157 lines
2.8 KiB
Plaintext
157 lines
2.8 KiB
Plaintext
/*
|
|
* Copyright (c) 2020 Hans Unzner
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/f4/stm32f410Xb.dtsi>
|
|
#include <st/f4/stm32f410r(8-b)tx-pinctrl.dtsi>
|
|
#include "arduino_r3_connector.dtsi"
|
|
#include "st_morpho_connector.dtsi"
|
|
#include <zephyr/dt-bindings/input/input-event-codes.h>
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32F410RB-NUCLEO board";
|
|
compatible = "st,stm32f410rb-nucleo";
|
|
|
|
chosen {
|
|
zephyr,console = &usart2;
|
|
zephyr,shell-uart = &usart2;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
};
|
|
|
|
leds: leds {
|
|
compatible = "gpio-leds";
|
|
green_led_2: led_2 {
|
|
gpios = <&gpioa 5 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD2";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button {
|
|
label = "User";
|
|
gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
|
|
zephyr,code = <INPUT_KEY_0>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &green_led_2;
|
|
sw0 = &user_button;
|
|
};
|
|
};
|
|
|
|
&clk_lsi {
|
|
status = "okay";
|
|
};
|
|
|
|
&clk_hse {
|
|
hse-bypass;
|
|
clock-frequency = <DT_FREQ_M(8)>; /* STLink 8MHz clock */
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
div-m = <8>;
|
|
mul-n = <384>;
|
|
div-p = <4>;
|
|
div-q = <8>;
|
|
clocks = <&clk_hse>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rcc {
|
|
clocks = <&pll>;
|
|
clock-frequency = <DT_FREQ_M(96)>;
|
|
ahb-prescaler = <1>;
|
|
apb1-prescaler = <2>;
|
|
apb2-prescaler = <1>;
|
|
};
|
|
|
|
&usart1 {
|
|
pinctrl-0 = <&usart1_tx_pb6 &usart1_rx_pb7>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart2 {
|
|
pinctrl-0 = <&usart2_tx_pa2 &usart2_rx_pa3>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb9>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&i2c2 {
|
|
pinctrl-0 = <&i2c2_scl_pb10 &i2c2_sda_pb3>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&spi1 {
|
|
pinctrl-0 = <&spi1_nss_pa4 &spi1_sck_pa5
|
|
&spi1_miso_pa6 &spi1_mosi_pa7>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>,
|
|
<&rcc STM32_SRC_LSI RTC_SEL(2)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&dac1 {
|
|
status = "okay";
|
|
pinctrl-0 = <&dac_out1_pa5>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&flash0 {
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
boot_partition: partition@0 {
|
|
label = "mcuboot";
|
|
reg = <0x00000000 DT_SIZE_K(32)>;
|
|
read-only;
|
|
};
|
|
|
|
/*
|
|
* The flash sectors 2&3 at 0x00008000 and ending at
|
|
* 0x0000ffff
|
|
*/
|
|
slot0_partition: partition@8000 {
|
|
label = "image-0";
|
|
reg = <0x00008000 DT_SIZE_K(32)>;
|
|
};
|
|
/*
|
|
* The flash sectors 4 at 0x00010000 and ending at
|
|
* 0x001ffff
|
|
*/
|
|
slot1_partition: partition@10000 {
|
|
label = "image-1";
|
|
reg = <0x00010000 DT_SIZE_K(32)>;
|
|
};
|
|
scratch_partition: partition@18000 {
|
|
label = "image-scratch";
|
|
reg = <0x00018000 DT_SIZE_K(32)>;
|
|
};
|
|
};
|
|
};
|