81 lines
2.7 KiB
ReStructuredText
81 lines
2.7 KiB
ReStructuredText
.. _ds18b20_sample:
|
|
|
|
DS18B20 1-Wire Temperature Sensor
|
|
#################################
|
|
|
|
Overview
|
|
********
|
|
|
|
This sample shows how to use the Zephyr :ref:`sensor_api` API driver for the
|
|
`Maxim DS18B20`_ temperature sensor.
|
|
|
|
.. _Maxim DS18B20:
|
|
https://www.maximintegrated.com/en/products/sensors/DS18B20.html
|
|
|
|
The sample periodically reads temperature data from the
|
|
first available DS18B20 device discovered in the system. The sample checks the
|
|
sensor in polling mode (without interrupt trigger).
|
|
|
|
Building and Running
|
|
********************
|
|
|
|
The devicetree must have an enabled node with ``compatible = "maxim,ds18b20";``.
|
|
See below for examples and common configurations.
|
|
|
|
If the sensor is not built into your board, start by wiring the sensor pins
|
|
as shown in the Figure Hardware Configuration of the `DS18B20 datasheet`_ at
|
|
page 10.
|
|
|
|
.. _DS18B20 datasheet:
|
|
https://datasheets.maximintegrated.com/en/ds/DS18B20.pdf
|
|
|
|
Boards with a built-in DS18B20 or a board-specific overlay
|
|
==========================================================
|
|
|
|
Your board may have a DS18B20 node configured in its devicetree by default,
|
|
or a board specific overlay file with an DS18B20 node is available.
|
|
Make sure this node has ``status = "okay";``, then build and run with:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/sensor/ds18b20
|
|
:goals: build flash
|
|
:board: nucleo_g0b1re
|
|
|
|
DS18B20 via Arduino Serial pins
|
|
===============================
|
|
|
|
Make sure that you have an external circuit to provide an open-drain interface
|
|
for the 1-Wire bus.
|
|
Once you have wired the sensor and the serial peripheral on the Arduino header
|
|
to the 1-Wire bus, build and flash with:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/sensor/ds18b20
|
|
:goals: build flash
|
|
:gen-args: -DDTC_OVERLAY_FILE=arduino_serial.overlay
|
|
|
|
The devicetree overlay :zephyr_file:`samples/sensor/ds18b20/arduino_serial.overlay`
|
|
should work on any board with a properly configured Arduino pin-compatible Serial
|
|
peripheral.
|
|
|
|
Sample Output
|
|
=============
|
|
|
|
The sample prints output to the serial console. DS18B20 device driver messages
|
|
are also logged. Refer to your board's documentation for information on
|
|
connecting to its serial console.
|
|
|
|
Here is example output for the default application settings, assuming that only
|
|
one DS18B20 sensor is connected to the standard Arduino Serial pins:
|
|
|
|
.. code-block:: none
|
|
|
|
*** Booting Zephyr OS build zephyr-v2.6.0-1929-gf7abe4a6689e ***
|
|
Found device "DS18B20", getting sensor data
|
|
[00:00:00.000,039] <dbg> w1_serial: w1_serial_init: w1-serial initialized, with 1 devices
|
|
[00:00:00.015,140] <dbg> DS18B20: ds18b20_init: Using external power supply: 1
|
|
[00:00:00.021,213] <dbg> DS18B20: ds18b20_init: Init DS18B20: ROM=28b1bb3f070000b9
|
|
|
|
Temp: 25.040000
|
|
Temp: 25.030000
|