105 lines
3.3 KiB
ReStructuredText
105 lines
3.3 KiB
ReStructuredText
.. _adxl372:
|
|
|
|
ADXL372: Three Axis High-g I2C/SPI Accelerometer
|
|
################################################
|
|
|
|
Description
|
|
***********
|
|
|
|
This sample application produces slightly different outputs based on the chosen
|
|
driver configuration mode:
|
|
|
|
* In **Measuring Mode with trigger support**,
|
|
the acceleration on all three axis is printed in m/s^2 at the sampling rate (ODR).
|
|
* In **Polled Measuring Mode**, the instantaneous acceleration is polled every 2 seconds.
|
|
* In **Max Peak Detect Mode**, the device returns only the over-threshold
|
|
peak acceleration between two consecutive sample fetches or trigger events.
|
|
(In most high-g applications, a single 3-axis acceleration sample at the peak
|
|
of an impact event contains sufficient information about the event, and the
|
|
full acceleration history is not required.) Instead of printing the acceleration
|
|
on all three axis, the sample application calculates the vector magnitude
|
|
(root sum squared) and displays the result in g's rather than in m/s^2,
|
|
together with an bar graph.
|
|
|
|
|
|
References
|
|
**********
|
|
|
|
- ADXL372: http://www.analog.com/adxl372
|
|
|
|
Wiring
|
|
*******
|
|
|
|
This sample uses the ADXL372 sensor controlled either using the I2C or SPI interface.
|
|
Connect supply **VDD**, **VS** and **GND**. The supply voltage can be in
|
|
the 1.6V to 3.5V range.
|
|
|
|
I2C mode
|
|
========
|
|
|
|
Connect Interface: **SDA**, **SCL** and optionally connect the **INT1** to a
|
|
interrupt capable GPIO. It is a requirement that **SCLK** must be connected to
|
|
**GND** in I2C mode. Depending on the baseboard used, the **SDA** and **SCL**
|
|
lines require Pull-Up resistors. With the **MISO** pin low, the I2C address for
|
|
the device is 0x1D, and an alternate I2C address of 0x53 can be chosen by
|
|
pulling the **MISO** pin high.
|
|
|
|
I2C Address:
|
|
|
|
* **0x1D**: if MISO is pulled low
|
|
* **0x53**: if MISO is pulled high
|
|
|
|
.. Note::
|
|
When sharing an SDA bus, the ADXL372 Silicon Revision < 3 may prevent
|
|
communication with other devices on that bus.
|
|
|
|
SPI mode
|
|
========
|
|
|
|
Connect Interface: **SCLK**, **MISO**, **MOSI** and **/CS** and optionally
|
|
connect the **INT1** to a interrupt capable GPIO.
|
|
|
|
|
|
Building and Running
|
|
********************
|
|
|
|
This project outputs sensor data to the console. It requires an ADXL372
|
|
sensor. It should work with any platform featuring a I2C/SPI peripheral interface.
|
|
It does not work on QEMU.
|
|
In this example below the :ref:`nrf52dk_nrf52832` board is used.
|
|
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/sensor/adxl372
|
|
:board: nrf52dk_nrf52832
|
|
:goals: build flash
|
|
|
|
|
|
Sample Output: Max Peak Detect Mode
|
|
===================================
|
|
|
|
.. code-block:: console
|
|
|
|
Waiting for a threshold event
|
|
23.94 g: ########################
|
|
Waiting for a threshold event
|
|
38.01 g: #######################################
|
|
Waiting for a threshold event
|
|
51.40 g: ####################################################
|
|
Waiting for a threshold event
|
|
63.63 g: ################################################################
|
|
|
|
Sample Output: Measurement Mode
|
|
===============================
|
|
|
|
.. code-block:: console
|
|
|
|
AX= 2.94 AY= -5.88 AZ= 0.98 (m/s^2)
|
|
AX= -4.90 AY= 6.86 AZ= -1.96 (m/s^2)
|
|
AX= 2.94 AY= -2.94 AZ= 8.83 (m/s^2)
|
|
AX= -0.98 AY= -6.86 AZ= -0.98 (m/s^2)
|
|
AX= 6.86 AY= 2.94 AZ= 3.92 (m/s^2)
|
|
AX= -0.98 AY= 4.90 AZ= -3.92 (m/s^2)
|
|
|
|
<repeats endlessly>
|