132 lines
3.3 KiB
YAML
132 lines
3.3 KiB
YAML
# Copyright (c) 2020, Linaro Limited
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
description: |
|
|
Generic pin configuration schema
|
|
|
|
Many data items that are represented in a pin configuration node are
|
|
common and generic. Pin control bindings should use the properties
|
|
defined below where they are applicable; not all of these properties are
|
|
relevant or useful for all hardware or binding structures. Each
|
|
individual binding document should state which of these generic
|
|
properties, if any, are used, and the structure of the DT nodes that
|
|
contain these properties.
|
|
|
|
This is based on Linux, documentation:
|
|
https://www.kernel.org/doc/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
|
|
|
|
properties:
|
|
bias-disable:
|
|
type: boolean
|
|
description: disable any pin bias
|
|
|
|
bias-high-impedance:
|
|
type: boolean
|
|
description: high impedance mode ("third-state", "floating")
|
|
|
|
bias-bus-hold:
|
|
type: boolean
|
|
description: latch weakly
|
|
|
|
bias-pull-up:
|
|
type: boolean
|
|
description: enable pull-up resistor
|
|
|
|
bias-pull-down:
|
|
type: boolean
|
|
description: enable pull-down resistor
|
|
|
|
bias-pull-pin-default:
|
|
type: boolean
|
|
description: use pin's default pull state
|
|
|
|
drive-push-pull:
|
|
type: boolean
|
|
description: drive actively high and low
|
|
|
|
drive-open-drain:
|
|
type: boolean
|
|
description: drive with open drain (hardware AND)
|
|
|
|
drive-open-source:
|
|
type: boolean
|
|
description: drive with open source (hardware OR)
|
|
|
|
drive-strength:
|
|
type: int
|
|
description: maximum sink or source current in mA
|
|
|
|
drive-strength-microamp:
|
|
type: int
|
|
description: maximum sink or source current in μA
|
|
|
|
input-enable:
|
|
type: boolean
|
|
description: |
|
|
enable input on pin (e.g. enable an input buffer, no effect on output)
|
|
|
|
input-disable:
|
|
type: boolean
|
|
description: |
|
|
disable input on pin (e.g. disable an input buffer, no effect on output)
|
|
|
|
input-schmitt-enable:
|
|
type: boolean
|
|
description: enable schmitt-trigger mode
|
|
|
|
input-schmitt-disable:
|
|
type: boolean
|
|
description: disable schmitt-trigger mode
|
|
|
|
input-debounce:
|
|
type: int
|
|
description: |
|
|
Takes the debounce time in μsec, as argument or 0 to disable debouncing
|
|
|
|
power-source:
|
|
type: int
|
|
description: select between different power supplies
|
|
|
|
low-power-enable:
|
|
type: boolean
|
|
description: enable low power mode
|
|
|
|
low-power-disable:
|
|
type: boolean
|
|
description: disable low power mode
|
|
|
|
output-disable:
|
|
type: boolean
|
|
description: disable output on a pin (e.g. disable an output buffer)
|
|
|
|
output-enable:
|
|
type: boolean
|
|
description: |
|
|
enable output on a pin without actively driving it (e.g. enable an output
|
|
buffer)
|
|
|
|
output-low:
|
|
type: boolean
|
|
description: set the pin to output mode with low level
|
|
|
|
output-high:
|
|
type: boolean
|
|
description: set the pin to output mode with high level
|
|
|
|
sleep-hardware-state:
|
|
type: boolean
|
|
description: |
|
|
indicate this is sleep related state which will be programmed into
|
|
the registers for the sleep state
|
|
|
|
slew-rate:
|
|
type: int
|
|
description: set the slew rate
|
|
|
|
skew-delay:
|
|
type: int
|
|
description: |
|
|
This affects the expected clock skew on input pins and the delay
|
|
before latching a value to an output pin. Typically indicates how
|
|
many double-inverters are used to delay the signal.
|