166 lines
2.8 KiB
Plaintext
166 lines
2.8 KiB
Plaintext
/*
|
|
* Copyright (c) 2017 Shawn Nock <shawn@monadnock.ca>
|
|
* Copyright (c) 2017 Linaro Limited
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <nordic/nrf52832_qfaa.dtsi>
|
|
|
|
/ {
|
|
model = "Nordic PCA10040 Dev Kit";
|
|
compatible = "nordic,pca10040-dk", "nordic,nrf52832-qfaa",
|
|
"nordic,nrf52832";
|
|
|
|
chosen {
|
|
zephyr,console = &uart0;
|
|
zephyr,uart-mcumgr = &uart0;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
led0: led_0 {
|
|
gpios = <&gpio0 17 GPIO_INT_ACTIVE_LOW>;
|
|
label = "Green LED 0";
|
|
};
|
|
led1: led_1 {
|
|
gpios = <&gpio0 18 GPIO_INT_ACTIVE_LOW>;
|
|
label = "Green LED 1";
|
|
};
|
|
led2: led_2 {
|
|
gpios = <&gpio0 19 GPIO_INT_ACTIVE_LOW>;
|
|
label = "Green LED 2";
|
|
};
|
|
led3: led_3 {
|
|
gpios = <&gpio0 20 GPIO_INT_ACTIVE_LOW>;
|
|
label = "Green LED 3";
|
|
};
|
|
};
|
|
|
|
buttons {
|
|
compatible = "gpio-keys";
|
|
button0: button_0 {
|
|
gpios = <&gpio0 13 GPIO_PUD_PULL_UP>;
|
|
label = "Push button switch 0";
|
|
};
|
|
button1: button_1 {
|
|
gpios = <&gpio0 14 GPIO_PUD_PULL_UP>;
|
|
label = "Push button switch 1";
|
|
};
|
|
button2: button_2 {
|
|
gpios = <&gpio0 15 GPIO_PUD_PULL_UP>;
|
|
label = "Push button switch 2";
|
|
};
|
|
button3: button_3 {
|
|
gpios = <&gpio0 16 GPIO_PUD_PULL_UP>;
|
|
label = "Push button switch 3";
|
|
};
|
|
};
|
|
|
|
/* These aliases are provided for compatibility with samples */
|
|
aliases {
|
|
led0 = &led0;
|
|
led1 = &led1;
|
|
led2 = &led2;
|
|
led3 = &led3;
|
|
sw0 = &button0;
|
|
sw1 = &button1;
|
|
sw2 = &button2;
|
|
sw3 = &button3;
|
|
};
|
|
};
|
|
|
|
&adc {
|
|
status ="ok";
|
|
};
|
|
|
|
&gpiote {
|
|
status ="ok";
|
|
};
|
|
|
|
&gpio0 {
|
|
status ="ok";
|
|
};
|
|
|
|
&uart0 {
|
|
status = "ok";
|
|
compatible = "nordic,nrf-uart";
|
|
current-speed = <115200>;
|
|
tx-pin = <6>;
|
|
rx-pin = <8>;
|
|
rts-pin = <5>;
|
|
cts-pin = <7>;
|
|
};
|
|
|
|
&i2c0 {
|
|
status = "ok";
|
|
sda-pin = <26>;
|
|
scl-pin = <27>;
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "ok";
|
|
sda-pin = <30>;
|
|
scl-pin = <31>;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "ok";
|
|
sck-pin = <27>;
|
|
mosi-pin = <26>;
|
|
miso-pin = <25>;
|
|
};
|
|
|
|
&spi1 {
|
|
status = "ok";
|
|
sck-pin = <31>;
|
|
mosi-pin = <30>;
|
|
miso-pin = <29>;
|
|
};
|
|
|
|
&spi2 {
|
|
status = "ok";
|
|
sck-pin = <22>;
|
|
mosi-pin = <23>;
|
|
miso-pin = <24>;
|
|
};
|
|
|
|
&flash0 {
|
|
/*
|
|
* For more information, see:
|
|
* http://docs.zephyrproject.org/latest/devices/dts/flash_partitions.html
|
|
*/
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
boot_partition: partition@0 {
|
|
label = "mcuboot";
|
|
reg = <0x00000000 0xc000>;
|
|
};
|
|
slot0_partition: partition@c000 {
|
|
label = "image-0";
|
|
reg = <0x0000C000 0x32000>;
|
|
};
|
|
slot1_partition: partition@3e000 {
|
|
label = "image-1";
|
|
reg = <0x0003E000 0x32000>;
|
|
};
|
|
scratch_partition: partition@70000 {
|
|
label = "image-scratch";
|
|
reg = <0x00070000 0xa000>;
|
|
};
|
|
|
|
#if defined(CONFIG_FS_FLASH_STORAGE_PARTITION)
|
|
storage_partition: partition@7a000 {
|
|
label = "storage";
|
|
reg = <0x0007a000 0x00006000>;
|
|
};
|
|
#endif
|
|
};
|
|
};
|