117 lines
4.0 KiB
YAML
117 lines
4.0 KiB
YAML
# Copyright (c) 2021 Nordic Semiconductor ASA
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
description: |
|
|
The nRF pin controller is a singleton node responsible for controlling
|
|
pin function selection and pin properties. For example, you can use this
|
|
node to route UART0 RX to pin P0.1 and enable the pull-up resistor on the
|
|
pin.
|
|
|
|
The node has the 'pinctrl' node label set in your SoC's devicetree,
|
|
so you can modify it like this:
|
|
|
|
&pinctrl {
|
|
/* your modifications go here */
|
|
};
|
|
|
|
All device pin configurations should be placed in child nodes of the
|
|
'pinctrl' node, as shown in this example:
|
|
|
|
/* You can put this in places like a board-pinctrl.dtsi file in
|
|
* your board directory, or a devicetree overlay in your application.
|
|
*/
|
|
&pinctrl {
|
|
/* configuration for uart0 device, default state */
|
|
uart0_default: uart0_default {
|
|
/* group 1 ('group1' name is arbitrary) */
|
|
group1 {
|
|
/* configure P0.1 as UART_TX and P0.2 as UART_RTS */
|
|
psels = <NRF_PSEL(UART_TX, 0, 1)>, <NRF_PSEL(UART_RTS, 0, 2)>;
|
|
};
|
|
/* group 2 */
|
|
group2 {
|
|
/* configure P0.3 as UART_RX and P0.4 as UART_CTS */
|
|
psels = <NRF_PSEL(UART_RX, 0, 3)>, <NRF_PSEL(UART_CTS, 0, 4)>;
|
|
/* both P0.3 and P0.4 are configured with pull-up */
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
};
|
|
|
|
The 'uart0_default' child node encodes the pin configurations for a
|
|
particular state of a device; in this case, the default (that is, active)
|
|
state. You would specify the low-power configuration for the same device
|
|
in a separate child node.
|
|
|
|
As shown, pin configurations are organized in groups within each child node.
|
|
Each group can specify a list of pin function selections in the 'psels'
|
|
property. The NRF_PSEL macro is used to specify a pin function selection.
|
|
Available pin functions can be found in the
|
|
include/dt-bindings/pinctrl/nrf-pinctrl.h header file.
|
|
|
|
A group can also specify shared pin properties common to all the specified
|
|
pins, such as the 'bias-pull-up' property in group 2. Here is a list of
|
|
supported standard pin properties:
|
|
|
|
- bias-disable: Disable pull-up/down (default behavior, not required).
|
|
- bias-pull-up: Enable pull-up resistor.
|
|
- bias-pull-down: Enable pull-down resistor.
|
|
- low-power-enable: Configure pin as an input with input buffer
|
|
disconnected.
|
|
|
|
Note that bias options are mutually exclusive.
|
|
|
|
To link this pin configuration with a device, use a pinctrl-N property
|
|
for some number N, like this example you could place in your board's DTS
|
|
file:
|
|
|
|
#include "board-pinctrl.dtsi"
|
|
|
|
&uart0 {
|
|
pinctrl-0 = <&uart0_default>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
compatible: "nordic,nrf-pinctrl"
|
|
|
|
include:
|
|
- name: base.yaml
|
|
- name: pincfg-node-group.yaml
|
|
child-binding:
|
|
child-binding:
|
|
property-allowlist:
|
|
- bias-disable
|
|
- bias-pull-down
|
|
- bias-pull-up
|
|
- low-power-enable
|
|
|
|
child-binding:
|
|
description: |
|
|
nRF pin controller pin configuration state nodes.
|
|
child-binding:
|
|
description: |
|
|
nRF pin controller pin configuration group.
|
|
properties:
|
|
psels:
|
|
required: true
|
|
type: array
|
|
description: |
|
|
An array of pins sharing the same group properties. The pins should
|
|
be defined using the NRF_PSEL utility macro that encodes the port,
|
|
pin and function.
|
|
|
|
drive-mode:
|
|
type: int
|
|
default: 0
|
|
description: |
|
|
Pin output drive mode. Available drive modes are pre-defined in
|
|
nrf-pinctrl.h. Note that extra modes may not be available on certain
|
|
devices. Defaults to standard mode for 0 and 1 (NRF_DRIVE_S0S1), the
|
|
SoC default.
|
|
|
|
nordic,invert:
|
|
type: boolean
|
|
description: |
|
|
Invert pin polarity (set the active state to low).
|
|
Only valid for PWM channel output pins.
|