163 lines
4.8 KiB
ReStructuredText
163 lines
4.8 KiB
ReStructuredText
.. _nucleo_f303re_board:
|
|
|
|
ST Nucleo F303RE
|
|
################
|
|
|
|
Overview
|
|
********
|
|
|
|
The Nucleo F303RE board features an ARM Cortex-M4 based STM32F303RE
|
|
mixed-signal MCU with FPU and DSP instructions capable of running at 72 MHz.
|
|
Here are some highlights of the Nucleo F303RE board:
|
|
|
|
- STM32 microcontroller in LQFP64 package
|
|
- LSE crystal: 32.768 kHz crystal oscillator
|
|
- Two types of extension resources:
|
|
|
|
- Arduino* Uno V3 connectors
|
|
- ST morpho extension pin headers for full access to all STM32 I/Os
|
|
|
|
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
|
|
- Flexible board power supply:
|
|
|
|
- 5 V from ST-LINK/V2-1 USB VBUS
|
|
- External power sources: 3.3 V and 7 - 12 V on ST Zio or ST morpho
|
|
connectors, 5 V on ST morpho connector
|
|
|
|
- One user LED
|
|
- Two push-buttons: USER and RESET
|
|
|
|
.. image:: img/nucleo_f303re.jpg
|
|
:width: 500px
|
|
:height: 367px
|
|
:align: center
|
|
:alt: Nucleo F303RE
|
|
|
|
More information about the board can be found at the `Nucleo F303RE website`_,
|
|
and in the `STM32 Nucleo-64 board User Manual`_.
|
|
|
|
Hardware
|
|
********
|
|
|
|
The Nucleo F303RE provides the following hardware components:
|
|
|
|
- STM32F303RET6 in QFP64 package
|
|
- ARM |reg| 32-bit Cortex |reg| -M4 CPU with FPU
|
|
- 72 MHz max CPU frequency
|
|
- VDD from 2.0 V to 3.6 V
|
|
- 512 MB Flash
|
|
- 64 + 16 KB SRAM
|
|
- RTC
|
|
- Advanced-control Timer
|
|
- General Purpose Timers (4)
|
|
- Basic Timer
|
|
- Watchdog Timers (2)
|
|
- PWM channels (18)
|
|
- SPI/I2S (2)
|
|
- I2C (3)
|
|
- USART/UART (3/3)
|
|
- USB 2.0 FS with on-chip PHY
|
|
- CAN (2)
|
|
- GPIO with external interrupt capability
|
|
- DMA channels (12)
|
|
- Capacitive sensing channels (18)
|
|
- 12-bit ADC with 40 channels (4)
|
|
- 12-bit D/A converter with two channels
|
|
- Analog comparator (7)
|
|
- Op amp (4)
|
|
- Capacitive sensing 24 channels
|
|
|
|
|
|
More information about the STM32F303RE can be found here:
|
|
|
|
- `STM32F303RE on www.st.com`_
|
|
- `STM32F303RE reference manual`_
|
|
- `STM32F303RE datasheet`_
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The Zephyr nucleo_f302r8 board configuration supports the following hardware
|
|
features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+-------------------------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+-------------------------------------+
|
|
| RTC | on-chip | rtc |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
Other hardware features are not yet supported on this Zephyr port.
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
``boards/arm/nucleo_f303re/nucleo_f303re_defconfig``
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
The Nucleo F303RE Board has 5 GPIO controllers. These controllers are
|
|
responsible for pin muxing, input/output, pull-up, etc.
|
|
|
|
Board connectors:
|
|
-----------------
|
|
.. image:: img/nucleo_connectors.png
|
|
:width: 800px
|
|
:align: center
|
|
:height: 619px
|
|
:alt: Nucleo F303RE connectors
|
|
|
|
Default Zephyr Peripheral Mapping:
|
|
----------------------------------
|
|
|
|
The Nucleo F303RE board features an Arduino Uno V3 connector and a ST
|
|
morpho connector. Board is configured as follows:
|
|
|
|
- UART_2 TX/RX : PA2/PA3 (ST-Link Virtual Port Com)
|
|
- USER_PB : PC13
|
|
- LD2 : PA5
|
|
|
|
System Clock
|
|
------------
|
|
|
|
The Nucleo F303RE System Clock can be driven by an internal or
|
|
external oscillator, as well as by the main PLL clock. By default the
|
|
System Clock is driven by the PLL clock at 72 MHz. The input to the
|
|
PLL is an 8 MHz external clock supplied by the processor of the
|
|
on-board ST-LINK/V2-1 debugger/programmer.
|
|
|
|
Serial Port
|
|
-----------
|
|
|
|
The Nucleo F303RE board has 2 UARTs. The Zephyr console output is assigned
|
|
to UART2. Default settings are 115200 8N1.
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
The Nucleo F303RE board includes an ST-LINK/V2-1 embedded debug tool interface.
|
|
This interface is supported by the openocd version included in Zephyr SDK.
|
|
|
|
|
|
.. _Nucleo F303RE website:
|
|
http://www.st.com/en/evaluation-tools/nucleo-f303re.html
|
|
|
|
.. _STM32 Nucleo-64 board User Manual:
|
|
http://www.st.com/resource/en/user_manual/dm00105823.pdf
|
|
|
|
.. _STM32F303RE on www.st.com:
|
|
http://www.st.com/en/microcontrollers/stm32f303re.html
|
|
|
|
.. _STM32F303RE reference manual:
|
|
https://www.st.com/resource/en/reference_manual/dm00043574.pdf
|
|
|
|
.. _STM32F303RE datasheet:
|
|
http://www.st.com/resource/en/datasheet/stm32f303re.pdf
|