96 lines
2.7 KiB
YAML
96 lines
2.7 KiB
YAML
# Copyright (c) 2024 STMicroelectronics
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
description: |
|
|
When setting the odr, power-mode, and range properties in a .dts or .dtsi file you may include
|
|
st_lis2dux12.h and use the macros defined there.
|
|
Example:
|
|
#include <zephyr/dt-bindings/sensor/st_lis2dux12.h>
|
|
lis2dux12: lis2dux12@0 {
|
|
...
|
|
power-mode = <LIS2DUX12_OPER_MODE_LOW_POWER>;
|
|
odr = <LIS2DUX12_DT_ODR_12Hz5>;
|
|
range = <LIS2DUX12_DT_FS_16G>;
|
|
};
|
|
|
|
include: sensor-device.yaml
|
|
|
|
properties:
|
|
int1-gpios:
|
|
type: phandle-array
|
|
description: |
|
|
INT1 pin
|
|
|
|
This pin defaults to active high when produced by the sensor.
|
|
The property value should ensure the flags properly describe
|
|
the signal that is presented to the driver.
|
|
int2-gpios:
|
|
type: phandle-array
|
|
description: |
|
|
INT2 pin
|
|
|
|
This pin defaults to active high when produced by the sensor.
|
|
The property value should ensure the flags properly describe
|
|
the signal that is presented to the driver.
|
|
|
|
drdy-pin:
|
|
type: int
|
|
default: 1
|
|
enum:
|
|
- 1 # drdy is generated from INT1
|
|
- 2 # drdy is generated from INT2
|
|
description: |
|
|
Select DRDY pin number (1 or 2).
|
|
This number represents which of the two interrupt pins
|
|
(INT1 or INT2) the drdy line is attached to. This property is not
|
|
mandatory and if not present it defaults to 1 which is the
|
|
configuration at power-up.
|
|
|
|
|
|
range:
|
|
type: int
|
|
default: 0
|
|
description: |
|
|
Range in g. Default is power-up configuration.
|
|
|
|
- 3 # LIS2DUX12_DT_FS_16G
|
|
- 2 # LIS2DUX12_DT_FS_8G
|
|
- 1 # LIS2DUX12_DT_FS_4G
|
|
- 0 # LIS2DUX12_DT_FS_2G
|
|
|
|
enum: [0, 1, 2, 3]
|
|
|
|
power-mode:
|
|
type: int
|
|
default: 0
|
|
description: |
|
|
Specify the sensor power mode. Default is power-down mode
|
|
|
|
- 0 # LIS2DUX12_OPER_MODE_POWER_DOWN
|
|
- 1 # LIS2DUX12_OPER_MODE_LOW_POWER
|
|
- 2 # LIS2DUX12_OPER_MODE_HIGH_RESOLUTION
|
|
- 3 # LIS2DUX12_OPER_MODE_HIGH_FREQUENCY
|
|
|
|
enum: [0, 1, 2, 3]
|
|
|
|
odr:
|
|
type: int
|
|
default: 0
|
|
description: |
|
|
Specify the default output data rate expressed in samples per second (Hz).
|
|
Default is power-down mode
|
|
- 0 # LIS2DUX12_DT_ODR_OFF
|
|
- 1 # LIS2DUX12_DT_ODR_1Hz_ULP
|
|
- 2 # LIS2DUX12_DT_ODR_3Hz_ULP
|
|
- 3 # LIS2DUX12_DT_ODR_25Hz_ULP
|
|
- 4 # LIS2DUX12_DT_ODR_6Hz
|
|
- 5 # LIS2DUX12_DT_ODR_12Hz5
|
|
- 6 # LIS2DUX12_DT_ODR_25Hz
|
|
- 7 # LIS2DUX12_DT_ODR_50Hz
|
|
- 8 # LIS2DUX12_DT_ODR_100Hz
|
|
- 9 # LIS2DUX12_DT_ODR_200Hz
|
|
- 10 # LIS2DUX12_DT_ODR_400Hz
|
|
- 11 # LIS2DUX12_DT_ODR_800Hz
|
|
|
|
enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11]
|