156 lines
5.7 KiB
C
156 lines
5.7 KiB
C
/* pinmux_board_quark_se_dev.c - Quark SE Development Board pinmux driver */
|
|
|
|
/*
|
|
* Copyright (c) 2016 Intel Corporation
|
|
*
|
|
* Licensed under the Apache License, Version 2.0 (the "License");
|
|
* you may not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*/
|
|
|
|
#include <nanokernel.h>
|
|
#include <board.h>
|
|
#include <device.h>
|
|
#include <init.h>
|
|
#include <pinmux.h>
|
|
#include <sys_io.h>
|
|
#include "pinmux/pinmux.h"
|
|
|
|
#include "pinmux_quark_mcu.h"
|
|
|
|
/*
|
|
* This is the full pinmap that we have available on the board for configuration
|
|
* including the ball position and the various modes that can be set. In the
|
|
* _pinmux_defaults we do not spend any time setting values that are using mode
|
|
* A as the hardware brings up all devices by default in mode A.
|
|
*/
|
|
|
|
/* pin, ball, mode A, mode B, mode C */
|
|
/* 0 F02, gpio_0, ain_0, spi_s_cs */
|
|
/* 1 G04, gpio_1, ain_1, spi_s_miso */
|
|
/* 2 H05, gpio_2, ain_2, spi_s_sck */
|
|
/* 3 J06, gpio_3, ain_3, spi_s_mosi */
|
|
/* 4 K06, gpio_4, ain_4, NA */ /* 15.4 GPIO */
|
|
/* 5 L06, gpio_5, ain_5, NA */ /* 15.4 GPIO */
|
|
/* 6 H04, gpio_6, ain_6, NA */ /* 15.4 GPIO */
|
|
/* 7 G03, gpio_7, ain_7, NA */
|
|
/* 8 L05, gpio_ss_0, ain_8, uart1_cts */ /* UART debug */
|
|
/* 9 M05, gpio_ss_1, ain_9, uart1_rts */ /* UART debug */
|
|
/* 10 K05, gpio_ss_2, ain_10 */
|
|
/* 11 G01, gpio_ss_3, ain_11 */
|
|
/* 12 J04, gpio_ss_4, ain_12 */
|
|
/* 13 G02, gpio_ss_5, ain_13 */
|
|
/* 14 F01, gpio_ss_6, ain_14 */
|
|
/* 15 J05, gpio_ss_7, ain_15 */
|
|
/* 16 L04, gpio_ss_8, ain_16, uart1_txd */ /* UART debug */
|
|
/* 17 M04, gpio_ss_9, ain_17, uart1_rxd */ /* UART debug */
|
|
/* 18 K04, uart0_rx, ain_18, NA */ /* BT UART */
|
|
/* 19 B02, uart0_tx, gpio_31, NA */ /* BT UART */
|
|
/* 20 C01, i2c0_scl, NA, NA */ /* EEPROM, BT, Light Sensor */
|
|
/* 21 C02, i2c0_sda, NA, NA */ /* EEPROM, BT, Light Sensor */
|
|
/* 22 D01, i2c1_scl, NA, NA */
|
|
/* 23 D02, i2c1_sda, NA, NA */
|
|
/* 24 E01, i2c0_ss_sda, NA, NA */
|
|
/* 25 E02, i2c0_ss_scl, NA, NA */
|
|
/* 26 B03, i2c1_ss_sda, NA, NA */ /* IMU */
|
|
/* 27 A03, i2c1_ss_scl, NA, NA */ /* IMU */
|
|
/* 28 C03, spi0_ss_miso, NA, NA */ /* IMU */
|
|
/* 29 E03, spi0_ss_mosi, NA, NA */ /* IMU */
|
|
/* 30 D03, spi0_ss_sck, NA, NA */ /* IMU */
|
|
/* 31 D04, spi0_ss_cs0, NA, NA */ /* IMU */
|
|
/* 32 C04, spi0_ss_cs1, NA, NA */
|
|
/* 33 B04, spi0_ss_cs2, gpio_29, NA */ /* 15.4 GPIO */
|
|
/* 34 A04, spi0_ss_cs3, gpio_30, NA */
|
|
/* 35 B05, spi1_ss_miso, NA, NA */
|
|
/* 36 C05, spi1_ss_mosi, NA, NA */
|
|
/* 37 D05, spi1_ss_sck, NA, NA */
|
|
/* 38 E05, spi1_ss_cs0, NA, NA */
|
|
/* 39 E04, spi1_ss_cs1, NA, NA */
|
|
/* 40 A06, spi1_ss_cs2, uart0_cts, NA */ /* BT UART */
|
|
/* 41 B06, spi1_ss_cs3, uart0_rts, NA */ /* BT UART */
|
|
/* 42 C06, gpio_8, spi1_m_sck, NA */ /* 15.4 SPI */
|
|
/* 43 D06, gpio_9, spi1_m_miso, NA */ /* 15.4 SPI */
|
|
/* 44 E06, gpio_10, spi1_m_mosi, NA */ /* 15.4 SPI */
