zephyr/tests/kernel/context
Andy Ross c2c6bee036 drivers/timer: Remove legacy APIC driver
For a while now, we've had two APIC drivers.  The older was preserved
initially as the new (much smaller, "new style") code didn't have
support for Quark interrupt handling.  But that's long dead now.  Just
remove it.

Note that this migrates the one board using this driver (acrn) to
CONFIG_APIC_TIMER instead.

Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
2020-12-27 18:19:17 +01:00
..
src drivers/timer: Remove legacy APIC driver 2020-12-27 18:19:17 +01:00
CMakeLists.txt
README.txt
prj.conf
testcase.yaml

README.txt

Title: Context and IRQ APIs

Description:

This test verifies that the kernel CPU and context APIs operate as expected.


APIs tested in this test set
============================

k_thread_create
  - start a helper thread to help with k_yield() tests
  - start a thread to test thread related functionality

k_yield
  - Called by a higher priority thread when there is another thread
  - Called by an equal priority thread when there is another thread
  - Called by a lower priority thread when there is another thread

k_current_get
  - Called from an ISR (interrupted a task)
  - Called from an ISR (interrupted a thread)
  - Called from a task
  - Called from a thread

k_is_in_isr
  - Called from an ISR that interrupted a task
  - Called from an ISR that interrupted a thread
  - Called from a task
  - Called from a thread

k_cpu_idle
  - Tickless Kernel: CPU to be woken up by a kernel timer (k_timer)
  - Non-tickless kernel:
    CPU to be woken up by tick timer.  Thus, after each call, the tick count
    should have advanced by one tick.

irq_lock
  - 1. Count the number of calls to _tick_get_32() before a tick expires.
  - 2. Once determined, call _tick_get_32() many more times than that
       with interrupts locked.  Check that the tick count remains unchanged.

irq_unlock
  - Continuation irq_lock: unlock interrupts, loop and verify the tick
    count changes.

irq_offload
  - Used when triggering an ISR to perform ISR context work.

irq_enable
irq_disable
  - Use these routines to disable and enable timer interrupts so that they can
    be tested in the same way as irq_lock() and irq_unlock().

---------------------------------------------------------------------------

Building and Running Project:

This project outputs to the console.  It can be built and executed
on QEMU as follows:

    make run

---------------------------------------------------------------------------

Troubleshooting:

Problems caused by out-dated project information can be addressed by
issuing one of the following commands then rebuilding the project:

    make clean          # discard results of previous builds
                        # but keep existing configuration info
or
    make pristine       # discard results of previous builds
                        # and restore pre-defined configuration info

---------------------------------------------------------------------------

Sample Output:

tc_start() - Test kernel CPU and thread routines
Initializing kernel objects
Testing k_cpu_idle()
Testing interrupt locking and unlocking
Testing irq_disable() and irq_enable()
Testing some kernel context routines
Testing k_current_get() from an ISR and task
Testing k_is_in_isr() from an ISR
Testing k_is_in_isr() from a preemtible thread
Spawning a thread from a task
Thread to test k_current_get() and k_is_in_isr()
Thread to test k_yield()
Testing k_busy_wait()
Thread busy waiting for 20000 usecs
Thread busy waiting completed
Testing k_sleep()
 thread sleeping for 50 milliseconds
 thread back from sleep
Testing k_thread_create() without cancellation
 thread (q order: 2, t/o: 500) is running
 got thread (q order: 2, t/o: 500) as expected
 thread (q order: 3, t/o: 750) is running
 got thread (q order: 3, t/o: 750) as expected
 thread (q order: 0, t/o: 1000) is running
 got thread (q order: 0, t/o: 1000) as expected
 thread (q order: 6, t/o: 1250) is running
 got thread (q order: 6, t/o: 1250) as expected
 thread (q order: 1, t/o: 1500) is running
 got thread (q order: 1, t/o: 1500) as expected
 thread (q order: 4, t/o: 1750) is running
 got thread (q order: 4, t/o: 1750) as expected
 thread (q order: 5, t/o: 2000) is running
 got thread (q order: 5, t/o: 2000) as expected
Testing k_thread_create() with cancellations
 cancelling [q order: 0, t/o: 1000, t/o order: 0]
 thread (q order: 3, t/o: 750) is running
 got (q order: 3, t/o: 750, t/o order 1) as expected
 thread (q order: 0, t/o: 1000) is running
 got (q order: 0, t/o: 1000, t/o order 2) as expected
 cancelling [q order: 3, t/o: 750, t/o order: 3]
 cancelling [q order: 4, t/o: 1750, t/o order: 4]
 thread (q order: 4, t/o: 1750) is running
 got (q order: 4, t/o: 1750, t/o order 5) as expected
 cancelling [q order: 6, t/o: 1250, t/o order: 6]
PASS - main.
===================================================================
PROJECT EXECUTION SUCCESSFUL