82 lines
2.7 KiB
YAML
82 lines
2.7 KiB
YAML
# Copyright (c) 2018 Peter Bigot Consulting, LLC
|
|
# Copyright (c) 2019-2020 Nordic Semiconductor ASA
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
# Common properties used by nodes describing serial flash devices that
|
|
# are compatible with the JESD216 Serial Flash Discoverable Parameters
|
|
# specification.
|
|
#
|
|
# This allows encoding the entire BFP block in devicetree to avoid
|
|
# reading at runtime, while still allowing the driver to pull out extra
|
|
# data of interest, such as erase sizes.
|
|
#
|
|
# Alternatively the BFP block can be absent, but critical fields like
|
|
# size can be provided directly along with the JEDEC ID of the expected
|
|
# device to verify its presence at runtime.
|
|
#
|
|
# Only properties supported by parameter tables documented in the
|
|
# JESD216 standards should be listed in this binding include file.
|
|
|
|
properties:
|
|
jedec-id:
|
|
type: uint8-array
|
|
required: false
|
|
description: JEDEC ID as manufacturer ID, memory type, memory density
|
|
|
|
size:
|
|
type: int
|
|
required: false
|
|
description: flash capacity in bits
|
|
|
|
sfdp-bfp:
|
|
type: uint8-array
|
|
required: false
|
|
description: |
|
|
Contains the 32-bit words in little-endian byte order from the
|
|
JESD216 Serial Flash Discoverable Parameters Basic Flash
|
|
Parameters table. This provides flash-specific configuration
|
|
information in cases were runtime retrieval of SFDP data
|
|
is not desired.
|
|
|
|
has-be32k:
|
|
type: boolean
|
|
required: false
|
|
deprecated: true
|
|
description: Not used after Zephyr 2.3.0
|
|
|
|
quad-enable-requirements:
|
|
type: string
|
|
enum:
|
|
- "NONE"
|
|
- "S2B1v1"
|
|
- "S1B6"
|
|
- "S2B7"
|
|
- "S2B1v4"
|
|
- "S2B1v5"
|
|
- "S2B1v6"
|
|
required: false
|
|
description: |
|
|
Quad Enable Requirements value from JESD216 BFP DW15.
|
|
|
|
Use NONE if the device detects 1-1-4 and 1-4-4 modes by the
|
|
instruction. Use S1B6 if QE is bit 6 of the first status register
|
|
byte, and can be configured by reading then writing one byte with
|
|
RDSR and WRSR. For other fields see the specification.
|
|
|
|
enter-4byte-addr:
|
|
type: int
|
|
required: false
|
|
description: |
|
|
Enter 4-Byte Addressing value from JESD216 BFP DW16
|
|
|
|
This property is ignored if the device is configured to use SFDP data
|
|
from the sfdp-bfp property (CONFIG_SPI_NOR_SFDP_DEVICETREE) or to read
|
|
SFDP properties at runtime (CONFIG_SPI_NOR_SFDP_RUNTIME).
|
|
|
|
For CONFIG_SPI_NOR_SFDP_MINIMAL this is the 8-bit value from bits 31:24
|
|
of DW16 identifying ways a device can be placed into 4-byte addressing
|
|
mode. If provided as a non-zero value the driver assumes that 4-byte
|
|
addressing is require to access the full address range, and
|
|
automatically puts the device into 4-byte address mode when the device
|
|
is initialized.
|