|
|
/* 45 D07, gpio_11, spi1_m_cs0, NA */ /* 15.4 SPI GPIO CS */
|
|
/* 46 C07, gpio_12, spi1_m_cs1, NA */
|
|
/* 47 B07, gpio_13, spi1_m_cs2, NA */
|
|
/* 48 A07, gpio_14, spi1_m_cs3, NA */
|
|
/* 49 B08, gpio_15, i2s_rxd, NA */
|
|
/* 50 A08, gpio_16, i2s_rscki, NA */
|
|
/* 51 B09, gpio_17, i2s_rws, NA */
|
|
/* 52 A09, gpio_18, i2s_tsck, NA */
|
|
/* 53 C09, gpio_19, i2s_twsi, NA */
|
|
/* 54 D09, gpio_20, i2s_txd, NA */
|
|
/* 55 D08, gpio_21, spi0_m_sck, NA */ /* SPI Flash */
|
|
/* 56 E07, gpio_22, spi0_m_miso, NA */ /* SPI Flash */
|
|
/* 57 E09, gpio_23, spi0_m_mosi, NA */ /* SPI Flash */
|
|
/* 58 E08, gpio_24, spi0_m_cs0, NA */ /* SPI Flash */
|
|
/* 59 A10, gpio_25, spi0_m_cs1, NA */
|
|
/* 60 B10, gpio_26, spi0_m_cs2, NA */
|
|
/* 61 C10, gpio_27, spi0_m_cs3, NA */
|
|
/* 62 D10, gpio_28, NA, NA */
|
|
/* 63 E10, gpio_ss_10, pwm_0, NA */
|
|
/* 64 D11, gpio_ss_11, pwm_1, NA */
|
|
/* 65 C11, gpio_ss_12, pwm_2, NA */
|
|
/* 66 B11, gpio_ss_13, pwm_3, NA */
|
|
/* 67 D12, gpio_ss_14, clkout_32khz, NA */
|
|
/* 68 C12, gpio_ss_15, clkout_16mhz, NA */
|
|
|
|
/*
|
|
* On the QUARK_SE platform there are a minimum of 69 pins that can be possibly
|
|
* set. This would be a total of 5 registers to store the configuration as per
|
|
* the bit description from above
|
|
*/
|
|
#define PINMUX_MAX_REGISTERS 5
|
|
static void _pinmux_defaults(uint32_t base)
|
|
{
|
|
uint32_t mux_config[PINMUX_MAX_REGISTERS] = { 0, 0, 0, 0, 0};
|
|
int i = 0;
|
|
|
|
PIN_CONFIG(mux_config, 0, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 1, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 2, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 3, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 8, PINMUX_FUNC_C);
|
|
PIN_CONFIG(mux_config, 9, PINMUX_FUNC_C);
|
|
PIN_CONFIG(mux_config, 16, PINMUX_FUNC_C);
|
|
PIN_CONFIG(mux_config, 17, PINMUX_FUNC_C);
|
|
PIN_CONFIG(mux_config, 33, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 40, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 41, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 42, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 43, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 44, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 55, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 56, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 57, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 58, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 63, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 64, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 65, PINMUX_FUNC_B);
|
|
PIN_CONFIG(mux_config, 66, PINMUX_FUNC_B);
|
|
|
|
for (i = 0; i < PINMUX_MAX_REGISTERS; i++) {
|
|
sys_write32(mux_config[i], PINMUX_SELECT_REGISTER(base, i));
|
|
}
|
|
}
|
|
|
|
static int pinmux_initialize(struct device *port)
|
|
{
|
|
ARG_UNUSED(port);
|
|
|
|
_pinmux_defaults(PINMUX_BASE_ADDR);
|
|
|
|
return 0;
|
|
}
|
|
|
|
SYS_INIT(pinmux_initialize, SECONDARY, CONFIG_KERNEL_INIT_PRIORITY_DEFAULT);
|