242 lines
7.2 KiB
ReStructuredText
242 lines
7.2 KiB
ReStructuredText
.. _nucleo_l432kc_board:
|
|
|
|
ST Nucleo L432KC
|
|
################
|
|
|
|
Overview
|
|
********
|
|
|
|
The Nucleo L432KC board features an ARM Cortex-M4 based STM32L432KC MCU
|
|
with a wide range of connectivity support and configurations. Here are
|
|
some highlights of the Nucleo L432KC board:
|
|
|
|
- STM32 microcontroller in UFQFPN32 package
|
|
- Arduino Uno V3 connectivity
|
|
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
|
|
- Flexible board power supply:
|
|
|
|
- USB VBUS or external source(3.3V, 5V, 7 - 12V)
|
|
- Power management access point
|
|
|
|
- Three LEDs: USB communication (LD1), power LED (LD2), user LED (LD3)
|
|
- One push-button: RESET
|
|
|
|
.. image:: img/nucleo_l432kc.jpg
|
|
:align: center
|
|
:alt: Nucleo L432KC
|
|
|
|
More information about the board can be found at the `Nucleo L432KC website`_.
|
|
|
|
Hardware
|
|
********
|
|
|
|
The STM32L432KC SoC provides the following hardware IPs:
|
|
|
|
- Ultra-low-power with FlexPowerControl (down to 28 nA Standby mode and 84
|
|
|micro| A/MHz run mode)
|
|
- Core: ARM |reg| 32-bit Cortex |reg| -M4 CPU with FPU, frequency up to 80 MHz,
|
|
100DMIPS/1.25DMIPS/MHz (Dhrystone 2.1)
|
|
- Clock Sources:
|
|
|
|
- 32 kHz crystal oscillator for RTC (LSE)
|
|
- Internal 16 MHz factory-trimmed RC ( |plusminus| 1%)
|
|
- Internal low-power 32 kHz RC ( |plusminus| 5%)
|
|
- Internal multispeed 100 kHz to 48 MHz oscillator, auto-trimmed by
|
|
LSE (better than |plusminus| 0.25 % accuracy)
|
|
- 2 PLLs for system clock, USB, audio, ADC
|
|
|
|
- RTC with HW calendar, alarms and calibration
|
|
- Up to 3 capacitive sensing channels: support touchkey, linear and rotary touch sensors
|
|
- 11x timers:
|
|
|
|
- 1x 16-bit advanced motor-control
|
|
- 1x 32-bit and 2x 16-bit general purpose
|
|
- 2x 16-bit basic
|
|
- 2x low-power 16-bit timers (available in Stop mode)
|
|
- 2x watchdogs
|
|
- SysTick timer
|
|
|
|
- Up to 26 fast I/Os, most 5 V-tolerant
|
|
- Memories
|
|
|
|
- Up to 256 KB single bank Flash, proprietary code readout protection
|
|
- Up to 64 KB of SRAM including 16 KB with hardware parity check
|
|
- Quad SPI memory interface
|
|
|
|
- Rich analog peripherals (independent supply)
|
|
|
|
- 1x 12-bit ADC 5 MSPS, up to 16-bit with hardware oversampling, 200
|
|
|micro| A/MSPS
|
|
- 2x 12-bit DAC, low-power sample and hold
|
|
- 1x operational amplifiers with built-in PGA
|
|
- 2x ultra-low-power comparators
|
|
|
|
- 13x communication interfaces
|
|
|
|
- USB OTG 2.0 full-speed crystal less solution with LPM and BCD
|
|
- 1x SAIs (serial audio interface)
|
|
- 2x I2C FM+(1 Mbit/s), SMBus/PMBus
|
|
- 3x USARTs (ISO 7816, LIN, IrDA, modem)
|
|
- 2x SPIs (3x SPIs with the Quad SPI)
|
|
- CAN (2.0B Active)
|
|
- SWPMI single wire protocol master I/F
|
|
- IRTIM (Infrared interface)
|
|
|
|
- 14-channel DMA controller
|
|
- True random number generator
|
|
- CRC calculation unit, 96-bit unique ID
|
|
- Development support: serial wire debug (SWD), JTAG, Embedded Trace Macrocell*
|
|
|
|
|
|
More information about STM32L432KC can be found here:
|
|
|
|
- `STM32L432KC on www.st.com`_
|
|
- `STM32L432 reference manual`_
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The Zephyr nucleo_l432kc board configuration supports the following hardware features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+-------------------------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+-------------------------------------+
|
|
| I2C | on-chip | i2c |
|
|
+-----------+------------+-------------------------------------+
|
|
| PWM | on-chip | pwm |
|
|
+-----------+------------+-------------------------------------+
|
|
| CAN | on-chip | can |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
.. note:: CAN feature requires CAN transceiver
|
|
|
|
Other hardware features are not yet supported on this Zephyr port.
