137 lines
3.2 KiB
Plaintext
137 lines
3.2 KiB
Plaintext
# Kconfig - MPU6050 Six-Axis Motion Tracking device configuration options
|
|
|
|
#
|
|
# Copyright (c) 2016 Intel Corporation
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
menuconfig MPU6050
|
|
bool
|
|
prompt "MPU6050 Six-Axis Motion Tracking Device"
|
|
depends on SENSOR && I2C
|
|
default n
|
|
help
|
|
Enable driver for MPU6050 I2C-based six-axis motion tracking device.
|
|
|
|
config MPU6050_NAME
|
|
string
|
|
prompt "Driver name"
|
|
default "MPU6050"
|
|
depends on MPU6050
|
|
help
|
|
Device name with which the MPU6050 sensor is identified.
|
|
|
|
config MPU6050_I2C_ADDR
|
|
hex
|
|
prompt "I2C address"
|
|
depends on MPU6050
|
|
default 0x68
|
|
range 0x68 0x69
|
|
help
|
|
I2C address of the MPU6050 sensor.
|
|
Choose 0x68 if the AD0 pin is pulled to GND or 0x69 if the AD0 pin
|
|
is pulled to VDD.
|
|
|
|
config MPU6050_I2C_MASTER_DEV_NAME
|
|
string
|
|
prompt "I2C master where MPU6050 is connected"
|
|
depends on MPU6050
|
|
default "I2C_0"
|
|
help
|
|
Specify the device name of the I2C master device to which MPU6050 is
|
|
connected.
|
|
|
|
choice
|
|
prompt "Trigger mode"
|
|
depends on MPU6050
|
|
default MPU6050_TRIGGER_GLOBAL_THREAD
|
|
help
|
|
Specify the type of triggering to be used by the driver.
|
|
|
|
config MPU6050_TRIGGER_NONE
|
|
bool
|
|
prompt "No trigger"
|
|
|
|
config MPU6050_TRIGGER_GLOBAL_THREAD
|
|
bool
|
|
prompt "Use global thread"
|
|
depends on GPIO
|
|
select MPU6050_TRIGGER
|
|
|
|
config MPU6050_TRIGGER_OWN_THREAD
|
|
bool
|
|
prompt "Use own thread"
|
|
depends on GPIO
|
|
select MPU6050_TRIGGER
|
|
|
|
endchoice
|
|
|
|
config MPU6050_TRIGGER
|
|
bool
|
|
depends on MPU6050
|
|
|
|
config MPU6050_GPIO_DEV_NAME
|
|
string
|
|
prompt "GPIO device"
|
|
default "GPIO_0"
|
|
depends on MPU6050 && MPU6050_TRIGGER
|
|
help
|
|
The device name of the GPIO device to which the MPU6050 interrupt pin
|
|
is connected.
|
|
|
|
config MPU6050_GPIO_PIN_NUM
|
|
int
|
|
prompt "Interrupt GPIO pin number"
|
|
default 0
|
|
depends on MPU6050 && MPU6050_TRIGGER
|
|
help
|
|
The number of the GPIO on which the interrupt signal from the MPU6050
|
|
chip will be received.
|
|
|
|
config MPU6050_THREAD_PRIORITY
|
|
int
|
|
prompt "Thread priority"
|
|
depends on MPU6050 && MPU6050_TRIGGER_OWN_THREAD
|
|
default 10
|
|
help
|
|
Priority of thread used by the driver to handle interrupts.
|
|
|
|
config MPU6050_THREAD_STACK_SIZE
|
|
int
|
|
prompt "Thread stack size"
|
|
depends on MPU6050 && MPU6050_TRIGGER_OWN_THREAD
|
|
default 1024
|
|
help
|
|
Stack size of thread used by the driver to handle interrupts.
|
|
|
|
config MPU6050_ACCEL_FS
|
|
int
|
|
prompt "Accelerometer full-scale range"
|
|
depends on MPU6050
|
|
default 2
|
|
help
|
|
Magnetometer full-scale range.
|
|
An X value for the config represents a range of +/- X g. Valid
|
|
values are 2, 4, 8 and 16.
|
|
|
|
config MPU6050_GYRO_FS
|
|
int
|
|
prompt "Gyroscope full-scale range"
|
|
depends on MPU6050
|
|
default 250
|
|
help
|
|
Gyroscope full-scale range.
|
|
An X value for the config represents a range of +/- X degrees/second.
|
|
Valid values are 250, 500, 1000, 2000.
|