192 lines
6.5 KiB
ReStructuredText
192 lines
6.5 KiB
ReStructuredText
.. _cc1352r1_launchxl:
|
|
|
|
CC1352R1 LaunchXL
|
|
#################
|
|
|
|
Overview
|
|
********
|
|
|
|
The Texas Instruments CC1352R LaunchPad |trade| (LAUNCHXL-CC1352R1) is a
|
|
development kit for the SimpleLink |trade| multi-Standard CC1352R wireless MCU.
|
|
|
|
See the `TI CC1352R LaunchPad Product Page`_ for details.
|
|
|
|
.. figure:: img/cc1352r1_launchxl.png
|
|
:width: 400px
|
|
:align: center
|
|
:alt: TI CC1352R LaunchPad
|
|
|
|
Texas Instruments CC1352R LaunchPad |trade|
|
|
|
|
Hardware
|
|
********
|
|
|
|
The CC1352R LaunchPad |trade| development kit features the CC1352R wireless MCU.
|
|
The board is equipped with two LEDs, two push buttons and BoosterPack connectors
|
|
for expansion. It also includes an integrated (XDS110) debugger.
|
|
|
|
The CC13522 wireless MCU has a 48 MHz Arm |reg| Cortex |reg|-M4F SoC and an
|
|
integrated Sub-1 and 2.4 GHz transceiver supporting multiple protocols including
|
|
Bluetooth |reg| Low Energy and IEEE |reg| 802.15.4.
|
|
|
|
See the `TI CC1352R Product Page`_ for additional details.
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The CC1352R LaunchPad board configuration supports the following hardware
|
|
features:
|
|
|
|
+-----------+------------+----------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+======================+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+----------------------+
|
|
| NVIC | on-chip | arch/arm |
|
|
+-----------+------------+----------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+----------------------+
|
|
| UART | on-chip | serial |
|
|
+-----------+------------+----------------------+
|
|
| I2C | on-chip | i2c |
|
|
+-----------+------------+----------------------+
|
|
| SPI | on-chip | spi |
|
|
+-----------+------------+----------------------+
|
|
|
|
Other hardware features are not supported by the Zephyr kernel.
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
All I/O signals are accessible from the BoosterPack connectors. Pin function
|
|
aligns with the LaunchPad standard.
|
|
|
|
+-------+-----------+---------------------+
|
|
| Pin | Function | Usage |
|
|
+=======+===========+=====================+
|
|
| DIO3 | GPIO | |
|
|
+-------+-----------+---------------------+
|
|
| DIO4 | I2C_MSSCL | I2C SCL |
|
|
+-------+-----------+---------------------+
|
|
| DIO5 | I2C_MSSDA | I2C SDA |
|
|
+-------+-----------+---------------------+
|
|
| DIO6 | GPIO | Red LED |
|
|
+-------+-----------+---------------------+
|
|
| DIO7 | GPIO | Green LED |
|
|
+-------+-----------+---------------------+
|
|
| DIO8 | SSI0_RX | SPI MISO |
|
|
+-------+-----------+---------------------+
|
|
| DIO9 | SSI0_TX | SPI MOSI |
|
|
+-------+-----------+---------------------+
|
|
| DIO10 | SSI0_CLK | SPI CLK |
|
|
+-------+-----------+---------------------+
|
|
| DIO11 | SSIO_CS | SPI CS |
|
|
+-------+-----------+---------------------+
|
|
| DIO12 | UART0_RX | UART RXD |
|
|
+-------+-----------+---------------------+
|
|
| DIO13 | UART0_TX | UART TXD |
|
|
+-------+-----------+---------------------+
|
|
| DIO14 | GPIO | Button 2 |
|
|
+-------+-----------+---------------------+
|
|
| DIO15 | GPIO | Button 1 |
|
|
+-------+-----------+---------------------+
