Michael Hope 247782a7b3 sam0: move the UART and SPI configuration into pinmux. ... Also pull out the SERCOM pads configuration to defines. Note that the SAM0 has a two level configuration - a signal (like TX) is mapped to a pad, and then a pad is mapped to a function on a pin. Signed-off-by: Michael Hope <mlhx@google.com>		2018-02-08 12:09:46 -06:00
..
adc	drivers: ti_adc108s102: remove newline from syslog messages	2018-01-09 10:59:41 -05:00
aio	kbuild: Removed KBuild	2017-11-08 20:00:22 -05:00
bluetooth	dts: add spi device support for SPI bluetooth modules	2018-01-22 18:08:51 -06:00
clock_control	clock_control: nrf5: Return -EBUSY on turning off if still in use	2018-02-08 14:51:31 +01:00
console	doc: fix misspellings in Kconfig files	2018-02-07 14:51:46 -05:00
counter	kbuild: Removed KBuild	2017-11-08 20:00:22 -05:00
crypto	kconfig: fix help syntax and add spaces	2017-12-13 17:43:28 -06:00
display	kbuild: Removed KBuild	2017-11-08 20:00:22 -05:00
dma	kconfig: fix help syntax and add spaces	2017-12-13 17:43:28 -06:00
entropy	drivers: entropy: stm32: use Kconfig to select HAL/LL sources	2018-01-23 08:46:16 -06:00
ethernet	drivers: ethernet: eth_stm32_hal: use Kconfig to select HAL/LL sources	2018-01-23 08:46:16 -06:00
flash	flash: mcux: implement software write protection (HACK)	2018-02-06 15:39:45 -06:00
gpio	lpc: Add gpio mcux driver for lpc	2018-01-23 09:18:32 -06:00
grove	kconfig: fix help syntax and add spaces	2017-12-13 17:43:28 -06:00
i2c	drivers: i2c: Add i2c master driver for Nios-II i2c core	2018-02-07 19:37:35 -05:00
i2s	drivers: Add Atmel SAM I2S (SSC) driver	2017-11-30 10:30:33 -05:00
ieee802154	drivers: cc2520: Change debug information	2018-02-02 16:50:07 +02:00
interrupt_controller	drivers/interrupt_controller: Introduce multi-level interrupt support	2018-02-06 22:39:05 -05:00
ipm	kconfig: fix help syntax and add spaces	2017-12-13 17:43:28 -06:00
led_strip	kbuild: Removed KBuild	2017-11-08 20:00:22 -05:00
net	drivers: net: loopback: Simulate real hw device	2017-11-15 12:27:14 +02:00
pci	drivers: pci: when enumerating, only print the device info	2018-02-01 02:19:45 -05:00
pinmux	drivers: pinmux: esp32: Fix using gpio as IO at the same time.	2018-02-07 14:52:25 -05:00
pwm	pwm: nrf5_sw: Fix configuration for nRF51	2018-02-08 11:21:51 +02:00
rtc	kconfig: fix help syntax and add spaces	2017-12-13 17:43:28 -06:00
sensor	sensors: move lps25hb and lsm6ds0 to dts	2018-02-07 10:30:36 -06:00
serial	sam0: move the UART and SPI configuration into pinmux.	2018-02-08 12:09:46 -06:00
spi	sam0: move the UART and SPI configuration into pinmux.	2018-02-08 12:09:46 -06:00
timer	native: native_posix timer + irq fix	2018-02-07 16:28:16 -05:00
usb	driver: usb_dw: Move base address and irq num of usb to soc.h	2018-02-07 22:55:11 -05:00
watchdog	watchdog: add a watchdog driver for the SAM0 family.	2018-01-04 13:18:25 -05:00
CMakeLists.txt	irq: move shared irq support under drivers/interrupt_controller	2018-01-23 13:37:01 -06:00
Kconfig	irq: move shared irq support under drivers/interrupt_controller	2018-01-23 13:37:01 -06:00