102 lines
2.6 KiB
Plaintext
102 lines
2.6 KiB
Plaintext
# Microchip MEC1501 MCU core series
|
|
|
|
# Copyright (c) 2018 Intel Corporation
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
config SOC_SERIES_MEC15XX
|
|
select ARM
|
|
select CPU_CORTEX_M4
|
|
select CPU_CORTEX_M_HAS_DWT
|
|
select CPU_HAS_ARM_MPU
|
|
select HAS_PM
|
|
|
|
config SOC_MEC1501_HSZ
|
|
select HAS_MEC_HAL
|
|
|
|
if SOC_SERIES_MEC15XX
|
|
|
|
config RTOS_TIMER
|
|
bool "MEC1501 RTOS timer"
|
|
|
|
config SOC_MEC1501_PROC_CLK_DIV
|
|
int "PROC_CLK_DIV"
|
|
default 1
|
|
range 1 48
|
|
help
|
|
This divisor defines a ratio between processor clock (HCLK)
|
|
and master clock (MCK):
|
|
HCLK = MCK / PROC_CLK_DIV
|
|
Allowed divider values: 1, 3, 4, 16, and 48.
|
|
|
|
config SOC_MEC1501_VTR3_1_8V
|
|
bool "VTR3 power rail is tied to 1.8V"
|
|
help
|
|
Set this is if VTR3 power sourcejumper in the board is changed.
|
|
|
|
config SOC_MEC1501_VCI_PINS_AS_GPIOS
|
|
bool "Use VCI block pins as GPIOS"
|
|
default y
|
|
help
|
|
By default these pins are not GPIOs, but HW controlled.
|
|
Set this if VCI pin block HW logic is not required in the board
|
|
design.
|
|
|
|
choice
|
|
prompt "MEC1501 debug interface general configuration"
|
|
default SOC_MEC1501_DEBUG_WITHOUT_TRACING
|
|
depends on SOC_SERIES_MEC15XX
|
|
help
|
|
Select Debug SoC interface support for MEC15xx SoC family
|
|
|
|
config SOC_MEC1501_DEBUG_DISABLED
|
|
bool "Disable debug support"
|
|
help
|
|
Debug port is disabled, JTAG/SWD cannot be enabled. JTAG_RST#
|
|
pin is ignored. All other JTAG pins can be used as GPIOs
|
|
or other non-JTAG alternate functions.
|
|
|
|
config SOC_MEC1501_DEBUG_WITHOUT_TRACING
|
|
bool "Debug support via Serial wire debug"
|
|
help
|
|
JTAG port in SWD mode. UART2 and ADC00-03 can be used.
|
|
|
|
config SOC_MEC1501_DEBUG_AND_TRACING
|
|
bool "Debug support via Serial wire debug with tracing enabled"
|
|
help
|
|
JTAG port is enabled in SWD mode. Refer to tracing options
|
|
to see if ADC00-03 can be used or not.
|
|
|
|
endchoice
|
|
|
|
choice
|
|
prompt "MEC1501 debug interface trace configuration"
|
|
default SOC_MEC1501_DEBUG_AND_ETM_TRACING
|
|
depends on SOC_MEC1501_DEBUG_AND_TRACING
|
|
help
|
|
Select tracing mode for debug interface
|
|
|
|
config SOC_MEC1501_DEBUG_AND_ETM_TRACING
|
|
bool "Debug support via Serial wire debug"
|
|
help
|
|
JTAG port in SWD mode and SWV as tracing method.
|
|
UART2 can be used, but ADC00-03 cannot.
|
|
|
|
config SOC_MEC1501_DEBUG_AND_SWV_TRACING
|
|
bool "debug support via Serial Wire Debug and Viewer"
|
|
help
|
|
JTAG port in SWD mode and SWV as tracing method.
|
|
UART2 cannot be used. ADC00-03 can be used.
|
|
endchoice
|
|
|
|
# GPIO initialization depends on SOC initialization, which happen at
|
|
# CONFIG_KERNEL_INIT_PRIORITY_DEFAULT, so GPIO_INIT_PRIORITY needs to be
|
|
# higher than that.
|
|
if GPIO
|
|
|
|
config GPIO_INIT_PRIORITY
|
|
default 41
|
|
|
|
endif # GPIO
|
|
|
|
endif # SOC_SERIES_MEC15XX
|