:: The +5V pins on this board are directly connected to the +5V pin
|
|
of the USB connector. There is no protection in place. Do not
|
|
power this board through USB and an external power supply at
|
|
the same time.
|
|
|
|
|
|
Hardware
|
|
********
|
|
|
|
BLACK_F407ZG_PRO board provides the following hardware components:
|
|
|
|
- STM32F407ZGT6 in LQFP144 package
|
|
- ARM |reg| 32-bit Cortex |reg| -M4 CPU with FPU
|
|
- 168 MHz max CPU frequency
|
|
- VDD from 1.8 V to 3.6 V
|
|
- 8MHz system crystal
|
|
- 32.768KHz RTC crystal
|
|
- JTAG/SWD header
|
|
- 1024 kB Flash
|
|
- 192+4 KB SRAM including 64-Kbyte of core coupled memory
|
|
- GPIO with external interrupt capability
|
|
- 3x12-bit ADC with 24 channels
|
|
- 2x12-bit D/A converters
|
|
- RTC battery CR1220
|
|
- Advanced-control Timer (2)
|
|
- General Purpose Timers (12)
|
|
- Watchdog Timers (2)
|
|
- USART (3), UART (2)
|
|
- I2C (3)
|
|
- I2S (2)
|
|
- SPI (3)
|
|
- SDIO (1)
|
|
- CAN (2)
|
|
- USB 2.0 OTG FS with on-chip PHY
|
|
- USB 2.0 OTG HS/FS with dedicated DMA, on-chip full-speed PHY and ULPI
|
|
- 10/100 Ethernet MAC with dedicated DMA
|
|
- CRC calculation unit
|
|
- True random number generator
|
|
- DMA Controller
|
|
- Micro SD
|
|
- 1x 10/100 Ethernet MAC
|
|
- 1x 8 to 12-bit Parallel Camera interface
|
|
- Micro USB for power and comms
|
|
- 2x jumpers for bootloader selection
|
|
- 2x16 FMSC LCD Interface
|
|
- NRF24L01 socket
|
|
- Dimensions: 102.5mm x 74.56mm
|
|
|
|
More information about STM32F407ZG SOC can be found here:
|
|
- `STM32F407ZG on www.st.com`_
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The Zephyr black_f407zg_pro board configuration supports the following hardware
|
|
features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+-------------------------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+-------------------------------------+
|
|
| PWM | on-chip | pwm |
|
|
+-----------+------------+-------------------------------------+
|
|
| USB | on-chip | usb |
|
|
+-----------+------------+-------------------------------------+
|
|
| CAN | on-chip | CAN controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| SPI | on-chip | spi |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
.. note:: CAN feature requires CAN transceiver.
|
|
Zephyr default configuration uses CAN_2 exclusively, as
|
|
simultaneous use of CAN_1 and CAN_2 is not yet supported.
|
|
|
|
Other hardware features are not yet supported on Zephyr porting.
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
|
|
``boards/arm/black_f407_generic/black_f407zg_pro_defconfig``
|
|
|
|
|
|
Pin Mapping
|
|
===========
|
|
|
|
BLACK_F407ZG_PRO has 7 GPIO controllers. These controllers are responsible for pin
|
|
muxing, input/output, pull-up, etc.
|
|
|
|
|
|
Default Zephyr Peripheral Mapping:
|
|
----------------------------------
|
|
|
|
.. rst-class:: rst-columns
|
|
|
|
- UART_1_TX : PB6
|
|
- UART_1_RX : PB7
|
|
- UART_2_TX : PA2
|
|
- UART_2_RX : PA3
|
|
- USER_PB : PA0
|
|
- LD3 : PD13
|
|
- LD4 : PD12
|
|
- LD5 : PD14
|
|
- LD6 : PD15
|
|
- USB DM : PA11
|
|
- USB DP : PA12
|
|
- CAN1_RX : PD0
|
|
- CAN1_TX : PD1
|
|
- CAN2_RX : PB12
|
|
- CAN2_TX : PB13
|
|
- SPI2 MISO : PC2
|
|
- SPI2 MOSI : PC3
|
|
- SPI2 SCK : PB10
|
|
|
|
System Clock
|
|
============
|
|
|
|
BLACK_F407ZG_PRO System Clock could be driven by internal or external oscillator,
|
|
as well as main PLL clock. By default System clock is driven by PLL clock
|
|
at 168MHz, driven by 8MHz high speed external clock.
|
|
|
|
Serial Port
|
|
===========
|
|
|
|
BLACK_F407ZG_PRO has up to 6 UARTs. The Zephyr console output is assigned to UART2.
|
|
Default settings are 115200 8N1.
|
|
Please note that ST-Link Virtual Com Port is not wired to chip serial port.
|
|
In order to enable console output you should use a serial cable and connect
|
|
it to UART2 pins (PA2/PA3).
|
|
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Applications for the ``black_f407zg_pro`` board configuration can be built and
|
|
flashed in the usual way (see :ref:`build_an_application` and
|
|
:ref:`application_run` for more details).
|
|
|
|
Flashing
|
|
========
|
|
|
|
BLACK_F407ZG_PRO board includes an ST-LINK/V2 embedded debug tool interface.
|
|
This interface is supported by the openocd version included in Zephyr SDK.
|
|
|
|
Flashing an application to BLACK_F407ZG_PRO
|
|
-------------------------------------------
|
|
|
|
Here is an example for the :ref:`blinky-sample` application.
|
|
|
|
Run a serial host program to connect with your board:
|
|
|
|
.. code-block:: console
|
|
|
|
$ minicom -D /dev/ttyACM0
|
|
|
|
Build and flash the application:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/basic/blinky
|
|
:board: black_f407zg_pro
|
|
:goals: build flash
|
|
|
|
You should see user led "LD1" blinking.
|
|
|
|
Debugging
|
|
=========
|
|
|
|
You can debug an application in the usual way. Here is an example for the
|
|
:ref:`hello_world` application.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: black_f407zg_pro
|
|
:maybe-skip-config:
|
|
:goals: debug
|
|
|
|
.. _STM32F407ZG on www.st.com:
|
|
https://www.st.com/en/microcontrollers-microprocessors/stm32f407zg.html
|