|
|
| DIO16 | | JTAG TDO |
|
|
+-------+-----------+---------------------+
|
|
| DIO17 | | JTAG TDI |
|
|
+-------+-----------+---------------------+
|
|
| DIO18 | UART0_RTS | UART RTS / JTAG SWO |
|
|
+-------+-----------+---------------------+
|
|
| DIO19 | UART0_CTS | UART CTS |
|
|
+-------+-----------+---------------------+
|
|
| DIO20 | GPIO | Flash CS |
|
|
+-------+-----------+---------------------+
|
|
| DIO21 | GPIO | |
|
|
+-------+-----------+---------------------+
|
|
| DIO22 | GPIO | |
|
|
+-------+-----------+---------------------+
|
|
| DIO23 | AUX_IO | A0 |
|
|
+-------+-----------+---------------------+
|
|
| DIO24 | AUX_IO | A1 |
|
|
+-------+-----------+---------------------+
|
|
| DIO25 | AUX_IO | A2 |
|
|
+-------+-----------+---------------------+
|
|
| DIO26 | AUX_IO | A3 |
|
|
+-------+-----------+---------------------+
|
|
| DIO27 | AUX_IO | A4 |
|
|
+-------+-----------+---------------------+
|
|
| DIO28 | AUX_IO | A5 |
|
|
+-------+-----------+---------------------+
|
|
| DIO29 | AUX_IO | A6 |
|
|
+-------+-----------+---------------------+
|
|
| DIO30 | AUX_IO | A7 |
|
|
+-------+-----------+---------------------+
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Before flashing or debugging ensure the RESET, TMS, TCK, TDO, and TDI jumpers
|
|
are in place. Also place jumpers on the the TXD and RXD signals for a serial
|
|
console using the XDS110 application serial port.
|
|
|
|
Flashing
|
|
========
|
|
|
|
Applications for the ``CC1352R LaunchPad`` board configuration can be built and
|
|
flashed in the usual way (see :ref:`build_an_application` and
|
|
:ref:`application_run` for more details).
|
|
|
|
Here is an example for the :ref:`hello_world` application.
|
|
|
|
First, run your favorite terminal program to listen for output.
|
|
|
|
.. code-block:: console
|
|
|
|
$ screen <tty_device> 115200
|
|
|
|
Replace :code:`<tty_device>` with the port where the XDS110 application
|
|
serial device can be found. For example, :code:`/dev/ttyACM0`.
|
|
|
|
Then build and flash the application in the usual way.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: cc1352r1_launchxl
|
|
:goals: build flash
|
|
|
|
Debugging
|
|
=========
|
|
|
|
You can debug an application in the usual way. Here is an example for the
|
|
:ref:`hello_world` application.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: cc1352r1_launchxl
|
|
:maybe-skip-config:
|
|
:goals: debug
|
|
|
|
Bootloader
|
|
==========
|
|
|
|
The ROM bootloader on CC13x2 and CC26x2 devices is enabled by default. The
|
|
bootloader will start if there is no valid application image in flash or the
|
|
so-called backdoor is enabled (via option
|
|
:option:`CONFIG_CC13X2_CC26X2_BOOTLOADER_BACKDOOR_ENABLE`) and BTN-1 is held
|
|
down during reset. See the bootloader documentation in chapter 10 of the `TI
|
|
CC13x2 / CC26x2 Technical Reference Manual`_ for additional information.
|
|
|
|
References
|
|
**********
|
|
|
|
CC1352R1 LaunchPad Quick Start Guide:
|
|
http://www.ti.com/lit/pdf/swru525
|
|
|
|
.. _TI CC1352R LaunchPad Product Page:
|
|
http://www.ti.com/tool/launchxl-cc1352r1
|
|
|
|
.. _TI CC1352R Product Page:
|
|
http://www.ti.com/product/cc1352r
|
|
|
|
.. _TI CC13x2 / CC26x2 Technical Reference Manual:
|
|
http://www.ti.com/lit/pdf/swcu185
|