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
:zephyr_file:`boards/st/nucleo_l432kc/nucleo_l432kc_defconfig`
|
|
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
Nucleo L432KC Board has 6 GPIO controllers. These controllers are responsible for pin muxing,
|
|
input/output, pull-up, etc.
|
|
|
|
Available pins:
|
|
---------------
|
|
.. image:: img/nucleo_l432kc_arduino_nano.jpg
|
|
:align: center
|
|
:alt: Nucleo L432KC Arduino connectors
|
|
|
|
For more details please refer to `STM32 Nucleo-32 board User Manual`_.
|
|
|
|
Default Zephyr Peripheral Mapping:
|
|
----------------------------------
|
|
|
|
- UART_1_TX : PA9
|
|
- UART_1_RX : PA10
|
|
- UART_2_TX : PA2
|
|
- UART_2_RX : PA3
|
|
- I2C_1_SCL : PB6
|
|
- I2C_1_SDA : PB7
|
|
- PWM_2_CH1 : PA0
|
|
- LD3 : PB3
|
|
|
|
System Clock
|
|
------------
|
|
|
|
Nucleo L432KC System Clock could be driven by internal or external oscillator,
|
|
as well as main PLL clock. By default System clock is driven by PLL clock at 80MHz,
|
|
driven by 16MHz high speed internal oscillator.
|
|
|
|
Serial Port
|
|
-----------
|
|
|
|
Nucleo L432KC board has 3 U(S)ARTs. The Zephyr console output is assigned to UART2.
|
|
Default settings are 115200 8N1.
|
|
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Nucleo L432KC board includes an ST-LINK/V2-1 embedded debug tool interface.
|
|
|
|
Applications for the ``nucleo_l432kc`` board configuration can be built and
|
|
flashed in the usual way (see :ref:`build_an_application` and
|
|
:ref:`application_run` for more details).
|
|
|
|
Flashing
|
|
========
|
|
|
|
The board is configured to be flashed using west `STM32CubeProgrammer`_ runner,
|
|
so its :ref:`installation <stm32cubeprog-flash-host-tools>` is required.
|
|
|
|
Alternatively, OpenOCD or JLink can also be used to flash the board using
|
|
the ``--runner`` (or ``-r``) option:
|
|
|
|
.. code-block:: console
|
|
|
|
$ west flash --runner openocd
|
|
$ west flash --runner jlink
|
|
|
|
Flashing an application to Nucleo L432KC
|
|
----------------------------------------
|
|
|
|
Connect the Nucleo L432KC to your host computer using the USB port,
|
|
then run a serial host program to connect with your Nucleo board.
|
|
|
|
.. code-block:: console
|
|
|
|
$ minicom -D /dev/ttyACM0
|
|
|
|
Now build and flash an application. Here is an example for
|
|
:zephyr:code-sample:`hello_world`.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: nucleo_l432kc
|
|
:goals: build flash
|
|
|
|
You should see the following message on the console:
|
|
|
|
.. code-block:: console
|
|
|
|
$ Hello World! arm
|
|
|
|
|
|
Debugging
|
|
=========
|
|
|
|
You can debug an application in the usual way. Here is an example for the
|
|
:zephyr:code-sample:`hello_world` application.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: nucleo_l432kc
|
|
:maybe-skip-config:
|
|
:goals: debug
|
|
|
|
.. _Nucleo L432KC website:
|
|
https://www.st.com/en/evaluation-tools/nucleo-l432kc.html
|
|
|
|
.. _STM32 Nucleo-32 board User Manual:
|
|
https://www.st.com/resource/en/user_manual/dm00231744.pdf
|
|
|
|
.. _STM32L432KC on www.st.com:
|
|
https://www.st.com/en/microcontrollers/stm32l432kc.html
|
|
|
|
.. _STM32L432 reference manual:
|
|
https://www.st.com/resource/en/reference_manual/dm00151940.pdf
|
|
|
|
.. _STM32CubeProgrammer:
|
|
https://www.st.com/en/development-tools/stm32cubeprog.html
|