145 lines
3.3 KiB
Plaintext
145 lines
3.3 KiB
Plaintext
# Kconfig - LSM9DS0 gyroscope sensor configuration options
|
|
|
|
#
|
|
# Copyright (c) 2016 Intel Corporation
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
menuconfig LSM9DS0_GYRO
|
|
bool "LSM9DS0 I2C gyroscope Chip"
|
|
depends on SENSOR && I2C && NANO_TIMEOUTS
|
|
default n
|
|
help
|
|
Enable driver for LSM9DS0 I2C-based gyroscope sensor.
|
|
|
|
config LSM9DS0_GYRO_DEV_NAME
|
|
string "LSM9DS0_GYRO device name"
|
|
depends on LSM9DS0_GYRO
|
|
default "lsm9ds0_gyro"
|
|
|
|
config LSM9DS0_GYRO_I2C_ADDR
|
|
hex
|
|
prompt "LSM9DS0_GYRO I2C slave address"
|
|
default 0x6A
|
|
depends on LSM9DS0_GYRO
|
|
help
|
|
Specify the I2C slave address for the LSM9DS0_GYRO.
|
|
|
|
0x6A: GND
|
|
0x6B: VCC
|
|
|
|
config LSM9DS0_GYRO_I2C_MASTER_DEV_NAME
|
|
string "I2C master where LSM9DS0 gyroscope is connected"
|
|
depends on LSM9DS0_GYRO
|
|
default "I2C_0"
|
|
help
|
|
Specify the device name of the I2C master device to which LSM9DS0_GYRO
|
|
is connected.
|
|
|
|
menu "Attributes"
|
|
depends on LSM9DS0_GYRO
|
|
|
|
choice
|
|
prompt "Default full-scale"
|
|
default LSM9DS0_GYRO_FULLSCALE_245
|
|
depends on LSM9DS0_GYRO
|
|
help
|
|
Specify the default full-scale.
|
|
|
|
config LSM9DS0_GYRO_FULLSCALE_245
|
|
bool
|
|
prompt "245 DPS"
|
|
|
|
config LSM9DS0_GYRO_FULLSCALE_500
|
|
bool
|
|
prompt "500 DPS"
|
|
|
|
config LSM9DS0_GYRO_FULLSCALE_2000
|
|
bool
|
|
prompt "2000 DPS"
|
|
|
|
endchoice
|
|
|
|
config LSM9DS0_GYRO_FULLSCALE_RUNTIME
|
|
bool "Enable dynamic full-scale"
|
|
depends on LSM9DS0_GYRO
|
|
default n
|
|
help
|
|
Enable alteration of full-scale attribute at runtime.
|
|
|
|
choice
|
|
prompt "Default sampling rate frequency"
|
|
default LSM9DS0_GYRO_SAMPLING_RATE_95
|
|
depends on LSM9DS0_GYRO
|
|
help
|
|
Specify the default sampling rate frequency.
|
|
|
|
config LSM9DS0_GYRO_SAMPLING_RATE_95
|
|
bool
|
|
prompt "95 Hz"
|
|
|
|
config LSM9DS0_GYRO_SAMPLING_RATE_190
|
|
bool
|
|
prompt "190 Hz"
|
|
|
|
config LSM9DS0_GYRO_SAMPLING_RATE_380
|
|
bool
|
|
prompt "380 Hz"
|
|
|
|
config LSM9DS0_GYRO_SAMPLING_RATE_760
|
|
bool
|
|
prompt "760 Hz"
|
|
|
|
endchoice
|
|
|
|
config LSM9DS0_GYRO_SAMPLING_RATE_RUNTIME
|
|
bool "Enable dynamic sampling rate"
|
|
depends on LSM9DS0_GYRO
|
|
default n
|
|
help
|
|
Enable alteration of sampling rate frequency at runtime.
|
|
|
|
endmenu
|
|
|
|
config LSM9DS0_GYRO_TRIGGERS
|
|
bool "Enable triggers"
|
|
depends on LSM9DS0_GYRO && GPIO
|
|
default n
|
|
|
|
config LSM9DS0_GYRO_THREAD_STACK_SIZE
|
|
int "Thread stack size"
|
|
depends on LSM9DS0_GYRO_TRIGGERS
|
|
default 1024
|
|
help
|
|
Specify the internal thread stack size.
|
|
|
|
config LSM9DS0_GYRO_TRIGGER_DRDY
|
|
bool "Enable data ready trigger"
|
|
depends on LSM9DS0_GYRO_TRIGGERS
|
|
default n
|
|
|
|
config LSM9DS0_GYRO_GPIO_DRDY_DEV_NAME
|
|
string "GPIO device where LSM9DS0_GYRO data ready interrupt is connected"
|
|
depends on LSM9DS0_GYRO_TRIGGER_DRDY
|
|
default GPIO_0
|
|
help
|
|
Specify the device name of the GPIO controller the BMC150_MAGN interrupt
|
|
is connected to.
|
|
|
|
config LSM9DS0_GYRO_GPIO_DRDY_INT_PIN
|
|
int
|
|
default 3
|
|
depends on LSM9DS0_GYRO_TRIGGER_DRDY
|
|
prompt "GPIO pin number for the data ready interrupt pin"
|