189 lines
6.3 KiB
ReStructuredText
189 lines
6.3 KiB
ReStructuredText
.. _mps2_an385_board:
|
|
|
|
ARM V2M MPS2
|
|
############
|
|
|
|
Overview
|
|
********
|
|
|
|
The mps2_an385 board configuration is used by Zephyr applications that run on
|
|
the V2M MPS2 board. It provides support for the ARM Cortex-M3 (AN385) CPU and
|
|
the following devices:
|
|
|
|
- Nested Vectored Interrupt Controller (NVIC)
|
|
- System Tick System Clock (SYSTICK)
|
|
- Cortex-M System Design Kit UART
|
|
|
|
.. image:: img/mps2.png
|
|
:width: 442px
|
|
:align: center
|
|
:height: 335px
|
|
:alt: ARM V2M MPS2
|
|
|
|
More information about the board can be found at the `V2M MPS2 Website`_.
|
|
|
|
The Application Note AN385 can be found at `Application Note AN385`_.
|
|
|
|
Hardware
|
|
********
|
|
|
|
ARM V2M MPS2 provides the following hardware components:
|
|
|
|
- ARM Cortex-M3 (AN385)
|
|
- ARM IoT Subsystem for Cortex-M
|
|
- Form factor: 140x120cm
|
|
- SRAM: 8MB single cycle SRAM, 16MB PSRAM
|
|
- Video: QSVGA touch screen panel, 4bit RGB VGA connector
|
|
- Audio: Audio Codec
|
|
- Debug:
|
|
|
|
- ARM JTAG20 connector
|
|
- ARM parallel trace connector (MICTOR38)
|
|
- 20 pin Cortex debug connector
|
|
- 10 pin Cortex debug connector
|
|
- ILA connector for FPGA debug
|
|
|
|
- Expansion
|
|
|
|
- GPIO
|
|
- SPI
|
|
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The mps2_an385 board configuration supports the following hardware features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| SYSTICK | on-chip | systick |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
Other hardware features are not currently supported by the port.
|
|
See the `V2M MPS2 Website`_ for a complete list of V2M MPS2 board hardware
|
|
features.
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
|
|
.. code-block:: console
|
|
|
|
boards/arm/mps2_an385/mps2_an385_defconfig
|
|
|
|
Interrupt Controller
|
|
====================
|
|
|
|
MPS2 is a Cortex-M3 based SoC and has 15 fixed exceptions and 45 IRQs.
|
|
|
|
A Cortex-M3/4-based board uses vectored exceptions. This means each exception
|
|
calls a handler directly from the vector table.
|
|
|
|
Handlers are provided for exceptions 1-6, 11-12, and 14-15. The table here
|
|
identifies the handlers used for each exception.
|
|
|
|
+------+------------+----------------+--------------------------+
|
|
| Exc# | Name | Remarks | Used by Zephyr Kernel |
|
|
+======+============+================+==========================+
|
|
| 1 | Reset | | system initialization |
|
|
+------+------------+----------------+--------------------------+
|
|
| 2 | NMI | | system fatal error |
|
|
+------+------------+----------------+--------------------------+
|
|
| 3 | Hard fault | | system fatal error |
|
|
+------+------------+----------------+--------------------------+
|
|
| 4 | MemManage | MPU fault | system fatal error |
|
|
+------+------------+----------------+--------------------------+
|
|
| 5 | Bus | | system fatal error |
|
|
+------+------------+----------------+--------------------------+
|
|
| 6 | Usage | undefined | system fatal error |
|
|
| | fault | instruction, | |
|
|
| | | or switch | |
|
|
| | | attempt to ARM | |
|
|
| | | mode | |
|
|
+------+------------+----------------+--------------------------+
|
|
| 11 | SVC | | context switch and |
|
|
| | | | software interrupts |
|
|
+------+------------+----------------+--------------------------+
|
|
| 12 | Debug | | system fatal error |
|
|
| | monitor | | |
|
|
+------+------------+----------------+--------------------------+
|
|
| 14 | PendSV | | context switch |
|
|
+------+------------+----------------+--------------------------+
|
|
| 15 | SYSTICK | | system clock |
|
|
+------+------------+----------------+--------------------------+
|
|
|
|
Pin Mapping
|
|
===========
|
|
|
|
The ARM V2M MPS2 Board has 4 GPIO controllers. These controllers are responsible
|
|
for pin muxing, input/output, pull-up, etc.
|
|
|
|
For mode details please refer to `MPS2 Technical Reference Manual (TRM)`_.
|
|
|
|
System Clock
|
|
============
|
|
|
|
The V2M MPS2 main clock is 24 MHz.
|
|
|
|
Serial Port
|
|
===========
|
|
|
|
The V2M MPS2 processor has five UARTs. Both the UARTs have only two wires for
|
|
RX/TX and no flow control (CTS/RTS) or FIFO. The Zephyr console output, by
|
|
default, is utilizing UART0.
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Flashing
|
|
========
|
|
|
|
V2M MPS2 provides:
|
|
|
|
- A USB connection to the host computer, which exposes a Mass Storage and an
|
|
USB Serial Port.
|
|
- A Serial Flash device, which implements the USB flash disk file storage.
|
|
- A physical UART connection which is relayed over interface USB Serial port.
|
|
|
|
Flashing an application to V2M MPS2
|
|
-----------------------------------
|
|
|
|
The sample application hello_world is being used in this tutorial:
|
|
|
|
.. code-block:: console
|
|
|
|
$ZEPHYR_BASE/samples/hello_world
|
|
|
|
To build the Zephyr kernel and application, enter:
|
|
|
|
.. code-block:: console
|
|
|
|
$ cd $ZEPHYR_BASE
|
|
$ . zephyr-env.sh
|
|
$ cd $ZEPHYR_BASE/samples/hello_world/
|
|
$ make BOARD=mps2_an385
|
|
|
|
Connect the V2M MPS2 to your host computer using the USB port and you should
|
|
see a USB connection which exposes a Mass Storage and a USB Serial Port.
|
|
Copy the generated zephyr.bin in the exposed drive.
|
|
Reset the board and you should be able to see on the corresponding Serial Port
|
|
the following message:
|
|
|
|
.. code-block:: console
|
|
|
|
Hello World! arm
|
|
|
|
|
|
.. _V2M MPS2 Website:
|
|
https://developer.mbed.org/platforms/ARM-MPS2/
|
|
|
|
.. _MPS2 Technical Reference Manual (TRM):
|
|
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0200_05_en/versatile_express_cortex_m_prototyping_systems_v2m_mps2_and_v2m_mps2plus_technical_reference_100112_0200_05_en.pdf
|
|
|
|
.. _Application Note AN385:
|
|
http://infocenter.arm.com/help/topic/com.arm.doc.dai0385c/DAI0385C_cortex_m3_on_v2m_mps2.pdf
|